From: Markus Mayer <code@mmayer.net>
To: Zhang Rui <rui.zhang@intel.com>,
        Eduardo Valentin <edubezval@gmail.com>,
        Rob Herring <robh+dt@kernel.org>, Mark Rutland <mark.rutland@arm.com>,
        Doug Berger <opendmb@gmail.com>,
        Brian Norris <computersforpeace@gmail.com>,
        Gregory Fong <gregory.0xf0@gmail.com>,
        Florian Fainelli <f.fainelli@gmail.com>,
        =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
Cc: Broadcom Kernel List <bcm-kernel-feedback-list@broadcom.com>,
        Power Management List <linux-pm@vger.kernel.org>,
        Device Tree List <devicetree@vger.kernel.org>,
        ARM Kernel List <linux-arm-kernel@lists.infradead.org>,
        Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
        Markus Mayer <mmayer@broadcom.com>
Subject: [PATCH 2/2] thermal: add brcmstb AVS TMON driver
Date: Mon,  5 Jun 2017 14:09:30 -0700
Message-Id: <20170605210930.65432-3-code@mmayer.net>
In-Reply-To: <20170605210930.65432-1-code@mmayer.net>
References: <20170605210930.65432-1-code@mmayer.net>
Sender: linux-kernel-owner@vger.kernel.org
Content-Length: 12024
Lines: 418

From: Brian Norris <computersforpeace@gmail.com>

The AVS TMON core provides temperature readings, a pair of configurable
high- and low-temperature threshold interrupts, and an emergency
over-temperature chip reset. The driver utilizes the first two to
provide temperature readings and high-temperature notifications to
applications. The over-temperature reset is not exposed to
applications; this reset threshold is critical to the system and should
be set with care within the bootloader.

Applications may choose to utilize the notification mechanism, the
temperature reading mechanism (e.g., through polling), or both.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
---
 drivers/thermal/broadcom/Kconfig           |   7 +
 drivers/thermal/broadcom/Makefile          |   1 +
 drivers/thermal/broadcom/brcmstb_thermal.c | 361 +++++++++++++++++++++++++++++
 3 files changed, 369 insertions(+)
 create mode 100644 drivers/thermal/broadcom/brcmstb_thermal.c

diff --git a/drivers/thermal/broadcom/Kconfig b/drivers/thermal/broadcom/Kconfig
index ab08af4..12e621d 100644
--- a/drivers/thermal/broadcom/Kconfig
+++ b/drivers/thermal/broadcom/Kconfig
@@ -6,6 +6,13 @@ config BCM2835_THERMAL
 	help
 	  Support for thermal sensors on Broadcom bcm2835 SoCs.
 
+config BRCMSTB_THERMAL
+	tristate "Broadcom STB AVS TMON thermal driver"
+	depends on ARCH_BRCMSTB || COMPILE_TEST
+	help
+	  Enable this driver if you have a Broadcom STB SoC and would like
+	  thermal framework support.
+
 config BCM_NS_THERMAL
 	tristate "Northstar thermal driver"
 	depends on ARCH_BCM_IPROC || COMPILE_TEST
diff --git a/drivers/thermal/broadcom/Makefile b/drivers/thermal/broadcom/Makefile
index c6f62e4..fae10ec 100644
--- a/drivers/thermal/broadcom/Makefile
+++ b/drivers/thermal/broadcom/Makefile
@@ -1,2 +1,3 @@
 obj-$(CONFIG_BCM2835_THERMAL)		+= bcm2835_thermal.o
+obj-$(CONFIG_BRCMSTB_THERMAL)		+= brcmstb_thermal.o
 obj-$(CONFIG_BCM_NS_THERMAL)		+= ns-thermal.o
diff --git a/drivers/thermal/broadcom/brcmstb_thermal.c b/drivers/thermal/broadcom/brcmstb_thermal.c
new file mode 100644
index 0000000..027648c
--- /dev/null
+++ b/drivers/thermal/broadcom/brcmstb_thermal.c
@@ -0,0 +1,361 @@
+/*
+ * Broadcom STB AVS TMON thermal sensor driver
+ *
+ * Copyright (c) 2015-2017 Broadcom
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#define DRV_NAME	"brcmstb_thermal"
+
+#define pr_fmt(fmt)	DRV_NAME ": " fmt
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/irqreturn.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/thermal.h>
+
+#define AVS_TMON_STATUS			0x00
+ #define AVS_TMON_STATUS_valid_msk	BIT(11)
+ #define AVS_TMON_STATUS_data_msk	GENMASK(10, 1)
+ #define AVS_TMON_STATUS_data_shift	1
+
+#define AVS_TMON_EN_OVERTEMP_RESET	0x04
+ #define AVS_TMON_EN_OVERTEMP_RESET_msk	BIT(0)
+
+#define AVS_TMON_RESET_THRESH		0x08
+ #define AVS_TMON_RESET_THRESH_msk	GENMASK(10, 1)
+ #define AVS_TMON_RESET_THRESH_shift	1
+
+#define AVS_TMON_INT_IDLE_TIME		0x10
+
+#define AVS_TMON_EN_TEMP_INT_SRCS	0x14
+ #define AVS_TMON_EN_TEMP_INT_SRCS_high	BIT(1)
+ #define AVS_TMON_EN_TEMP_INT_SRCS_low	BIT(0)
+
+#define AVS_TMON_INT_THRESH		0x18
+ #define AVS_TMON_INT_THRESH_high_msk	GENMASK(26, 17)
+ #define AVS_TMON_INT_THRESH_high_shift	17
+ #define AVS_TMON_INT_THRESH_low_msk	GENMASK(10, 1)
+ #define AVS_TMON_INT_THRESH_low_shift	1
+
+#define AVS_TMON_TEMP_INT_CODE		0x1c
+#define AVS_TMON_TP_TEST_ENABLE		0x20
+
+enum avs_tmon_trip_type {
+	TMON_TRIP_TYPE_LOW = 0,
+	TMON_TRIP_TYPE_HIGH,
+	TMON_TRIP_TYPE_RESET,
+	TMON_TRIP_TYPE_MAX,
+};
+
+struct avs_tmon_trip {
+	/* HW bit to enable the trip */
+	u32 enable_offs;
+	u32 enable_mask;
+
+	/* HW field to read the trip temperature */
+	u32 reg_offs;
+	u32 reg_msk;
+	int reg_shift;
+};
+
+static struct avs_tmon_trip avs_tmon_trips[] = {
+	/* Trips when temperature is below threshold */
+	[TMON_TRIP_TYPE_LOW] = {
+		.enable_offs	= AVS_TMON_EN_TEMP_INT_SRCS,
+		.enable_mask	= AVS_TMON_EN_TEMP_INT_SRCS_low,
+		.reg_offs	= AVS_TMON_INT_THRESH,
+		.reg_msk	= AVS_TMON_INT_THRESH_low_msk,
+		.reg_shift	= AVS_TMON_INT_THRESH_low_shift,
+	},
+	/* Trips when temperature is above threshold */
+	[TMON_TRIP_TYPE_HIGH] = {
+		.enable_offs	= AVS_TMON_EN_TEMP_INT_SRCS,
+		.enable_mask	= AVS_TMON_EN_TEMP_INT_SRCS_high,
+		.reg_offs	= AVS_TMON_INT_THRESH,
+		.reg_msk	= AVS_TMON_INT_THRESH_high_msk,
+		.reg_shift	= AVS_TMON_INT_THRESH_high_shift,
+	},
+	/* Automatically resets chip when above threshold */
+	[TMON_TRIP_TYPE_RESET] = {
+		.enable_offs	= AVS_TMON_EN_OVERTEMP_RESET,
+		.enable_mask	= AVS_TMON_EN_OVERTEMP_RESET_msk,
+		.reg_offs	= AVS_TMON_RESET_THRESH,
+		.reg_msk	= AVS_TMON_RESET_THRESH_msk,
+		.reg_shift	= AVS_TMON_RESET_THRESH_shift,
+	},
+};
+
+struct brcmstb_thermal_priv {
+	void __iomem *tmon_base;
+	struct device *dev;
+	struct thermal_zone_device *thermal;
+};
+
+/* Convert a HW code to a temperature reading (millidegree celsius) */
+static inline int avs_tmon_code_to_temp(u32 code)
+{
+	return (410040 - (int)((code & 0x3FF) * 487));
+}
+
+/*
+ * Convert a temperature value (millidegree celsius) to a HW code
+ *
+ * @temp: temperature to convert
+ * @low: if true, round toward the low side
+ */
+static inline u32 avs_tmon_temp_to_code(int temp, bool low)
+{
+	if (temp < -88161)
+		return 0x3FF;	/* Maximum code value */
+
+	if (temp >= 410040)
+		return 0;	/* Minimum code value */
+
+	if (low)
+		return (u32)(DIV_ROUND_UP(410040 - temp, 487));
+	else
+		return (u32)((410040 - temp) / 487);
+}
+
+static int brcmstb_get_temp(void *data, int *temp)
+{
+	struct brcmstb_thermal_priv *priv = data;
+	u32 val;
+	long t;
+
+	val = __raw_readl(priv->tmon_base + AVS_TMON_STATUS);
+
+	if (!(val & AVS_TMON_STATUS_valid_msk)) {
+		dev_err(priv->dev, "reading not valid\n");
+
+		return -EIO;
+	}
+
+	val = (val & AVS_TMON_STATUS_data_msk) >> AVS_TMON_STATUS_data_shift;
+
+	t = avs_tmon_code_to_temp(val);
+	if (t < 0)
+		*temp = 0;
+	else
+		*temp = t;
+
+	return 0;
+}
+
+static void avs_tmon_trip_enable(struct brcmstb_thermal_priv *priv,
+				 enum avs_tmon_trip_type type, int en)
+{
+	struct avs_tmon_trip *trip = &avs_tmon_trips[type];
+	u32 val = __raw_readl(priv->tmon_base + trip->enable_offs);
+
+	pr_debug("%s trip, type %d\n", en ? "enable" : "disable", type);
+
+	if (en)
+		val |= trip->enable_mask;
+	else
+		val &= ~trip->enable_mask;
+
+	__raw_writel(val, priv->tmon_base + trip->enable_offs);
+}
+
+static int avs_tmon_get_trip_temp(struct brcmstb_thermal_priv *priv,
+				  enum avs_tmon_trip_type type)
+{
+	struct avs_tmon_trip *trip = &avs_tmon_trips[type];
+	u32 val = __raw_readl(priv->tmon_base + trip->reg_offs);
+
+	val &= trip->reg_msk;
+	val >>= trip->reg_shift;
+
+	return avs_tmon_code_to_temp(val);
+}
+
+static void avs_tmon_set_trip_temp(struct brcmstb_thermal_priv *priv,
+				   enum avs_tmon_trip_type type,
+				   int temp)
+{
+	struct avs_tmon_trip *trip = &avs_tmon_trips[type];
+	u32 val, orig;
+
+	pr_debug("set temp %d to %d\n", type, temp);
+
+	/* round toward low temp for the low interrupt */
+	val = avs_tmon_temp_to_code(temp, type == TMON_TRIP_TYPE_LOW);
+
+	/* TODO: Check for overflow? */
+	val <<= trip->reg_shift;
+	val &= trip->reg_msk;
+
+	orig = __raw_readl(priv->tmon_base + trip->reg_offs);
+	orig &= ~trip->reg_msk;
+	orig |= val;
+	__raw_writel(orig, priv->tmon_base + trip->reg_offs);
+}
+
+static int avs_tmon_get_intr_temp(struct brcmstb_thermal_priv *priv)
+{
+	u32 val;
+
+	val = __raw_readl(priv->tmon_base + AVS_TMON_TEMP_INT_CODE);
+	return avs_tmon_code_to_temp(val);
+}
+
+static irqreturn_t brcmstb_tmon_irq_thread(int irq, void *data)
+{
+	struct brcmstb_thermal_priv *priv = data;
+	int low, high, intr;
+
+	low = avs_tmon_get_trip_temp(priv, TMON_TRIP_TYPE_LOW);
+	high = avs_tmon_get_trip_temp(priv, TMON_TRIP_TYPE_HIGH);
+	intr = avs_tmon_get_intr_temp(priv);
+
+	dev_dbg(priv->dev, "low/intr/high: %d/%d/%d\n",
+			low, intr, high);
+
+	/* Disable high-temp until next threshold shift */
+	if (intr >= high)
+		avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_HIGH, 0);
+	/* Disable low-temp until next threshold shift */
+	if (intr <= low)
+		avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_LOW, 0);
+
+	/*
+	 * Notify using the interrupt temperature, in case the temperature
+	 * changes before it can next be read out
+	 */
+	thermal_zone_device_update(priv->thermal, intr);
+
+	return IRQ_HANDLED;
+}
+
+static int brcmstb_set_trips(void *data, int low, int high)
+{
+	struct brcmstb_thermal_priv *priv = data;
+
+	pr_debug("set trips %d <--> %d\n", low, high);
+
+	if (low) {
+		if (low > INT_MAX)
+			low = INT_MAX;
+		avs_tmon_set_trip_temp(priv, TMON_TRIP_TYPE_LOW, (int)low);
+		avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_LOW, 1);
+	} else {
+		avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_LOW, 0);
+	}
+
+	if (high < ULONG_MAX) {
+		if (high > INT_MAX)
+			high = INT_MAX;
+		avs_tmon_set_trip_temp(priv, TMON_TRIP_TYPE_HIGH, (int)high);
+		avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_HIGH, 1);
+	} else {
+		avs_tmon_trip_enable(priv, TMON_TRIP_TYPE_HIGH, 0);
+	}
+
+	return 0;
+}
+
+static struct thermal_zone_of_device_ops of_ops = {
+	.get_temp	= brcmstb_get_temp,
+	.set_trips	= brcmstb_set_trips,
+};
+
+static const struct of_device_id brcmstb_thermal_id_table[] = {
+	{ .compatible = "brcm,avs-tmon" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, brcmstb_thermal_id_table);
+
+static int brcmstb_thermal_probe(struct platform_device *pdev)
+{
+	struct thermal_zone_device *thermal;
+	struct brcmstb_thermal_priv *priv;
+	struct resource *res;
+	int irq, ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->tmon_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->tmon_base))
+		return PTR_ERR(priv->tmon_base);
+
+	priv->dev = &pdev->dev;
+	platform_set_drvdata(pdev, priv);
+
+	thermal = thermal_zone_of_sensor_register(&pdev->dev, 0, priv, &of_ops);
+	if (IS_ERR(thermal)) {
+		ret = PTR_ERR(thermal);
+		dev_err(&pdev->dev, "could not register sensor: %d\n", ret);
+		goto err;
+	}
+
+	priv->thermal = thermal;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "could not get IRQ\n");
+		ret = irq;
+		goto err;
+	}
+	ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+					brcmstb_tmon_irq_thread, IRQF_ONESHOT,
+					DRV_NAME, priv);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "could not request IRQ: %d\n", ret);
+		goto err;
+	}
+
+	dev_info(&pdev->dev, "registered AVS TMON of-sensor driver\n");
+
+	return 0;
+
+err:
+	thermal_zone_of_sensor_unregister(&pdev->dev, priv->thermal);
+	return ret;
+}
+
+static int brcmstb_thermal_exit(struct platform_device *pdev)
+{
+	struct brcmstb_thermal_priv *priv = platform_get_drvdata(pdev);
+	struct thermal_zone_device *thermal = priv->thermal;
+
+	if (thermal)
+		thermal_zone_of_sensor_unregister(&pdev->dev, priv->thermal);
+
+	return 0;
+}
+
+static struct platform_driver brcmstb_thermal_driver = {
+	.probe = brcmstb_thermal_probe,
+	.remove = brcmstb_thermal_exit,
+	.driver = {
+		.name = DRV_NAME,
+		.owner = THIS_MODULE,
+		.of_match_table = brcmstb_thermal_id_table,
+	},
+};
+module_platform_driver(brcmstb_thermal_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Brian Norris");
+MODULE_DESCRIPTION("Broadcom STB AVS TMON thermal driver");
-- 
2.7.4