Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1752874AbdHKLj4 (ORCPT ); Fri, 11 Aug 2017 07:39:56 -0400 Received: from smtp.codeaurora.org ([198.145.29.96]:53846 "EHLO smtp.codeaurora.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752169AbdHKLjw (ORCPT ); Fri, 11 Aug 2017 07:39:52 -0400 DMARC-Filter: OpenDMARC Filter v1.3.2 smtp.codeaurora.org 3C4BF60311 Authentication-Results: pdx-caf-mail.web.codeaurora.org; dmarc=none (p=none dis=none) header.from=codeaurora.org Authentication-Results: pdx-caf-mail.web.codeaurora.org; spf=none smtp.mailfrom=absahu@codeaurora.org From: Abhishek Sahu To: boris.brezillon@free-electrons.com Cc: dwmw2@infradead.org, computersforpeace@gmail.com, marek.vasut@gmail.com, richard@nod.at, cyrille.pitchen@wedev4u.fr, linux-arm-msm@vger.kernel.org, linux-kernel@vger.kernel.org, linux-mtd@lists.infradead.org, devicetree@vger.kernel.org, andy.gross@linaro.org, architt@codeaurora.org, sricharan@codeaurora.org, Abhishek Sahu , stable@vger.kernel.org Subject: [PATCH v4 01/20] mtd: nand: qcom: fix read failure without complete bootchain Date: Fri, 11 Aug 2017 17:09:16 +0530 Message-Id: <1502451575-15712-2-git-send-email-absahu@codeaurora.org> X-Mailer: git-send-email 1.9.1 In-Reply-To: <1502451575-15712-1-git-send-email-absahu@codeaurora.org> References: <1502451575-15712-1-git-send-email-absahu@codeaurora.org> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 2638 Lines: 74 The NAND page read fails without complete boot chain since NAND_DEV_CMD_VLD value is not proper. The default power on reset value for this register is 0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID The READ_START_VALID should be enabled for sending PAGE_READ command. READ_STOP_VALID should be cleared since normal NAND page read does not require READ_STOP command. Fixes: c76b78d8ec05a ("mtd: nand: Qualcomm NAND controller driver") Cc: stable@vger.kernel.org Reviewed-by: Archit Taneja Signed-off-by: Abhishek Sahu --- drivers/mtd/nand/qcom_nandc.c | 16 ++++++++++++---- 1 file changed, 12 insertions(+), 4 deletions(-) diff --git a/drivers/mtd/nand/qcom_nandc.c b/drivers/mtd/nand/qcom_nandc.c index 0e727d7..e5cb8f1 100644 --- a/drivers/mtd/nand/qcom_nandc.c +++ b/drivers/mtd/nand/qcom_nandc.c @@ -109,7 +109,11 @@ #define READ_ADDR 0 /* NAND_DEV_CMD_VLD bits */ -#define READ_START_VLD 0 +#define READ_START_VLD BIT(0) +#define READ_STOP_VLD BIT(1) +#define WRITE_START_VLD BIT(2) +#define ERASE_START_VLD BIT(3) +#define SEQ_READ_START_VLD BIT(4) /* NAND_EBI2_ECC_BUF_CFG bits */ #define NUM_STEPS 0 @@ -148,6 +152,10 @@ #define FETCH_ID 0xb #define RESET_DEVICE 0xd +/* Default Value for NAND_DEV_CMD_VLD */ +#define NAND_DEV_CMD_VLD_VAL (READ_START_VLD | WRITE_START_VLD | \ + ERASE_START_VLD | SEQ_READ_START_VLD) + /* * the NAND controller performs reads/writes with ECC in 516 byte chunks. * the driver calls the chunks 'step' or 'codeword' interchangeably @@ -695,8 +703,7 @@ static int nandc_param(struct qcom_nand_host *host) /* configure CMD1 and VLD for ONFI param probing */ nandc_set_reg(nandc, NAND_DEV_CMD_VLD, - (nandc->vld & ~(1 << READ_START_VLD)) - | 0 << READ_START_VLD); + (nandc->vld & ~READ_START_VLD)); nandc_set_reg(nandc, NAND_DEV_CMD1, (nandc->cmd1 & ~(0xFF << READ_ADDR)) | NAND_CMD_PARAM << READ_ADDR); @@ -1995,13 +2002,14 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc) { /* kill onenand */ nandc_write(nandc, SFLASHC_BURST_CFG, 0); + nandc_write(nandc, NAND_DEV_CMD_VLD, NAND_DEV_CMD_VLD_VAL); /* enable ADM DMA */ nandc_write(nandc, NAND_FLASH_CHIP_SELECT, DM_EN); /* save the original values of these registers */ nandc->cmd1 = nandc_read(nandc, NAND_DEV_CMD1); - nandc->vld = nandc_read(nandc, NAND_DEV_CMD_VLD); + nandc->vld = NAND_DEV_CMD_VLD_VAL; return 0; } -- QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation