Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1751848AbdFIJPf (ORCPT ); Fri, 9 Jun 2017 05:15:35 -0400 Received: from rtits2.realtek.com ([211.75.126.72]:41069 "EHLO rtits2.realtek.com.tw" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751558AbdFIJMh (ORCPT ); Fri, 9 Jun 2017 05:12:37 -0400 Authenticated-By: X-SpamFilter-By: BOX Solutions SpamTrap 5.59 with qID v599CUa5015365, This message is accepted by code: ctloc85258 From: Hayes Wang To: CC: , , , Hayes Wang Subject: [PATCH net-next 07/11] r8152: move the default coalesce setting for RTL8153 Date: Fri, 9 Jun 2017 17:11:44 +0800 Message-ID: <1394712342-15778-267-Taiwan-albertk@realtek.com> X-Mailer: Microsoft Office Outlook 11 In-Reply-To: <1394712342-15778-260-Taiwan-albertk@realtek.com> References: <1394712342-15778-260-Taiwan-albertk@realtek.com> MIME-Version: 1.0 Content-Type: text/plain X-Originating-IP: [172.21.177.200] Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 1401 Lines: 54 Only RTL8153 could set coalesce, so move the default setting for rtl8152_probe() to r8153_init(). Signed-off-by: Hayes Wang --- drivers/net/usb/r8152.c | 26 +++++++++++++------------- 1 file changed, 13 insertions(+), 13 deletions(-) diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c index 565ac5b..f78111c 100644 --- a/drivers/net/usb/r8152.c +++ b/drivers/net/usb/r8152.c @@ -3579,6 +3579,19 @@ static void r8153_init(struct r8152 *tp) ocp_write_word(tp, MCU_TYPE_USB, USB_USB_CTRL, ocp_data); rtl_tally_reset(tp); + + switch (tp->udev->speed) { + case USB_SPEED_SUPER: + case USB_SPEED_SUPER_PLUS: + tp->coalesce = COALESCE_SUPER; + break; + case USB_SPEED_HIGH: + tp->coalesce = COALESCE_HIGH; + break; + default: + tp->coalesce = COALESCE_SLOW; + break; + } } static int rtl8152_pre_reset(struct usb_interface *intf) @@ -4524,19 +4537,6 @@ static int rtl8152_probe(struct usb_interface *intf, tp->mii.reg_num_mask = 0x1f; tp->mii.phy_id = R8152_PHY_ID; - switch (udev->speed) { - case USB_SPEED_SUPER: - case USB_SPEED_SUPER_PLUS: - tp->coalesce = COALESCE_SUPER; - break; - case USB_SPEED_HIGH: - tp->coalesce = COALESCE_HIGH; - break; - default: - tp->coalesce = COALESCE_SLOW; - break; - } - tp->autoneg = AUTONEG_ENABLE; tp->speed = tp->mii.supports_gmii ? SPEED_1000 : SPEED_100; tp->duplex = DUPLEX_FULL; -- 2.7.4