Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1751840AbdF3J7D (ORCPT ); Fri, 30 Jun 2017 05:59:03 -0400 Received: from mail-io0-f196.google.com ([209.85.223.196]:36423 "EHLO mail-io0-f196.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751563AbdF3J7B (ORCPT ); Fri, 30 Jun 2017 05:59:01 -0400 MIME-Version: 1.0 In-Reply-To: <20170630093422.om7b75q5wyuby6r7@flea> References: <20170627143652.13075-1-net147@gmail.com> <20170628092024.ejxy6itqj3hx6yew@flea> <20170629155620.4keqi4cumbtvv63u@flea> <20170630093422.om7b75q5wyuby6r7@flea> From: Jonathan Liu Date: Fri, 30 Jun 2017 19:58:55 +1000 Message-ID: Subject: Re: [PATCH v5] drm/sun4i: hdmi: Implement I2C adapter for A10s DDC bus To: Maxime Ripard Cc: David Airlie , Chen-Yu Tsai , linux-kernel , dri-devel , linux-arm-kernel , linux-sunxi Content-Type: text/plain; charset="UTF-8" Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 3692 Lines: 96 Hi Maxime, On 30 June 2017 at 19:34, Maxime Ripard wrote: > Hi, > > On Fri, Jun 30, 2017 at 08:22:13AM +1000, Jonathan Liu wrote: >> Hi Maxime, >> >> On 30 June 2017 at 01:56, Maxime Ripard >> wrote: >> > On Wed, Jun 28, 2017 at 08:39:33PM +1000, Jonathan Liu wrote: >> >> >> + u32 int_status; >> >> >> + u32 fifo_status; >> >> >> + /* Read needs empty flag unset, write needs full flag unset */ >> >> >> + u32 flag = read ? SUN4I_HDMI_DDC_FIFO_STATUS_EMPTY : >> >> >> + SUN4I_HDMI_DDC_FIFO_STATUS_FULL; >> >> >> + int ret; >> >> >> + >> >> >> + /* Wait until error or FIFO ready */ >> >> >> + ret = readl_poll_timeout(hdmi->base + SUN4I_HDMI_DDC_INT_STATUS_REG, >> >> >> + int_status, >> >> >> + is_err_status(int_status) || >> >> >> + is_fifo_flag_unset(hdmi, &fifo_status, flag), >> >> >> + min(len, SUN4I_HDMI_DDC_FIFO_SIZE) * byte_time, >> >> >> + 100000); >> >> >> + >> >> >> + if (is_err_status(int_status)) >> >> >> + return -EIO; >> >> >> + if (ret) >> >> >> + return -ETIMEDOUT; >> >> > >> >> > Why not just have >> >> > ret = readl_poll_timeout(hdmi->base + SUN4I_HDMI_DDC_FIFO_STATUS_REG, reg, >> >> > !(reg & flag), 100, 100000); >> >> > >> >> > if (ret < 0) >> >> > if (is_err_status()) >> >> > return -EIO; >> >> > return ret; >> >> > >> >> > >> >> >> >> If I check error status after readl_poll_timeout and there is an error >> >> (e.g. the I2C address does not have a corresponding device connected >> >> or nothing connected to HDMI port) it will keep checking the fifo >> >> status even though error bit is set in the int status and then timeout >> >> after 100 ms. If it checks the int status register at the same time, >> >> it will error after 100 nanoseconds. I don't want to introduce >> >> unnecessary delays considering part of the reason for adding this >> >> driver to make it more usable for non-standard use cases. >> > >> > Well, polling for 100ms doesn't seem great either. What was the >> > rationale behind that timeout? >> > >> >> When an error occurs one of the error bits will be set in the >> INT_STATUS register so this is detected very quickly if I check the >> INT_STATUS and FIFO_STATUS at the same time. The 100 ms timeout is in >> case the I2C slave does clock stretching in which case the transfer >> may take longer than the predicted time. > > 100ms isn't stretching anymore, it's worse than that. > What would you suggest? >> > And we can also reverse the check and look at the INT_STATUS >> > register. The errors will be there, and we can program the threshold >> > we want in both directions and use the >> > DDC_FIFO_Request_Interrupt_Status bit. >> > >> >> I did try that when I was doing the v3 patch but I couldn't get it to >> work as mentioned previously in the v3 patch discussion. I programmed >> the FIFO_RX_TRIGGER_THRES and FIFO_TX_TRIGGER_THRES in DDC_FIFO_Ctrl >> register at the same time as setting FIFO_Address_Clear but the >> request interrupt status bit did not get updated to the appropriate >> state that is consistent with the FIFO level and the thresholds. I did >> try this several times for subsequent patch versions without success. > > What values did you set it to? > FIFO_RX_TRIGGER_THRES: 0 FIFO_TX_TRIGGER_THRES: 15 > Maxime > > -- > Maxime Ripard, Free Electrons > Embedded Linux and Kernel engineering > http://free-electrons.com Regards, Jonathan