Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
From:   Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To:     Kieran Bingham <kbingham@kernel.org>
Cc:     linux-media@vger.kernel.org, dri-devel@lists.freedesktop.org,
        linux-kernel@vger.kernel.org, linux-renesas-soc@vger.kernel.org,
        Kieran Bingham <kieran.bingham@ideasonboard.com>,
        Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>,
        Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>,
        Lars-Peter Clausen <lars@metafoo.de>,
        Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>,
        Simon Horman <horms@verge.net.au>,
        Magnus Damm <magnus.damm@gmail.com>,
        Rob Herring <robh+dt@kernel.org>,
        Mark Rutland <mark.rutland@arm.com>,
        Russell King <linux@armlinux.org.uk>,
        "open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS" 
        <devicetree@vger.kernel.org>,
        "moderated list:ARM PORT" <linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH v3 3/5] [RFT] ARM: dts: wheat: Fix ADV7513 address usage
Date:   Tue, 13 Feb 2018 14:11:38 +0200
Message-ID: <5701429.SOn1uAbrAx@avalon>
Organization: Ideas on Board Oy
In-Reply-To: <1518473273-6333-4-git-send-email-kbingham@kernel.org>
References: <1518473273-6333-1-git-send-email-kbingham@kernel.org> <1518473273-6333-4-git-send-email-kbingham@kernel.org>
MIME-Version: 1.0
Content-Transfer-Encoding: 7Bit
Content-Type: text/plain; charset="us-ascii"
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

Hi Kieran,

Thank you for the patch.

On Tuesday, 13 February 2018 00:07:51 EET Kieran Bingham wrote:
> From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
> 
> The r8a7792 Wheat board has two ADV7513 devices sharing a single i2c
> bus, however in low power mode the ADV7513 will reset it's slave maps to
> use the hardware defined default addresses.
> 
> The ADV7511 driver was adapted to allow the two devices to be registered
> correctly - but it did not take into account the fault whereby the
> devices reset the addresses.
> 
> This results in an address conflict between the device using the default
> addresses, and the other device if it is in low-power-mode.
> 
> Repair this issue by moving both devices away from the default address
> definitions.
> 
> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
> v2:
>  - Addition to series
> 
> v3:
>  - Split map register addresses into individual declarations.
> 
>  arch/arm/boot/dts/r8a7792-wheat.dts | 12 ++++++++++--
>  1 file changed, 10 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/r8a7792-wheat.dts
> b/arch/arm/boot/dts/r8a7792-wheat.dts index b9471b67b728..42fff8837eab
> 100644
> --- a/arch/arm/boot/dts/r8a7792-wheat.dts
> +++ b/arch/arm/boot/dts/r8a7792-wheat.dts
> @@ -240,9 +240,16 @@
>  	status = "okay";
>  	clock-frequency = <400000>;
> 
> +	/*
> +	 * The adv75xx resets its addresses to defaults during low power power
> +	 * mode. Because we have two ADV7513 devices on the same bus, we must
> +	 * change both of them away from the defaults so that they do not
> +	 * conflict.
> +	 */
>  	hdmi@3d {
>  		compatible = "adi,adv7513";
> -		reg = <0x3d>;
> +		reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>;
> +		reg-names = "main", "cec", "edid", "packet";
> 
>  		adi,input-depth = <8>;
>  		adi,input-colorspace = "rgb";
> @@ -272,7 +279,8 @@
> 
>  	hdmi@39 {
>  		compatible = "adi,adv7513";
> -		reg = <0x39>;
> +		reg = <0x39>, <0x29>, <0x49>, <0x59>;
> +		reg-names = "main", "cec", "edid", "packet";
> 
>  		adi,input-depth = <8>;
>  		adi,input-colorspace = "rgb";

-- 
Regards,

Laurent Pinchart