Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S933769AbeAKWur (ORCPT + 1 other); Thu, 11 Jan 2018 17:50:47 -0500 Received: from galahad.ideasonboard.com ([185.26.127.97]:59424 "EHLO galahad.ideasonboard.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S933341AbeAKWuo (ORCPT ); Thu, 11 Jan 2018 17:50:44 -0500 From: Laurent Pinchart To: Jacopo Mondi Cc: magnus.damm@gmail.com, geert@glider.be, mchehab@kernel.org, hverkuil@xs4all.nl, festevam@gmail.com, sakari.ailus@iki.fi, robh+dt@kernel.org, mark.rutland@arm.com, linux-renesas-soc@vger.kernel.org, linux-media@vger.kernel.org, linux-sh@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org Subject: Re: [PATCH v4 1/9] dt-bindings: media: Add Renesas CEU bindings Date: Fri, 12 Jan 2018 00:50:41 +0200 Message-ID: <3717276.fcpQzKB3PM@avalon> Organization: Ideas on Board Oy In-Reply-To: <1515515131-13760-2-git-send-email-jacopo+renesas@jmondi.org> References: <1515515131-13760-1-git-send-email-jacopo+renesas@jmondi.org> <1515515131-13760-2-git-send-email-jacopo+renesas@jmondi.org> MIME-Version: 1.0 Content-Transfer-Encoding: 7Bit Content-Type: text/plain; charset="us-ascii" Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Return-Path: Hi Jacopo, Thank you for the patch. On Tuesday, 9 January 2018 18:25:23 EET Jacopo Mondi wrote: > Add bindings documentation for Renesas Capture Engine Unit (CEU). > > Signed-off-by: Jacopo Mondi Reviewed-by: Laurent Pinchart > --- > .../devicetree/bindings/media/renesas,ceu.txt | 81 > ++++++++++++++++++++++ 1 file changed, 81 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/renesas,ceu.txt > > diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt > b/Documentation/devicetree/bindings/media/renesas,ceu.txt new file mode > 100644 > index 0000000..590ee27 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/renesas,ceu.txt > @@ -0,0 +1,81 @@ > +Renesas Capture Engine Unit (CEU) > +---------------------------------------------- > + > +The Capture Engine Unit is the image capture interface found in the Renesas > +SH Mobile and RZ SoCs. > + > +The interface supports a single parallel input with data bus width of 8 or > 16 +bits. > + > +Required properties: > +- compatible: Shall be "renesas,r7s72100-ceu" for CEU units found in > RZ/A1-H + and RZ/A1-M SoCs. > +- reg: Registers address base and size. > +- interrupts: The interrupt specifier. > + > +The CEU supports a single parallel input and should contain a single 'port' > +subnode with a single 'endpoint'. Connection to input devices are modeled > +according to the video interfaces OF bindings specified in: > +Documentation/devicetree/bindings/media/video-interfaces.txt > + > +Optional endpoint properties applicable to parallel input bus described in > +the above mentioned "video-interfaces.txt" file are supported. > + > +- hsync-active: Active state of the HSYNC signal, 0/1 for LOW/HIGH > respectively. + If property is not present, default is active high. > +- vsync-active: Active state of the VSYNC signal, 0/1 for LOW/HIGH > respectively. + If property is not present, default is active high. > + > +Example: > + > +The example describes the connection between the Capture Engine Unit and an > +OV7670 image sensor connected to i2c1 interface. > + > +ceu: ceu@e8210000 { > + reg = <0xe8210000 0x209c>; > + compatible = "renesas,r7s72100-ceu"; > + interrupts = ; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&vio_pins>; > + > + status = "okay"; > + > + port { > + ceu_in: endpoint { > + remote-endpoint = <&ov7670_out>; > + > + hsync-active = <1>; > + vsync-active = <0>; > + }; > + }; > +}; > + > +i2c1: i2c@fcfee400 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c1_pins>; > + > + status = "okay"; > + > + clock-frequency = <100000>; > + > + ov7670: camera@21 { > + compatible = "ovti,ov7670"; > + reg = <0x21>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&vio_pins>; > + > + reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>; > + powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>; > + > + port { > + ov7670_out: endpoint { > + remote-endpoint = <&ceu_in>; > + > + hsync-active = <1>; > + vsync-active = <0>; > + }; > + }; > + }; > +}; -- Regards, Laurent Pinchart