Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
Date:   Mon, 5 Nov 2018 12:02:19 +0100
From:   Boris Brezillon <boris.brezillon@bootlin.com>
To:     Piotr Bugalski <bugalski.piotr@gmail.com>
Cc:     Mark Brown <broonie@kernel.org>, linux-spi@vger.kernel.org,
        David Woodhouse <dwmw2@infradead.org>,
        Brian Norris <computersforpeace@gmail.com>,
        Marek Vasut <marek.vasut@gmail.com>,
        Richard Weinberger <richard@nod.at>,
        linux-mtd@lists.infradead.org,
        linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org,
        devicetree@vger.kernel.org, Rob Herring <robh+dt@kernel.org>,
        Mark Rutland <mark.rutland@arm.com>,
        Nicolas Ferre <nicolas.ferre@microchip.com>,
        Alexandre Belloni <alexandre.belloni@bootlin.com>,
        Cyrille Pitchen <cyrille.pitchen@microchip.com>,
        Tudor Ambarus <tudor.ambarus@microchip.com>
Subject: Re: [PATCH v3 0/6] New QuadSPI driver for Atmel SAMA5D2
Message-ID: <20181105120219.03ab3b4c@bbrezillon>
In-Reply-To: <20181105103625.9644-1-bugalski.piotr@gmail.com>
References: <20181105103625.9644-1-bugalski.piotr@gmail.com>
MIME-Version: 1.0
Content-Type: text/plain; charset=US-ASCII
Content-Transfer-Encoding: 7bit
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

Hi Piotr,

On Mon,  5 Nov 2018 11:36:19 +0100
Piotr Bugalski <bugalski.piotr@gmail.com> wrote:

> Hello,
> 
> Atmel SAMA5D2 is equipped with two QSPI interfaces. These interfaces can
> work as in SPI-compatible mode or use two / four lines to improve
> communication speed. At the moment there is QSPI driver strongly tied to
> NOR-flash memory and MTD subsystem.
> Intention of this change is to provide new driver which will not be tied
> to MTD and allows using QSPI with NAND-flash memory or other peripherals
> New spi-mem API provides abstraction layer which can disconnect QSPI
> from MTD. This driver doesn't support regular SPI interface, it should
> be used with spi-mem interface only.
> Unfortunately SAMA5D2 hardware by default supports only NOR-flash
> memory. It allows 24- and 32-bit addressing while NAND-flash requires
> 16-bit long. To workaround hardware limitation driver is a bit more
> complicated.
> 
> Request to spi-mem contains three fiels: opcode (command), address,
> dummy bytes. SAMA5D2 QSPI hardware supports opcode, address, dummy and
> option byte where address field can only be 24- or 32- bytes long.
> Handling 8-bits long addresses is done using option field. For 16-bits
> address behaviour depends of number of requested dummy bits. If there
> are 8 or more dummy cycles, address is shifted and sent with first dummy
> byte. Otherwise opcode is disabled and first byte of address contains
> command opcode (works only if opcode and address use the same buswidth).
> The limitation is when 16-bit address is used without enough dummy
> cycles and opcode is using different buswidth than address. Other modes
> are supported with described workaround.
> 
> It looks like hardware has some limitation in performance. The same issue
> exists in current QSPI driver (MTD/nor-flash) and soft-pack (bare-metal
> library from Atmel). Without using DMA read speed is much worse than
> maximum bandwidth (efficiency 30-40%). Any help with performance
> improvement is highly welcome, especially for NAND-flash memories which
> offers higher capacity than NOR-flash used with previous driver.

I think you can try to implement the dirmap interface proposed here [1]
and use DMA+TRSFR_READ/WRITE_MEMORY for such direct mappings. This
should optimize path where we really matter about perfs.

> 
> Best Regards,
> Piotr
> 
> v3 changes:
>  - add get_name implementation
>  - email address fix
> 
> v2 changes:
>  - driver is now replacement of existing atmel-quadspi
>  - code was re-written to follow original code structure
>  - deinitialization order fixed
>  - empty atmel_qspi_adjust_op_size function removed
>  - code formatting fixes
>  - use spi_device->max_speed_hz to get spi speed
>  - spi freqency set in spi_controller->setup() hook
>  - address range checkng for 4-bytes addressing
>  - use timeout to avoid infinite waiting
> 
> Piotr Bugalski (6):
>   mtd: spi-nor: atmel-quaspi: Typo fix
>   mtd: spi-nor: atmel-quadspi: Add spi-mem support to atmel-quadspi
>   mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi
>     driver
>   mtd: spi-nor: atmel-quadspi: Remove unused code from atmel-quadspi
>     driver
>   spi: Add QuadSPI driver for Atmel SAMA5D2
>   dt-bindings: spi: QuadSPI driver for Atmel SAMA5D2

The patch series is

Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>

Mark, if you're okay with the new implementation, would you mind taking
those patches in the spi tree?

Thanks,

Boris

[1]http://patchwork.ozlabs.org/project/linux-mtd/list/?series=73235