Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
From:   Andrey Smirnov <andrew.smirnov@gmail.com>
To:     Shawn Guo <shawnguo@kernel.org>
Cc:     Andrey Smirnov <andrew.smirnov@gmail.com>,
        Fabio Estevam <festevam@gmail.com>,
        Chris Healy <cphealy@gmail.com>, Andrew Lunn <andrew@lunn.ch>,
        Heiner Kallweit <hkallweit1@gmail.com>,
        Rob Herring <robh@kernel.org>, devicetree@vger.kernel.org,
        linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org,
        linux-imx@nxp.com
Subject: [PATCH v3 3/3] ARM: dts: vf610: Add ZII SPB4 board
Date:   Mon, 25 Mar 2019 11:22:43 -0700
Message-Id: <20190325182243.16788-3-andrew.smirnov@gmail.com>
In-Reply-To: <20190325182243.16788-1-andrew.smirnov@gmail.com>
References: <20190325182243.16788-1-andrew.smirnov@gmail.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

Add Device Tree for VF610 based Zodiac Seat Power Box.

Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-imx@nxp.com
---

Changes since [v2]:

    - Collected Reviewed-by from Fabio

    - Fixed whitespace problems

    - Added patches for DT schema

Changes since [v1]:

    - Change Makefile diff to keep entries in alphabetical order

    - Various node name changes


[v2] lkml.kernel.org/r/20190313070224.30124-1-andrew.smirnov@gmail.com
[v1] lkml.kernel.org/r/20190311184928.25988-1-andrew.smirnov@gmail.com


 arch/arm/boot/dts/Makefile           |   1 +
 arch/arm/boot/dts/vf610-zii-spb4.dts | 359 +++++++++++++++++++++++++++
 2 files changed, 360 insertions(+)
 create mode 100644 arch/arm/boot/dts/vf610-zii-spb4.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f4f5aeaf3298..efefce8efa05 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -606,6 +606,7 @@ dtb-$(CONFIG_SOC_VF610) += \
 	vf610-zii-dev-rev-b.dtb \
 	vf610-zii-dev-rev-c.dtb \
 	vf610-zii-scu4-aib.dtb \
+	vf610-zii-spb4.dtb \
 	vf610-zii-ssmb-dtu.dtb \
 	vf610-zii-ssmb-spu3.dtb
 dtb-$(CONFIG_ARCH_MXS) += \
diff --git a/arch/arm/boot/dts/vf610-zii-spb4.dts b/arch/arm/boot/dts/vf610-zii-spb4.dts
new file mode 100644
index 000000000000..9dde83ccb9d1
--- /dev/null
+++ b/arch/arm/boot/dts/vf610-zii-spb4.dts
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/*
+ * Device tree file for ZII's SPB4 board
+ *
+ * SPB - Seat Power Box
+ *
+ * Copyright (C) 2019 Zodiac Inflight Innovations
+ */
+
+/dts-v1/;
+#include "vf610.dtsi"
+
+/ {
+	model = "ZII VF610 SPB4 Board";
+	compatible = "zii,vf610spb4", "zii,vf610dev", "fsl,vf610";
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pinctrl_leds_debug>;
+		pinctrl-names = "default";
+
+		led-debug {
+			label = "zii:green:debug1";
+			gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_mcu";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&adc0 {
+	vref-supply = <&reg_vcc_3v3_mcu>;
+	status = "okay";
+};
+
+&adc1 {
+	vref-supply = <&reg_vcc_3v3_mcu>;
+	status = "okay";
+};
+
+&dspi1 {
+	bus-num = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_dspi1>;
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p128", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&edma0 {
+	status = "okay";
+};
+
+&edma1 {
+	status = "okay";
+};
+
+&esdhc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc0>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	no-sdio;
+	no-sd;
+	status = "okay";
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	bus-width = <4>;
+	no-sdio;
+	status = "okay";
+};
+
+&fec1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	status = "okay";
+
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+
+	mdio1: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		switch0: switch0@0 {
+			compatible = "marvell,mv88e6190";
+			pinctrl-0 = <&pinctrl_gpio_switch0>;
+			pinctrl-names = "default";
+			reg = <0>;
+			eeprom-length = <65536>;
+			reset-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&gpio3>;
+			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&fec1>;
+
+					fixed-link {
+						speed = <100>;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "eth_cu_1000_1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "eth_cu_1000_2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "eth_cu_1000_3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "eth_cu_1000_4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "eth_cu_1000_5";
+				};
+
+				port@6 {
+					reg = <6>;
+					label = "eth_cu_1000_6";
+				};
+			};
+		};
+	};
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c0>;
+	status = "okay";
+
+	io-expander@22 {
+		compatible = "nxp,pca9554";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		label = "nameplate";
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c04";
+		reg = <0x52>;
+	};
+};
+
+&snvsrtc {
+	status = "disabled";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+
+	rave-sp {
+		compatible = "zii,rave-sp-rdu2";
+		current-speed = <1000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		watchdog {
+			compatible = "zii,rave-sp-watchdog";
+		};
+
+		eeprom@a3 {
+			compatible = "zii,rave-sp-eeprom";
+			reg = <0xa3 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			zii,eeprom-name = "main-eeprom";
+		};
+	};
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&wdoga5 {
+       status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_dspi1: dspi1grp {
+		fsl,pins = <
+			VF610_PAD_PTD5__DSPI1_CS0		0x1182
+			VF610_PAD_PTD4__DSPI1_CS1		0x1182
+			VF610_PAD_PTC6__DSPI1_SIN		0x1181
+			VF610_PAD_PTC7__DSPI1_SOUT		0x1182
+			VF610_PAD_PTC8__DSPI1_SCK		0x1182
+		>;
+	};
+
+	pinctrl_esdhc0: esdhc0grp {
+		fsl,pins = <
+			VF610_PAD_PTC0__ESDHC0_CLK		0x31ef
+			VF610_PAD_PTC1__ESDHC0_CMD		0x31ef
+			VF610_PAD_PTC2__ESDHC0_DAT0		0x31ef
+			VF610_PAD_PTC3__ESDHC0_DAT1		0x31ef
+			VF610_PAD_PTC4__ESDHC0_DAT2		0x31ef
+			VF610_PAD_PTC5__ESDHC0_DAT3		0x31ef
+			VF610_PAD_PTD23__ESDHC0_DAT4		0x31ef
+			VF610_PAD_PTD22__ESDHC0_DAT5		0x31ef
+			VF610_PAD_PTD21__ESDHC0_DAT6		0x31ef
+			VF610_PAD_PTD20__ESDHC0_DAT7		0x31ef
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			VF610_PAD_PTA24__ESDHC1_CLK		0x31ef
+			VF610_PAD_PTA25__ESDHC1_CMD		0x31ef
+			VF610_PAD_PTA26__ESDHC1_DAT0		0x31ef
+			VF610_PAD_PTA27__ESDHC1_DAT1		0x31ef
+			VF610_PAD_PTA28__ESDHC1_DATA2		0x31ef
+			VF610_PAD_PTA29__ESDHC1_DAT3		0x31ef
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			VF610_PAD_PTA6__RMII_CLKIN		0x30d1
+			VF610_PAD_PTC9__ENET_RMII1_MDC		0x30d2
+			VF610_PAD_PTC10__ENET_RMII1_MDIO	0x30d3
+			VF610_PAD_PTC11__ENET_RMII1_CRS		0x30d1
+			VF610_PAD_PTC12__ENET_RMII1_RXD1	0x30d1
+			VF610_PAD_PTC13__ENET_RMII1_RXD0	0x30d1
+			VF610_PAD_PTC14__ENET_RMII1_RXER	0x30d1
+			VF610_PAD_PTC15__ENET_RMII1_TXD1	0x30d2
+			VF610_PAD_PTC16__ENET_RMII1_TXD0	0x30d2
+			VF610_PAD_PTC17__ENET_RMII1_TXEN	0x30d2
+		>;
+	};
+
+	pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
+		fsl,pins = <
+			VF610_PAD_PTE2__GPIO_107		0x31c2
+			VF610_PAD_PTB28__GPIO_98		0x219d
+		>;
+	};
+
+	pinctrl_i2c0: i2c0grp {
+		fsl,pins = <
+			VF610_PAD_PTB14__I2C0_SCL		0x37ff
+			VF610_PAD_PTB15__I2C0_SDA		0x37ff
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			VF610_PAD_PTB16__I2C1_SCL		0x37ff
+			VF610_PAD_PTB17__I2C1_SDA		0x37ff
+		>;
+	};
+
+	pinctrl_leds_debug: pinctrl-leds-debug {
+		fsl,pins = <
+			VF610_PAD_PTD3__GPIO_82			0x31c2
+		>;
+	};
+
+	pinctrl_uart0: uart0grp {
+		fsl,pins = <
+			VF610_PAD_PTB10__UART0_TX		0x21a2
+			VF610_PAD_PTB11__UART0_RX		0x21a1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			VF610_PAD_PTB23__UART1_TX		0x21a2
+			VF610_PAD_PTB24__UART1_RX		0x21a1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			VF610_PAD_PTD0__UART2_TX		0x21a2
+			VF610_PAD_PTD1__UART2_RX		0x21a1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			VF610_PAD_PTA30__UART3_TX		0x21a2
+			VF610_PAD_PTA31__UART3_RX		0x21a1
+		>;
+	};
+};
-- 
2.20.1