Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
MIME-Version: 1.0
In-Reply-To: <1529479662-4026-2-git-send-email-absahu@codeaurora.org>
References: <1529479662-4026-1-git-send-email-absahu@codeaurora.org> <1529479662-4026-2-git-send-email-absahu@codeaurora.org>
From:   Masahiro Yamada <yamada.masahiro@socionext.com>
Date:   Mon, 25 Jun 2018 11:23:48 +0900
Message-ID: <CAK7LNAQirQO7MCsVa-MeSCj2J2_jW_2fV5HUAhss9pWHHAPNVg@mail.gmail.com>
Subject: Re: [PATCH v4 01/15] mtd: rawnand: helper function for setting up ECC configuration
To:     Abhishek Sahu <absahu@codeaurora.org>
Cc:     Boris Brezillon <boris.brezillon@bootlin.com>,
        Miquel Raynal <miquel.raynal@bootlin.com>,
        Archit Taneja <architt@codeaurora.org>,
        linux-arm-msm <linux-arm-msm@vger.kernel.org>,
        Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
        Marek Vasut <marek.vasut@gmail.com>,
        linux-mtd <linux-mtd@lists.infradead.org>,
        Richard Weinberger <richard@nod.at>,
        Andy Gross <andy.gross@linaro.org>,
        Brian Norris <computersforpeace@gmail.com>,
        David Woodhouse <dwmw2@infradead.org>
Content-Type: text/plain; charset="UTF-8"
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

2018-06-20 16:27 GMT+09:00 Abhishek Sahu <absahu@codeaurora.org>:
> commit 2c8f8afa7f92 ("mtd: nand: add generic helpers to check,
> match, maximize ECC settings") provides generic helpers which
> drivers can use for setting up ECC parameters.
>
> Since same board can have different ECC strength nand chips so
> following is the logic for setting up ECC strength and ECC step
> size, which can be used by most of the drivers.
>
> 1. If both ECC step size and ECC strength are already set
>    (usually by DT) then just check whether this setting
>    is supported by NAND controller.
> 2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength
>    supported by NAND controller.
> 3. Otherwise, try to match the ECC step size and ECC strength closest
>    to the chip's requirement. If available OOB size can't fit the chip
>    requirement then select maximum ECC strength which can be fit with
>    available OOB size.
>
> This patch introduces nand_ecc_choose_conf function which calls the
> required helper functions for the above logic. The drivers can use
> this single function instead of calling the 3 helper functions
> individually.
>
> CC: Masahiro Yamada <yamada.masahiro@socionext.com>

You can replace the CC with my

Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Thanks.


> Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
> ---
> * Changes from v3:
>   1. call nand_maximize_ecc() 2 times to make code more clear.
>
> * Changes from v2:
>
>   1. Renamed function to nand_ecc_choose_conf.
>   2. Minor code reorganization to remove warning and 2 function calls
>      for nand_maximize_ecc.
>
> * Changes from v1:
>   NEW PATCH
>
>  drivers/mtd/nand/raw/nand_base.c | 33 +++++++++++++++++++++++++++++++++
>  include/linux/mtd/rawnand.h      |  3 +++
>  2 files changed, 36 insertions(+)
>
> diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
> index 10c4f991..c64e3fc 100644
> --- a/drivers/mtd/nand/raw/nand_base.c
> +++ b/drivers/mtd/nand/raw/nand_base.c
> @@ -6287,6 +6287,39 @@ int nand_maximize_ecc(struct nand_chip *chip,
>  }
>  EXPORT_SYMBOL_GPL(nand_maximize_ecc);
>
> +/**
> + * nand_ecc_choose_conf - Set the ECC strength and ECC step size
> + * @chip: nand chip info structure
> + * @caps: ECC engine caps info structure
> + * @oobavail: OOB size that the ECC engine can use
> + *
> + * Choose the ECC configuration according to following logic
> + *
> + * 1. If both ECC step size and ECC strength are already set (usually by DT)
> + *    then check if it is supported by this controller.
> + * 2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength.
> + * 3. Otherwise, try to match the ECC step size and ECC strength closest
> + *    to the chip's requirement. If available OOB size can't fit the chip
> + *    requirement then fallback to the maximum ECC step size and ECC strength.
> + *
> + * On success, the chosen ECC settings are set.
> + */
> +int nand_ecc_choose_conf(struct nand_chip *chip,
> +                        const struct nand_ecc_caps *caps, int oobavail)
> +{
> +       if (chip->ecc.size && chip->ecc.strength)
> +               return nand_check_ecc_caps(chip, caps, oobavail);
> +
> +       if (chip->ecc.options & NAND_ECC_MAXIMIZE)
> +               return nand_maximize_ecc(chip, caps, oobavail);
> +
> +       if (!nand_match_ecc_req(chip, caps, oobavail))
> +               return 0;
> +
> +       return nand_maximize_ecc(chip, caps, oobavail);
> +}
> +EXPORT_SYMBOL_GPL(nand_ecc_choose_conf);
> +
>  /*
>   * Check if the chip configuration meet the datasheet requirements.
>
> diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h
> index 3e8ec3b..03a0061 100644
> --- a/include/linux/mtd/rawnand.h
> +++ b/include/linux/mtd/rawnand.h
> @@ -1650,6 +1650,9 @@ int nand_match_ecc_req(struct nand_chip *chip,
>  int nand_maximize_ecc(struct nand_chip *chip,
>                       const struct nand_ecc_caps *caps, int oobavail);
>
> +int nand_ecc_choose_conf(struct nand_chip *chip,
> +                        const struct nand_ecc_caps *caps, int oobavail);
> +
>  /* Default write_oob implementation */
>  int nand_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip, int page);
>
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc.
> is a member of Code Aurora Forum, hosted by The Linux Foundation
>
>
> ______________________________________________________
> Linux MTD discussion mailing list
> http://lists.infradead.org/mailman/listinfo/linux-mtd/


-- 
Best Regards
Masahiro Yamada