Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
Received-SPF: Pass (protection.outlook.com: domain of analog.com designates
 137.71.25.57 as permitted sender) receiver=protection.outlook.com;
 client-ip=137.71.25.57; helo=nwd2mta2.analog.com;
From:   Stefan Popa <stefan.popa@analog.com>
To:     <jic23@kernel.org>, <robh+dt@kernel.org>, <mark.rutland@arm.com>
CC:     Stefan Popa <stefan.popa@analog.com>,
        <Michael.Hennerich@analog.com>, <knaack.h@gmx.de>,
        <lars@metafoo.de>, <pmeerw@pmeerw.net>,
        <gregkh@linuxfoundation.org>, <linux-kernel@vger.kernel.org>,
        <linux-iio@vger.kernel.org>, <devel@driverdev.osuosl.org>,
        <stefan.popa@analog.co>
Subject: [PATCH 11/11] dt-bindings: iio: adc: Add docs for AD7606 ADC
Date:   Thu, 13 Dec 2018 14:46:23 +0200
Message-ID: <1544705183-13288-12-git-send-email-stefan.popa@analog.com>
In-Reply-To: <1544705183-13288-1-git-send-email-stefan.popa@analog.com>
References: <1544705183-13288-1-git-send-email-stefan.popa@analog.com>
MIME-Version: 1.0
Content-Type: text/plain; charset="UTF-8"
Content-Transfer-Encoding: 8bit
SpamDiagnosticOutput: 1:99
SpamDiagnosticMetadata: NSPM
X-MS-Exchange-CrossTenant-OriginalArrivalTime: 13 Dec 2018 12:47:47.5508
 (UTC)
X-MS-Exchange-CrossTenant-Network-Message-Id: 980ca74a-7212-4c45-df0a-08d660f92f57
X-MS-Exchange-CrossTenant-Id: eaa689b4-8f87-40e0-9c6f-7228de4d754a
X-MS-Exchange-CrossTenant-OriginalAttributedTenantConnectingIp: TenantId=eaa689b4-8f87-40e0-9c6f-7228de4d754a;Ip=[137.71.25.57];Helo=[nwd2mta2.analog.com]
X-MS-Exchange-CrossTenant-FromEntityHeader: HybridOnPrem
X-MS-Exchange-Transport-CrossTenantHeadersStamped: BL2PR03MB546
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk
List-ID: <linux-kernel.vger.kernel.org>
X-Mailing-List: linux-kernel@vger.kernel.org

Document support for AD7606 Analog to Digital Converter.

Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/iio/adc/adi,ad7606.txt     | 65 ++++++++++++++++++++++
 MAINTAINERS                                        |  1 +
 2 files changed, 66 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt

diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
new file mode 100644
index 0000000..d7b6241
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
@@ -0,0 +1,65 @@
+Analog Devices AD7606 Simultaneous Sampling ADC
+
+Required properties for the AD7606:
+
+- compatible: Must be one of
+	* "adi,ad7605-4"
+	* "adi,ad7606-8"
+	* "adi,ad7606-6"
+	* "adi,ad7606-4"
+- reg: SPI chip select number for the device
+- spi-max-frequency: Max SPI frequency to use
+	see: Documentation/devicetree/bindings/spi/spi-bus.txt
+- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
+- avcc-supply: phandle to the Avcc power supply
+- interrupts: IRQ line for the ADC
+	see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin.
+		  This logic input is used to initiate conversions on the analog
+		  input channels. As the line is active high, it should be marked
+		  GPIO_ACTIVE_HIGH.
+
+Optional properties:
+
+- reset-gpios: must be the device tree identifier of the RESET pin. If specified,
+	       it will be asserted during driver probe. As the line is active high,
+	       it should be marked GPIO_ACTIVE_HIGH.
+- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used
+		to place the AD7606 into one of two power-down modes, Standby mode or
+		Shutdown mode. As the line is active low, it should be marked
+		GPIO_ACTIVE_LOW.
+- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin.
+		    The FRSTDATA output indicates when the first channel, V1, is
+		    being read back on either the parallel, byte or serial interface.
+		    As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
+- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on
+	      this pin determines the input range of the analog input channels. If
+	      this pin is tied to a logic high, the analog input range is ±10V for
+	      all channels. If this pin is tied to a logic low, the analog input range
+	      is ±5V for all channels. As the line is active high, it should be marked
+	      GPIO_ACTIVE_HIGH.
+- adi,oversampling-ratio-gpios: must be the device tree identifier of the over-sampling
+				mode pins. As the line is active high, it should be marked
+				GPIO_ACTIVE_HIGH.
+
+Example:
+
+	adc@0 {
+		compatible = "adi,ad7606-8";
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		spi-cpol;
+
+		avcc-supply = <&adc_vref>;
+
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpio>;
+
+		adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
+		adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+		adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH
+						&gpio 23 GPIO_ACTIVE_HIGH
+						&gpio 26 GPIO_ACTIVE_HIGH>;
+		standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
+	};
diff --git a/MAINTAINERS b/MAINTAINERS
index 7256ce6..798e9a2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -859,6 +859,7 @@ L:	linux-iio@vger.kernel.org
 W:	http://ez.analog.com/community/linux-device-drivers
 S:	Supported
 F:	drivers/iio/adc/ad7606.c
+F:	Documentation/devicetree/bindings/iio/adc/ad7606.txt
 
 ANALOG DEVICES INC AD9389B DRIVER
 M:	Hans Verkuil <hans.verkuil@cisco.com>
-- 
2.7.4