Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753508AbdLDKfK (ORCPT ); Mon, 4 Dec 2017 05:35:10 -0500 Received: from laurent.telenet-ops.be ([195.130.137.89]:39242 "EHLO laurent.telenet-ops.be" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1753400AbdLDKfG (ORCPT ); Mon, 4 Dec 2017 05:35:06 -0500 From: Geert Uytterhoeven To: "David S . Miller" , Andrew Lunn , Florian Fainelli , Simon Horman , Magnus Damm Cc: Sergei Shtylyov , Rob Herring , Mark Rutland , Nicolas Ferre , Richard Leitner , netdev@vger.kernel.org, devicetree@vger.kernel.org, linux-renesas-soc@vger.kernel.org, linux-kernel@vger.kernel.org, Geert Uytterhoeven Subject: [PATCH v4 3/4] arm64: dts: renesas: salvator-common: Add EthernetAVB PHY reset Date: Mon, 4 Dec 2017 11:34:51 +0100 Message-Id: <1512383692-14009-4-git-send-email-geert+renesas@glider.be> X-Mailer: git-send-email 2.7.4 In-Reply-To: <1512383692-14009-1-git-send-email-geert+renesas@glider.be> References: <1512383692-14009-1-git-send-email-geert+renesas@glider.be> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 1562 Lines: 46 Describe the GPIO used to reset the Ethernet PHY for EthernetAVB. This allows the driver to reset the PHY during probe and after system resume. This fixes Ethernet operation after resume from s2ram on Salvator-XS, where the enable pin of the regulator providing PHY power is connected to PRESETn, and PSCI powers down the SoC during system suspend. On Salvator-X, the enable pin is always pulled high, but the driver may still need to reset the PHY if this wasn't done by the bootloader before. Inspired by patches in the BSP for the individual Salvator-X/XS boards by Kazuya Mizuguchi. Signed-off-by: Geert Uytterhoeven --- For proper PHY reset operation during system resume, this depends on "[PATCH v4 1/4] phylib: Add device reset GPIO support". However, this patch can be applied independently. v4: - No changes, v3: - Extract from series "[PATCH 0/4] ravb: Add PHY reset support", and incorporate in this series, - Move reset-gpios from the ethernet to the ethernet-phy node. --- arch/arm64/boot/dts/renesas/salvator-common.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi index a298df74ca6c037f..6a9524ff881306cf 100644 --- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi +++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi @@ -264,6 +264,7 @@ reg = <0>; interrupt-parent = <&gpio2>; interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; }; }; -- 2.7.4