Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
Date:   Mon, 26 Nov 2018 10:11:16 +0100
From:   Lothar =?UTF-8?B?V2HDn21hbm4=?= <LW@KARO-electronics.de>
To:     Uwe =?UTF-8?B?S2xlaW5lLUvDtm5pZw==?= 
        <u.kleine-koenig@pengutronix.de>
Cc:     =?UTF-8?B?Vm9rw6HEjQ==?= Michal <Michal.Vokac@ysoft.com>,
        Thierry Reding <thierry.reding@gmail.com>,
        Mark Rutland <mark.rutland@arm.com>,
        "devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
        "linux-pwm@vger.kernel.org" <linux-pwm@vger.kernel.org>,
        Lukasz Majewski <l.majewski@majess.pl>,
        "linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
        Rob Herring <robh+dt@kernel.org>,
        "kernel@pengutronix.de" <kernel@pengutronix.de>,
        Fabio Estevam <fabio.estevam@nxp.com>,
        Linus Walleij <linus.walleij@linaro.org>,
        viresh kumar <viresh.kumar@linaro.org>
Subject: Re: [RCF PATCH,v2,2/2] pwm: imx: Configure output to GPIO in
 disabled state
Message-ID: <20181126101116.32819842@ipc1.ka-ro>
In-Reply-To: <20181125205612.aownvgjnpxhqyxed@pengutronix.de>
References: <20181114215120.vddykljqyavm64wj@pengutronix.de>
        <20181115152545.GA8611@ulmo>
        <20181115203733.qvonika6yhn2bsnb@pengutronix.de>
        <20181116083430.7f1d8452@ipc1.ka-ro>
        <20181116082557.l2ljgu3hsu7tvdci@pengutronix.de>
        <91640f9b-d219-553e-043a-c6151f2f68d7@ysoft.com>
        <20181122162359.ufngpgxkenlmgqni@pengutronix.de>
        <b332b319-cbb3-547f-c8b7-1dd275c1596d@ysoft.com>
        <20181122190321.ktqegs7kpvhcemvi@pengutronix.de>
        <9da8c6d9-d97c-200c-d8e4-2eb9f73eedc5@ysoft.com>
        <20181125205612.aownvgjnpxhqyxed@pengutronix.de>
Organization: Ka-Ro electronics GmbH
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8BIT
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

Uwe Kleine-König <u.kleine-koenig@pengutronix.de> wrote:

> Hello Michal,
> 
> On Fri, Nov 23, 2018 at 03:15:11PM +0000, Vokáč Michal wrote:
> > On 22.11.2018 20:03, Uwe Kleine-König wrote:  
> > > On Thu, Nov 22, 2018 at 04:46:39PM +0000, Vokáč Michal wrote:  
> > >> On 22.11.2018 17:23, Uwe Kleine-König wrote:  
> > >>> So I'd expect this to really work on i.MX6 but not the earlier SoCs
> > >>> without a gpio specifier.  
> > >>
> > >> Maybe you would expect it to work but I already tested and measured
> > >> that weeks ago ;) It did not work.  
> > > 
> > > Which pin/gpio do we talk about? Which i.MX6 variant did you test this
> > > on? (Assuming i.MX6D or i.MX6Q and PAD_DISP0_DATA09, did you try setting
> > > 
> > > 	IOMUXC_SW_MUX_CTL_PAD_DISP0_DATA09 (0x020E0194) = 0x00000005
> > > 	IOMUXC_SW_PAD_CTL_PAD_DISP0_DATA09 (0x020E04A8) = 0x0000b080
> > > 
> > > and then play with GPIO 4.30 direction and output value?)  
> > 
> > My test setup is as follows:
> > - SoC is i.MX6DL or i.MX6S - I have three board variants in total.
> > - Pin used for PWM/GPIO is PAD_GPIO9.
> > - The pin is not connected to any circuit. Just a test point.
> > - pinctrl setup in DT:
> >    - for "pwm":
> >      - fsl,pins = <MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8>
> >      - IOMUXC_SW_MUX_CTL_PAD_GPIO09 = 0x00000004
> >      - IOMUXC_SW_PAD_CTL_PAD_GPIO09 = 0x00000008
> > 
> >    - for "gpio":
> >     - fsl,pins = <MX6QDL_PAD_GPIO_9__GPIO1_IO09 0xb000>
> >     - IOMUXC_SW_MUX_CTL_PAD_GPIO09 = 0x00000005
> >     - IOMUXC_SW_PAD_CTL_PAD_GPIO09 = 0x0000b000  
> 
> FTR: I suggested 0x0000b080 here, but 0x0000b000 is just fine.
> 
> > Test scenario:
> > 
> > - In bootloader configure the pin as GPIO output, set it LOW (0V).
> >    I set it LOW to start in the oposite state than I want to end up in.
> > - Boot Linux
> > - Use sysfs to configure the PWM to produce some signal.
> > - In the PWM driver select the "pwm" pinctrl state.
> > - Measure the output - expected waveform on the scope.
> > - Use sysfs to stop the PWM "echo 0 > /sys/class/pwm/pwmchip0/pwm0/enable°
> > - In the PWM driver select the "gpio" pinctrl state.
> > - Then in the PWM driver:
> > 
> > a) non-working variant
> > - Do not request the GPIO - so do not touch its pad control reg.
> >    It is set as output from the bootloader, data register = 0.
> > - Measure voltage on the output
> >    - against GND = 0V
> >    - against VCC = 0V
> > - Measure resistance against VCC: Hi-Z
> > 
> > The pin is in Hi-Z mode. That is fine but that does not satisfy any
> > logic level.
> > 
> > b) working variant
> > - Request the GPIO, configure it as input.
> > - Measure voltage on the output
> >    - against GND = VCC (3.3V)
> >    - against VCC = 0V
> > - Measure resistance against VCC = 91.1kOhm
> > 
> > The pull-up is active.  
> 
> Thanks for your detailed test. So DSE = 0 doesn't work as I (and I think
> Lothar) expected.
> 
> @Lothar: if Michal did something different than you expected, please
> tell us with a few more details.
> 
No, Michal's findings are in sync with what I checked here.


Lothar Waßmann
-- 
___________________________________________________________

Ka-Ro electronics GmbH | Pascalstraße 22 | D - 52076 Aachen
Phone: +49 2408 1402-0 | Fax: +49 2408 1402-10
Geschäftsführer: Matthias Kaussen
Handelsregistereintrag: Amtsgericht Aachen, HRB 4996

www.karo-electronics.de | info@karo-electronics.de
___________________________________________________________