From: Christopher Bostic <cbostic@linux.vnet.ibm.com>
To: wim@iguana.be, linux@roeck-us.net, robh+dt@kernel.org,
        mark.rutland@arm.com, joel@jms.id.au, linux-watchdog@vger.kernel.org,
        devicetree@vger.kernel.org
Cc: Christopher Bostic <cbostic@linux.vnet.ibm.com>,
        linux-kernel@vger.kernel.org, openbmc@lists.ozlabs.org
Subject: [PATCH v4 1/2] drivers/watchdog: Add optional ASPEED device tree properties
Date: Thu,  6 Jul 2017 19:48:59 -0500
In-Reply-To: <20170707004901.26780-1-cbostic@linux.vnet.ibm.com>
References: <20170707004901.26780-1-cbostic@linux.vnet.ibm.com>
Message-Id: <20170707004901.26780-2-cbostic@linux.vnet.ibm.com>
Sender: linux-kernel-owner@vger.kernel.org
Content-Length: 2943
Lines: 81

Describe device tree optional properties:

  * aspeed,reset-type = "cpu|soc|system|none"
     One of three different, mutually exclusive, values

	"cpu" : ARM CPU reset on signal
	"soc" : 'System on chip' reset
	"system" : Full system reset

     The value can also be set to "none" which indicates that no
     reset of any kind is to be done via this watchdog.  This assumes
     another watchdog on the chip is to take care of resets.

  * aspeed,interrupt - Interrupt CPU on signal
  * aspeed,external-signal - Generate external signal (WDT1 and WDT2 only)
  * aspeed,alt-boot - Boot from alternate block on signal

Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
---
v4 - Add aspeed-reset-type and assign one of four values,
     cpu, soc, system, none.
v3 - Invert soc and sys reset to 'no' to preserve backwards
     compatibility.  SOC and SYS reset will be set by default
     without any optional parameters set
v2 - Add 'aspeed,' prefix to all optional properties
   - Add arm-reset, soc-reset, interrupt, alt-boot properties
---
 .../devicetree/bindings/watchdog/aspeed-wdt.txt    | 35 ++++++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt
index c5e74d7..f526b00 100644
--- a/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/aspeed-wdt.txt
@@ -8,9 +8,44 @@ Required properties:
  - reg: physical base address of the controller and length of memory mapped
    region
 
+Optional properties:
+
+ - aspeed,reset-type = "cpu|soc|system|none"
+
+   Reset behavior - Whenever a timeout occurs the watchdog can be programmed
+   to generate one of three different, mutually exclusive, types of resets.
+
+   Type "none" can be specified to indicate that no resets are to be done.
+   This is useful in situations where another watchdog engine on chip is
+   to perform the reset.
+
+   If 'aspeed,reset-type=' is not specfied the default is to enable system
+   reset.
+
+   Reset types:
+
+        - cpu: Reset CPU on watchdog timeout
+
+        - soc: Reset 'System on Chip' on watchdog timeout
+
+        - system: Reset system on watchdog timeout
+
+        - none: No reset is performed on timeout. Assumes another watchdog
+                engine is responsible for this.
+
+ - aspeed,interrupt:	If property is present then interrupt CPU.
+			If not specified then don't interrupt CPU.
+
+ - aspeed,external-signal: If property is present then signal is sent to
+			external reset counter (only WDT1 and WDT2). If not
+			specified no external signal is sent.
+ - aspeed,alt-boot:    If property is present then boot from alternate block.
+
 Example:
 
 	wdt1: watchdog@1e785000 {
 		compatible = "aspeed,ast2400-wdt";
 		reg = <0x1e785000 0x1c>;
+		aspeed,reset-type = "system";
+		aspeed,external-signal;
 	};
-- 
1.8.2.2