Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753850AbdL1N7k (ORCPT ); Thu, 28 Dec 2017 08:59:40 -0500 Received: from outils.crapouillou.net ([89.234.176.41]:47552 "EHLO crapouillou.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1753589AbdL1N45 (ORCPT ); Thu, 28 Dec 2017 08:56:57 -0500 From: Paul Cercueil To: Ralf Baechle , Rob Herring , Michael Turquette Cc: Mark Rutland , Stephen Boyd , Maarten ter Huurne , devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-mips@linux-mips.org, linux-clk@vger.kernel.org, Paul Burton Subject: [PATCH v4 07/15] MIPS: Setup boot_command_line before plat_mem_setup Date: Thu, 28 Dec 2017 14:56:26 +0100 Message-Id: <20171228135634.30000-8-paul@crapouillou.net> In-Reply-To: <20171228135634.30000-1-paul@crapouillou.net> References: <20170702163016.6714-2-paul@crapouillou.net> <20171228135634.30000-1-paul@crapouillou.net> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 2886 Lines: 82 From: Paul Burton Platforms using DT will typically call __dt_setup_arch from plat_mem_setup. This in turn calls early_init_dt_scan. When CONFIG_CMDLINE is set, this leads to its value being copied into boot_command_line by early_init_dt_scan_chosen. If this happens before the code setting up boot_command_line in arch_mem_init runs, that code will go on to append CONFIG_CMDLINE (via builtin_cmdline) to boot_command_line again, duplicating it. For some command line parameters (eg. earlycon) this can be a problem. Set up boot_command_line before early_init_dt_scan_chosen gets called such that it will not write CONFIG_CMDLINE in this scenario & the arguments aren't duplicated. Signed-off-by: Paul Burton --- arch/mips/kernel/setup.c | 39 ++++++++++++++++++++------------------- 1 file changed, 20 insertions(+), 19 deletions(-) v2: New patch in this series v3: No change v4: No change diff --git a/arch/mips/kernel/setup.c b/arch/mips/kernel/setup.c index 702c678de116..85bc601e9a0d 100644 --- a/arch/mips/kernel/setup.c +++ b/arch/mips/kernel/setup.c @@ -826,25 +826,6 @@ static void __init arch_mem_init(char **cmdline_p) struct memblock_region *reg; extern void plat_mem_setup(void); - /* call board setup routine */ - plat_mem_setup(); - - /* - * Make sure all kernel memory is in the maps. The "UP" and - * "DOWN" are opposite for initdata since if it crosses over - * into another memory section you don't want that to be - * freed when the initdata is freed. - */ - arch_mem_addpart(PFN_DOWN(__pa_symbol(&_text)) << PAGE_SHIFT, - PFN_UP(__pa_symbol(&_edata)) << PAGE_SHIFT, - BOOT_MEM_RAM); - arch_mem_addpart(PFN_UP(__pa_symbol(&__init_begin)) << PAGE_SHIFT, - PFN_DOWN(__pa_symbol(&__init_end)) << PAGE_SHIFT, - BOOT_MEM_INIT_RAM); - - pr_info("Determined physical RAM map:\n"); - print_memory_map(); - #if defined(CONFIG_CMDLINE_BOOL) && defined(CONFIG_CMDLINE_OVERRIDE) strlcpy(boot_command_line, builtin_cmdline, COMMAND_LINE_SIZE); #else @@ -872,6 +853,26 @@ static void __init arch_mem_init(char **cmdline_p) } #endif #endif + + /* call board setup routine */ + plat_mem_setup(); + + /* + * Make sure all kernel memory is in the maps. The "UP" and + * "DOWN" are opposite for initdata since if it crosses over + * into another memory section you don't want that to be + * freed when the initdata is freed. + */ + arch_mem_addpart(PFN_DOWN(__pa_symbol(&_text)) << PAGE_SHIFT, + PFN_UP(__pa_symbol(&_edata)) << PAGE_SHIFT, + BOOT_MEM_RAM); + arch_mem_addpart(PFN_UP(__pa_symbol(&__init_begin)) << PAGE_SHIFT, + PFN_DOWN(__pa_symbol(&__init_end)) << PAGE_SHIFT, + BOOT_MEM_INIT_RAM); + + pr_info("Determined physical RAM map:\n"); + print_memory_map(); + strlcpy(command_line, boot_command_line, COMMAND_LINE_SIZE); *cmdline_p = command_line; -- 2.11.0