Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S261453AbUJXMM1 (ORCPT ); Sun, 24 Oct 2004 08:12:27 -0400 Received: (majordomo@vger.kernel.org) by vger.kernel.org id S261454AbUJXMM1 (ORCPT ); Sun, 24 Oct 2004 08:12:27 -0400 Received: from rproxy.gmail.com ([64.233.170.199]:40172 "EHLO rproxy.gmail.com") by vger.kernel.org with ESMTP id S261453AbUJXMIQ (ORCPT ); Sun, 24 Oct 2004 08:08:16 -0400 DomainKey-Signature: a=rsa-sha1; q=dns; c=nofws; s=beta; d=gmail.com; h=received:message-id:date:from:reply-to:to:subject:cc:mime-version:content-type:content-transfer-encoding; b=pfyrBDSug+sPK+zAzQdfx53sIPMF0xSeDdl1tqaoy+1zt8zLO99A+R7XoE8w0is8I7+m9Tbyl8gXJKOjS1vGGJe62QeR8bD9rLyr1H/sJZp5xmAf0cyXKajH6ijHfKzOyuPrPRKlwRcIs3JQVH3itc75hPSY0Iw3ChIk74bTJQc= Message-ID: <58cb370e04102405081d62bf40@mail.gmail.com> Date: Sun, 24 Oct 2004 14:08:15 +0200 From: Bartlomiej Zolnierkiewicz Reply-To: Bartlomiej Zolnierkiewicz To: torvalds@osdl.org Subject: [BK PATCHES] ide-2.6 update Cc: linux-ide@vger.kernel.org, linux-kernel@vger.kernel.org Mime-Version: 1.0 Content-Type: text/plain; charset=US-ASCII Content-Transfer-Encoding: 7bit Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 52371 Lines: 1645 Kill most of /proc/ide/ bloat. Please do a bk pull bk://bart.bkbits.net/ide-2.6 This will update the following files: drivers/ide/pci/aec62xx.c | 110 -------------------------- drivers/ide/pci/aec62xx.h | 2 drivers/ide/pci/atiixp.c | 118 ---------------------------- drivers/ide/pci/cs5520.c | 74 +----------------- drivers/ide/pci/cs5530.c | 58 -------------- drivers/ide/pci/hpt366.c | 72 ----------------- drivers/ide/pci/hpt366.h | 2 drivers/ide/pci/pdc202xx_new.c | 64 --------------- drivers/ide/pci/pdc202xx_new.h | 2 drivers/ide/pci/pdc202xx_old.c | 130 ------------------------------- drivers/ide/pci/pdc202xx_old.h | 37 --------- drivers/ide/pci/piix.c | 167 ---------------------------------------- drivers/ide/pci/piix.h | 4 drivers/ide/pci/sc1200.c | 65 --------------- drivers/ide/pci/serverworks.c | 168 ----------------------------------------- drivers/ide/pci/serverworks.h | 2 drivers/ide/pci/slc90e66.c | 111 --------------------------- 17 files changed, 12 insertions(+), 1174 deletions(-) through these ChangeSets: (04/10/23 1.2039) [ide] slc90e66: kill /proc/ide/slc90e66 Signed-off-by: Bartlomiej Zolnierkiewicz (04/10/23 1.2038) [ide] serverworks: kill /proc/ide/svwks Signed-off-by: Bartlomiej Zolnierkiewicz (04/10/23 1.2037) [ide] sc1200: kill /proc/ide/sc1200 Signed-off-by: Bartlomiej Zolnierkiewicz (04/10/23 1.2036) [ide] piix: kill /proc/ide/piix Signed-off-by: Bartlomiej Zolnierkiewicz (04/10/23 1.2035) [ide] pdc202xx_old: kill /proc/ide/pdc202xx Signed-off-by: Bartlomiej Zolnierkiewicz (04/10/23 1.2034) [ide] pdc202xx_new: kill /proc/ide/pdcnew Signed-off-by: Bartlomiej Zolnierkiewicz (04/10/23 1.2033) [ide] hpt366: kill /proc/ide/hpt366 Signed-off-by: Bartlomiej Zolnierkiewicz (04/10/23 1.2032) [ide] cs5530: kill /proc/ide/cs5530 Signed-off-by: Bartlomiej Zolnierkiewicz (04/10/23 1.2031) [ide] cs5520: kill /proc/ide/cs5520 Signed-off-by: Bartlomiej Zolnierkiewicz (04/10/23 1.2030) [ide] atiixp: kill /proc/ide/atiixp Signed-off-by: Bartlomiej Zolnierkiewicz (04/10/23 1.2029) [ide] aec62xx: kill /proc/ide/aec62xx Signed-off-by: Bartlomiej Zolnierkiewicz diff -Nru a/drivers/ide/pci/aec62xx.c b/drivers/ide/pci/aec62xx.c --- a/drivers/ide/pci/aec62xx.c 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/aec62xx.c 2004-10-23 23:29:01 +02:00 @@ -18,52 +18,7 @@ #include "aec62xx.h" -#if defined(DISPLAY_AEC62XX_TIMINGS) && defined(CONFIG_PROC_FS) -#include -#include - -static u8 aec62xx_proc = 0; - -#define AEC_MAX_DEVS 5 - -static struct pci_dev *aec_devs[AEC_MAX_DEVS]; -static int n_aec_devs; - -static int aec62xx_get_info (char *buffer, char **addr, off_t offset, int count) -{ - char *p = buffer; - char *chipset_nums[] = {"error", "error", "error", "error", - "error", "error", "850UF", "860", - "860R", "865", "865R", "error" }; - int len; - int i; - - for (i = 0; i < n_aec_devs; i++) { - struct pci_dev *dev = aec_devs[i]; - unsigned long iobase = pci_resource_start(dev, 4); - u8 c0 = 0, c1 = 0, art = 0; - - c0 = inb(iobase + 0x02); - c1 = inb(iobase + 0x0a); - - p += sprintf(p, "\nController: %d\n", i); - p += sprintf(p, "Chipset: AEC%s\n", chipset_nums[dev->device]); - - p += sprintf(p, "--------------- Primary Channel " - "---------------- Secondary Channel " - "-------------\n"); - (void) pci_read_config_byte(dev, 0x4a, &art); - p += sprintf(p, " %sabled ", - (art&0x02)?" en":"dis"); - p += sprintf(p, " %sabled\n", - (art&0x04)?" en":"dis"); - p += sprintf(p, "--------------- drive0 --------- drive1 " - "-------- drive0 ---------- drive1 ------\n"); - p += sprintf(p, "DMA enabled: %s %s ", - (c0&0x20)?"yes":"no ",(c0&0x40)?"yes":"no "); - p += sprintf(p, " %s %s\n", - (c1&0x20)?"yes":"no ",(c1&0x40)?"yes":"no "); - +#if 0 if (dev->device == PCI_DEVICE_ID_ARTOP_ATP850UF) { (void) pci_read_config_byte(dev, 0x54, &art); p += sprintf(p, "DMA Mode: %s(%s)", @@ -79,59 +34,7 @@ (c1&0x40)?((art&0xc0)?"UDMA":" DMA"):" PIO", (art&0x80)?"2":(art&0x40)?"1":"0"); } else { - /* - * case PCI_DEVICE_ID_ARTOP_ATP860: - * case PCI_DEVICE_ID_ARTOP_ATP860R: - * case PCI_DEVICE_ID_ARTOP_ATP865: - * case PCI_DEVICE_ID_ARTOP_ATP865R: - */ - (void) pci_read_config_byte(dev, 0x44, &art); - p += sprintf(p, "DMA Mode: %s(%s)", - (c0&0x20)?((art&0x07)?"UDMA":" DMA"):" PIO", - ((art&0x07)==0x07)?"6": - ((art&0x06)==0x06)?"5": - ((art&0x05)==0x05)?"4": - ((art&0x04)==0x04)?"3": - ((art&0x03)==0x03)?"2": - ((art&0x02)==0x02)?"1": - ((art&0x01)==0x01)?"0":"?"); - p += sprintf(p, " %s(%s)", - (c0&0x40)?((art&0x70)?"UDMA":" DMA"):" PIO", - ((art&0x70)==0x70)?"6": - ((art&0x60)==0x60)?"5": - ((art&0x50)==0x50)?"4": - ((art&0x40)==0x40)?"3": - ((art&0x30)==0x30)?"2": - ((art&0x20)==0x20)?"1": - ((art&0x10)==0x10)?"0":"?"); - (void) pci_read_config_byte(dev, 0x45, &art); - p += sprintf(p, " %s(%s)", - (c1&0x20)?((art&0x07)?"UDMA":" DMA"):" PIO", - ((art&0x07)==0x07)?"6": - ((art&0x06)==0x06)?"5": - ((art&0x05)==0x05)?"4": - ((art&0x04)==0x04)?"3": - ((art&0x03)==0x03)?"2": - ((art&0x02)==0x02)?"1": - ((art&0x01)==0x01)?"0":"?"); - p += sprintf(p, " %s(%s)\n", - (c1&0x40)?((art&0x70)?"UDMA":" DMA"):" PIO", - ((art&0x70)==0x70)?"6": - ((art&0x60)==0x60)?"5": - ((art&0x50)==0x50)?"4": - ((art&0x40)==0x40)?"3": - ((art&0x30)==0x30)?"2": - ((art&0x20)==0x20)?"1": - ((art&0x10)==0x10)?"0":"?"); - } - } - /* p - buffer must be less than 4k! */ - len = (p - buffer) - offset; - *addr = buffer + offset; - - return len > count ? count : len; -} -#endif /* defined(DISPLAY_AEC62xx_TIMINGS) && defined(CONFIG_PROC_FS) */ +#endif /* * TO DO: active tuning and correction of cards without a bios. @@ -374,15 +277,6 @@ pci_write_config_dword(dev, PCI_ROM_ADDRESS, dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE); printk(KERN_INFO "%s: ROM enabled at 0x%08lx\n", name, dev->resource[PCI_ROM_RESOURCE].start); } - -#if defined(DISPLAY_AEC62XX_TIMINGS) && defined(CONFIG_PROC_FS) - aec_devs[n_aec_devs++] = dev; - - if (!aec62xx_proc) { - aec62xx_proc = 1; - ide_pci_create_host_proc("aec62xx", aec62xx_get_info); - } -#endif /* DISPLAY_AEC62XX_TIMINGS && CONFIG_PROC_FS */ if (bus_speed <= 33) pci_set_drvdata(dev, (void *) aec6xxx_33_base); diff -Nru a/drivers/ide/pci/aec62xx.h b/drivers/ide/pci/aec62xx.h --- a/drivers/ide/pci/aec62xx.h 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/aec62xx.h 2004-10-23 23:29:01 +02:00 @@ -5,8 +5,6 @@ #include #include -#define DISPLAY_AEC62XX_TIMINGS - struct chipset_bus_clock_list_entry { byte xfer_speed; byte chipset_settings; diff -Nru a/drivers/ide/pci/atiixp.c b/drivers/ide/pci/atiixp.c --- a/drivers/ide/pci/atiixp.c 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/atiixp.c 2004-10-23 23:29:01 +02:00 @@ -47,102 +47,6 @@ static int save_mdma_mode[4]; -#define DISPLAY_ATIIXP_TIMINGS - -#if defined(DISPLAY_ATIIXP_TIMINGS) && defined(CONFIG_PROC_FS) - -#include -#include - -static u8 atiixp_proc; -static struct pci_dev *bmide_dev; - -/** - * atiixp_get_info - fill in /proc for ATIIXP IDE - * @buffer: buffer to fill - * @addr: address of user start in buffer - * @offset: offset into 'file' - * @count: buffer count - * - * Output summary data on the tuning. - */ - -static int atiixp_get_info(char *buffer, char **addr, off_t offset, int count) -{ - char *p = buffer; - struct pci_dev *dev = bmide_dev; - unsigned long bibma = pci_resource_start(dev, 4); - u32 mdma_timing = 0; - u16 udma_mode = 0, pio_mode = 0; - u8 c0, c1, udma_control = 0; - - p += sprintf(p, "\n ATI "); - p += sprintf(p, "ATIIXP Ultra100 IDE Chipset.\n"); - - pci_read_config_byte(dev, ATIIXP_IDE_UDMA_CONTROL, &udma_control); - pci_read_config_word(dev, ATIIXP_IDE_UDMA_MODE, &udma_mode); - pci_read_config_word(dev, ATIIXP_IDE_PIO_MODE, &pio_mode); - pci_read_config_dword(dev, ATIIXP_IDE_MDMA_TIMING, &mdma_timing); - - /* - * at that point bibma+0x2 et bibma+0xa are byte registers - * to investigate: - */ - c0 = inb(bibma + 0x02); - c1 = inb(bibma + 0x0a); - - p += sprintf(p, "--------------- Primary Channel " - "---------------- Secondary Channel " - "-------------\n"); - p += sprintf(p, " %sabled " - " %sabled\n", - (c0 & 0x80) ? "dis" : " en", - (c1 & 0x80) ? "dis" : " en"); - p += sprintf(p, "--------------- drive0 --------- drive1 " - "-------- drive0 ---------- drive1 ------\n"); - p += sprintf(p, "DMA enabled: %s %s " - " %s %s\n", - (c0 & 0x20) ? "yes" : "no ", - (c0 & 0x40) ? "yes" : "no ", - (c1 & 0x20) ? "yes" : "no ", - (c1 & 0x40) ? "yes" : "no " ); - p += sprintf(p, "UDMA enabled: %s %s " - " %s %s\n", - (udma_control & 0x01) ? "yes" : "no ", - (udma_control & 0x02) ? "yes" : "no ", - (udma_control & 0x04) ? "yes" : "no ", - (udma_control & 0x08) ? "yes" : "no " ); - p += sprintf(p, "UDMA mode: %c %c " - " %c %c\n", - (udma_control & 0x01) ? - ((udma_mode & 0x07) + 48) : 'X', - (udma_control & 0x02) ? - (((udma_mode >> 4) & 0x07) + 48) : 'X', - (udma_control & 0x04) ? - (((udma_mode >> 8) & 0x07) + 48) : 'X', - (udma_control & 0x08) ? - (((udma_mode >> 12) & 0x07) + 48) : 'X'); - p += sprintf(p, "MDMA mode: %c %c " - " %c %c\n", - (save_mdma_mode[0] && (c0 & 0x20)) ? - ((save_mdma_mode[0] & 0xf) + 48) : 'X', - (save_mdma_mode[1] && (c0 & 0x40)) ? - ((save_mdma_mode[1] & 0xf) + 48) : 'X', - (save_mdma_mode[2] && (c1 & 0x20)) ? - ((save_mdma_mode[2] & 0xf) + 48) : 'X', - (save_mdma_mode[3] && (c1 & 0x40)) ? - ((save_mdma_mode[3] & 0xf) + 48) : 'X'); - p += sprintf(p, "PIO mode: %c %c " - " %c %c\n", - (c0 & 0x20) ? 'X' : ((pio_mode & 0x07) + 48), - (c0 & 0x40) ? 'X' : (((pio_mode >> 4) & 0x07) + 48), - (c1 & 0x20) ? 'X' : (((pio_mode >> 8) & 0x07) + 48), - (c1 & 0x40) ? 'X' : (((pio_mode >> 12) & 0x07) + 48)); - - return p - buffer; /* => must be less than 4k! */ -} -#endif /* defined(DISPLAY_ATIIXP_TIMINGS) && defined(CONFIG_PROC_FS) */ - /** * atiixp_ratemask - compute rate mask for ATIIXP IDE * @drive: IDE drive to compute for @@ -397,27 +301,6 @@ } /** - * init_chipset_atiixp - set up the ATIIXP chipset - * @dev: PCI device to set up - * @name: Name of the device - * - * Initialize the PCI device as required. For the ATIIXP this turns - * out to be nice and simple - */ - -static unsigned int __devinit init_chipset_atiixp(struct pci_dev *dev, const char *name) -{ -#if defined(DISPLAY_ATIIXP_TIMINGS) && defined(CONFIG_PROC_FS) - if (!atiixp_proc) { - atiixp_proc = 1; - bmide_dev = dev; - ide_pci_create_host_proc("atiixp", atiixp_get_info); - } -#endif /* DISPLAY_ATIIXP_TIMINGS && CONFIG_PROC_FS */ - return 0; -} - -/** * init_hwif_atiixp - fill in the hwif for the ATIIXP * @hwif: IDE interface * @@ -459,7 +342,6 @@ static ide_pci_device_t atiixp_pci_info[] __devinitdata = { { /* 0 */ .name = "ATIIXP", - .init_chipset = init_chipset_atiixp, .init_hwif = init_hwif_atiixp, .channels = 2, .autodma = AUTODMA, diff -Nru a/drivers/ide/pci/cs5520.c b/drivers/ide/pci/cs5520.c --- a/drivers/ide/pci/cs5520.c 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/cs5520.c 2004-10-23 23:29:01 +02:00 @@ -51,57 +51,6 @@ #include #include -#define DISPLAY_CS5520_TIMINGS - -#if defined(DISPLAY_CS5520_TIMINGS) && defined(CONFIG_PROC_FS) -#include -#include - -static u8 cs5520_proc = 0; -static struct pci_dev *bmide_dev; - -static int cs5520_get_info(char *buffer, char **addr, off_t offset, int count) -{ - char *p = buffer; - unsigned long bmiba = pci_resource_start(bmide_dev, 2); - int len; - u8 c0 = 0, c1 = 0; - u16 reg16; - u32 reg32; - - /* - * at that point bibma+0x2 et bibma+0xa are byte registers - * to investigate: - */ - c0 = inb(bmiba + 0x02); - c1 = inb(bmiba + 0x0a); - - p += sprintf(p, "\nCyrix CS55x0 IDE\n"); - p += sprintf(p, "--------------- Primary Channel " - "---------------- Secondary Channel " - "-------------\n"); - p += sprintf(p, " %sabled " - " %sabled\n", - (c0&0x80) ? "dis" : " en", - (c1&0x80) ? "dis" : " en"); - - p += sprintf(p, "\n\nTimings: \n"); - - pci_read_config_word(bmide_dev, 0x62, ®16); - p += sprintf(p, "8bit CAT/CRT : %04x\n", reg16); - pci_read_config_dword(bmide_dev, 0x64, ®32); - p += sprintf(p, "16bit Primary : %08x\n", reg32); - pci_read_config_dword(bmide_dev, 0x68, ®32); - p += sprintf(p, "16bit Secondary: %08x\n", reg32); - - len = (p - buffer) - offset; - *addr = buffer + offset; - - return len > count ? count : len; -} - -#endif - struct pio_clocks { int address; @@ -144,12 +93,14 @@ printk("PIO clocking = %d\n", pio); /* FIXME: if DMA = 1 do we need to set the DMA bit here ? */ - - /* 8bit command timing for channel */ + + /* 8bit CAT/CRT - 8bit command timing for channel */ pci_write_config_byte(pdev, 0x62 + controller, (cs5520_pio_clocks[pio].recovery << 4) | (cs5520_pio_clocks[pio].assert)); - + + /* 0x64 - 16bit Primary, 0x68 - 16bit Secondary */ + /* FIXME: should these use address ? */ /* Data read timing */ pci_write_config_byte(pdev, 0x64 + 4*controller + (drive->dn&1), @@ -188,19 +139,6 @@ /* Then tell the core to use DMA operations */ return hwif->ide_dma_on(drive); } - - -static unsigned int __devinit init_chipset_cs5520(struct pci_dev *dev, const char *name) -{ -#if defined(DISPLAY_CS5520_TIMINGS) && defined(CONFIG_PROC_FS) - if (!cs5520_proc) { - cs5520_proc = 1; - bmide_dev = dev; - ide_pci_create_host_proc("cs5520", cs5520_get_info); - } -#endif /* DISPLAY_CS5520_TIMINGS && CONFIG_PROC_FS */ - return 0; -} /* * We provide a callback for our nonstandard DMA location @@ -255,7 +193,6 @@ #define DECLARE_CS_DEV(name_str) \ { \ .name = name_str, \ - .init_chipset = init_chipset_cs5520, \ .init_setup_dma = cs5520_init_setup_dma, \ .init_hwif = init_hwif_cs5520, \ .channels = 2, \ @@ -294,7 +231,6 @@ printk(KERN_WARNING "cs5520: No suitable DMA available.\n"); return -ENODEV; } - init_chipset_cs5520(dev, d->name); index.all = 0xf0f0; diff -Nru a/drivers/ide/pci/cs5530.c b/drivers/ide/pci/cs5530.c --- a/drivers/ide/pci/cs5530.c 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/cs5530.c 2004-10-23 23:29:01 +02:00 @@ -31,56 +31,6 @@ #include #include -#define DISPLAY_CS5530_TIMINGS - -#if defined(DISPLAY_CS5530_TIMINGS) && defined(CONFIG_PROC_FS) -#include -#include - -static u8 cs5530_proc = 0; - -static struct pci_dev *bmide_dev; - -static int cs5530_get_info (char *buffer, char **addr, off_t offset, int count) -{ - char *p = buffer; - unsigned long bibma = pci_resource_start(bmide_dev, 4); - u8 c0 = 0, c1 = 0; - - /* - * at that point bibma+0x2 et bibma+0xa are byte registers - * to investigate: - */ - - c0 = inb_p((u16)bibma + 0x02); - c1 = inb_p((u16)bibma + 0x0a); - - p += sprintf(p, "\n " - "Cyrix 5530 Chipset.\n"); - p += sprintf(p, "--------------- Primary Channel " - "---------------- Secondary Channel " - "-------------\n"); - p += sprintf(p, " %sabled " - " %sabled\n", - (c0&0x80) ? "dis" : " en", - (c1&0x80) ? "dis" : " en"); - p += sprintf(p, "--------------- drive0 --------- drive1 " - "-------- drive0 ---------- drive1 ------\n"); - p += sprintf(p, "DMA enabled: %s %s " - " %s %s\n", - (c0&0x20) ? "yes" : "no ", - (c0&0x40) ? "yes" : "no ", - (c1&0x20) ? "yes" : "no ", - (c1&0x40) ? "yes" : "no " ); - - p += sprintf(p, "UDMA\n"); - p += sprintf(p, "DMA\n"); - p += sprintf(p, "PIO\n"); - - return p-buffer; -} -#endif /* DISPLAY_CS5530_TIMINGS && CONFIG_PROC_FS */ - /** * cs5530_xfer_set_mode - set a new transfer mode at the drive * @drive: drive to tune @@ -271,14 +221,6 @@ { struct pci_dev *master_0 = NULL, *cs5530_0 = NULL; unsigned long flags; - -#if defined(DISPLAY_CS5530_TIMINGS) && defined(CONFIG_PROC_FS) - if (!cs5530_proc) { - cs5530_proc = 1; - bmide_dev = dev; - ide_pci_create_host_proc("cs5530", cs5530_get_info); - } -#endif /* DISPLAY_CS5530_TIMINGS && CONFIG_PROC_FS */ dev = NULL; while ((dev = pci_find_device(PCI_VENDOR_ID_CYRIX, PCI_ANY_ID, dev)) != NULL) { diff -Nru a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c --- a/drivers/ide/pci/hpt366.c 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/hpt366.c 2004-10-23 23:29:01 +02:00 @@ -72,49 +72,6 @@ #include "hpt366.h" -#if defined(DISPLAY_HPT366_TIMINGS) && defined(CONFIG_PROC_FS) -#include -#include -#endif /* defined(DISPLAY_HPT366_TIMINGS) && defined(CONFIG_PROC_FS) */ - -static unsigned int hpt_revision(struct pci_dev *dev); -static unsigned int hpt_minimum_revision(struct pci_dev *dev, int revision); - -#if defined(DISPLAY_HPT366_TIMINGS) && defined(CONFIG_PROC_FS) - -static u8 hpt366_proc = 0; -static struct pci_dev *hpt_devs[HPT366_MAX_DEVS]; -static int n_hpt_devs; - -static int hpt366_get_info (char *buffer, char **addr, off_t offset, int count) -{ - char *p = buffer; - char *chipset_nums[] = {"366", "366", "368", - "370", "370A", "372", - "302", "371", "374" }; - int i, len; - - p += sprintf(p, "\n " - "HighPoint HPT366/368/370/372/374\n"); - for (i = 0; i < n_hpt_devs; i++) { - struct pci_dev *dev = hpt_devs[i]; - unsigned long iobase = dev->resource[4].start; - u32 class_rev = hpt_revision(dev); - u8 c0, c1; - - p += sprintf(p, "\nController: %d\n", i); - p += sprintf(p, "Chipset: HPT%s\n", chipset_nums[class_rev]); - p += sprintf(p, "--------------- Primary Channel " - "--------------- Secondary Channel " - "--------------\n"); - - /* get the bus master status registers */ - c0 = inb(iobase + 0x2); - c1 = inb(iobase + 0xa); - p += sprintf(p, "Enabled: %s" - " %s\n", - (c0 & 0x80) ? "no" : "yes", - (c1 & 0x80) ? "no" : "yes"); #if 0 if (hpt_minimum_revision(dev, 3)) { u8 cbl; @@ -128,16 +85,6 @@ (cbl & 0x01) ? 33 : 66); p += sprintf(p, "\n"); } -#endif - p += sprintf(p, "--------------- drive0 --------- drive1 " - "------- drive0 ---------- drive1 -------\n"); - p += sprintf(p, "DMA capable: %s %s" - " %s %s\n", - (c0 & 0x20) ? "yes" : "no ", - (c0 & 0x40) ? "yes" : "no ", - (c1 & 0x20) ? "yes" : "no ", - (c1 & 0x40) ? "yes" : "no "); - { u8 c2, c3; /* older revs don't have these registers mapped @@ -159,15 +106,7 @@ (c3 & 0x80) ? "PIO " : "off "); } } - p += sprintf(p, "\n"); - - /* p - buffer must be less than 4k! */ - len = (p - buffer) - offset; - *addr = buffer + offset; - - return len > count ? count : len; -} -#endif /* defined(DISPLAY_HPT366_TIMINGS) && defined(CONFIG_PROC_FS) */ +#endif static u32 hpt_revision (struct pci_dev *dev) { @@ -1105,15 +1044,6 @@ } if (ret) return ret; - -#if defined(DISPLAY_HPT366_TIMINGS) && defined(CONFIG_PROC_FS) - hpt_devs[n_hpt_devs++] = dev; - - if (!hpt366_proc) { - hpt366_proc = 1; - ide_pci_create_host_proc("hpt366", hpt366_get_info); - } -#endif /* DISPLAY_HPT366_TIMINGS && CONFIG_PROC_FS */ return dev->irq; } diff -Nru a/drivers/ide/pci/hpt366.h b/drivers/ide/pci/hpt366.h --- a/drivers/ide/pci/hpt366.h 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/hpt366.h 2004-10-23 23:29:01 +02:00 @@ -5,8 +5,6 @@ #include #include -#define DISPLAY_HPT366_TIMINGS - /* various tuning parameters */ #define HPT_RESET_STATE_ENGINE #undef HPT_DELAY_INTERRUPT diff -Nru a/drivers/ide/pci/pdc202xx_new.c b/drivers/ide/pci/pdc202xx_new.c --- a/drivers/ide/pci/pdc202xx_new.c 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/pdc202xx_new.c 2004-10-23 23:29:01 +02:00 @@ -41,61 +41,6 @@ #define PDC202_DEBUG_CABLE 0 -#if defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS) -#include -#include - -static u8 pdcnew_proc = 0; -#define PDC202_MAX_DEVS 5 -static struct pci_dev *pdc202_devs[PDC202_MAX_DEVS]; -static int n_pdc202_devs; - -static char * pdcnew_info(char *buf, struct pci_dev *dev) -{ - char *p = buf; - - p += sprintf(p, "\n "); - switch(dev->device) { - case PCI_DEVICE_ID_PROMISE_20277: - p += sprintf(p, "SBFastTrak 133 Lite"); break; - case PCI_DEVICE_ID_PROMISE_20276: - p += sprintf(p, "MBFastTrak 133 Lite"); break; - case PCI_DEVICE_ID_PROMISE_20275: - p += sprintf(p, "MBUltra133"); break; - case PCI_DEVICE_ID_PROMISE_20271: - p += sprintf(p, "FastTrak TX2000"); break; - case PCI_DEVICE_ID_PROMISE_20270: - p += sprintf(p, "FastTrak LP/TX2/TX4"); break; - case PCI_DEVICE_ID_PROMISE_20269: - p += sprintf(p, "Ultra133 TX2"); break; - case PCI_DEVICE_ID_PROMISE_20268: - p += sprintf(p, "Ultra100 TX2"); break; - default: - p += sprintf(p, "Ultra series"); break; - break; - } - p += sprintf(p, " Chipset.\n"); - return (char *)p; -} - -static int pdcnew_get_info (char *buffer, char **addr, off_t offset, int count) -{ - char *p = buffer; - int i, len; - - for (i = 0; i < n_pdc202_devs; i++) { - struct pci_dev *dev = pdc202_devs[i]; - p = pdcnew_info(buffer, dev); - } - /* p - buffer must be less than 4k! */ - len = (p - buffer) - offset; - *addr = buffer + offset; - - return len > count ? count : len; -} -#endif /* defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS) */ - - static u8 pdcnew_ratemask (ide_drive_t *drive) { u8 mode; @@ -416,15 +361,6 @@ #ifdef CONFIG_PPC_PMAC apple_kiwi_init(dev); #endif - -#if defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS) - pdc202_devs[n_pdc202_devs++] = dev; - - if (!pdcnew_proc) { - pdcnew_proc = 1; - ide_pci_create_host_proc("pdcnew", pdcnew_get_info); - } -#endif /* DISPLAY_PDC202XX_TIMINGS && CONFIG_PROC_FS */ return dev->irq; } diff -Nru a/drivers/ide/pci/pdc202xx_new.h b/drivers/ide/pci/pdc202xx_new.h --- a/drivers/ide/pci/pdc202xx_new.h 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/pdc202xx_new.h 2004-10-23 23:29:01 +02:00 @@ -43,8 +43,6 @@ set_2regs(0x13,(c)); \ } while(0) -#define DISPLAY_PDC202XX_TIMINGS - static void init_setup_pdcnew(struct pci_dev *, ide_pci_device_t *); static void init_setup_pdc20270(struct pci_dev *, ide_pci_device_t *); static void init_setup_pdc20276(struct pci_dev *dev, ide_pci_device_t *d); diff -Nru a/drivers/ide/pci/pdc202xx_old.c b/drivers/ide/pci/pdc202xx_old.c --- a/drivers/ide/pci/pdc202xx_old.c 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/pdc202xx_old.c 2004-10-23 23:29:01 +02:00 @@ -50,68 +50,14 @@ #define PDC202_DEBUG_CABLE 0 -#if defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS) -#include -#include - -static u8 pdc202xx_proc = 0; -#define PDC202_MAX_DEVS 5 -static struct pci_dev *pdc202_devs[PDC202_MAX_DEVS]; -static int n_pdc202_devs; - -static char * pdc202xx_info (char *buf, struct pci_dev *dev) -{ - char *p = buf; - +#if 0 unsigned long bibma = pci_resource_start(dev, 4); - u32 reg60h = 0, reg64h = 0, reg68h = 0, reg6ch = 0; - u16 reg50h = 0, pmask = (1<<10), smask = (1<<11); u8 hi = 0, lo = 0; - /* - * at that point bibma+0x2 et bibma+0xa are byte registers - * to investigate: - */ - u8 c0 = inb_p((u16)bibma + 0x02); - u8 c1 = inb_p((u16)bibma + 0x0a); - - u8 sc11 = inb_p((u16)bibma + 0x11); - u8 sc1a = inb_p((u16)bibma + 0x1a); - u8 sc1b = inb_p((u16)bibma + 0x1b); u8 sc1c = inb_p((u16)bibma + 0x1c); - u8 sc1d = inb_p((u16)bibma + 0x1d); u8 sc1e = inb_p((u16)bibma + 0x1e); u8 sc1f = inb_p((u16)bibma + 0x1f); - pci_read_config_word(dev, 0x50, ®50h); - pci_read_config_dword(dev, 0x60, ®60h); - pci_read_config_dword(dev, 0x64, ®64h); - pci_read_config_dword(dev, 0x68, ®68h); - pci_read_config_dword(dev, 0x6c, ®6ch); - - p += sprintf(p, "\n "); - switch(dev->device) { - case PCI_DEVICE_ID_PROMISE_20267: - p += sprintf(p, "Ultra100"); break; - case PCI_DEVICE_ID_PROMISE_20265: - p += sprintf(p, "Ultra100 on M/B"); break; - case PCI_DEVICE_ID_PROMISE_20263: - p += sprintf(p, "FastTrak 66"); break; - case PCI_DEVICE_ID_PROMISE_20262: - p += sprintf(p, "Ultra66"); break; - case PCI_DEVICE_ID_PROMISE_20246: - p += sprintf(p, "Ultra33"); - reg50h |= 0x0c00; - break; - default: - p += sprintf(p, "Ultra Series"); break; - } - p += sprintf(p, " Chipset.\n"); - - p += sprintf(p, "------------------------------- General Status " - "---------------------------------\n"); - p += sprintf(p, "Burst Mode : %sabled\n", - (sc1f & 0x01) ? "en" : "dis"); p += sprintf(p, "Host Mode : %s\n", (sc1f & 0x08) ? "Tri-Stated" : "Normal"); p += sprintf(p, "Bus Clocking : %s\n", @@ -126,70 +72,7 @@ SPLIT_BYTE(sc1e, hi, lo); p += sprintf(p, "Status Polling Period : %d\n", hi); p += sprintf(p, "Interrupt Check Status Polling Delay : %d\n", lo); - p += sprintf(p, "--------------- Primary Channel " - "---------------- Secondary Channel " - "-------------\n"); - p += sprintf(p, " %s %s\n", - (c0&0x80)?"disabled":"enabled ", - (c1&0x80)?"disabled":"enabled "); - p += sprintf(p, "66 Clocking %s %s\n", - (sc11&0x02)?"enabled ":"disabled", - (sc11&0x08)?"enabled ":"disabled"); - p += sprintf(p, " Mode %s Mode %s\n", - (sc1a & 0x01) ? "MASTER" : "PCI ", - (sc1b & 0x01) ? "MASTER" : "PCI "); - p += sprintf(p, " %s %s\n", - (sc1d & 0x08) ? "Error " : - ((sc1d & 0x05) == 0x05) ? "Not My INTR " : - (sc1d & 0x04) ? "Interrupting" : - (sc1d & 0x02) ? "FIFO Full " : - (sc1d & 0x01) ? "FIFO Empty " : "????????????", - (sc1d & 0x80) ? "Error " : - ((sc1d & 0x50) == 0x50) ? "Not My INTR " : - (sc1d & 0x40) ? "Interrupting" : - (sc1d & 0x20) ? "FIFO Full " : - (sc1d & 0x10) ? "FIFO Empty " : "????????????"); - p += sprintf(p, "--------------- drive0 --------- drive1 " - "-------- drive0 ---------- drive1 ------\n"); - p += sprintf(p, "DMA enabled: %s %s " - " %s %s\n", - (c0&0x20)?"yes":"no ", (c0&0x40)?"yes":"no ", - (c1&0x20)?"yes":"no ", (c1&0x40)?"yes":"no "); - p += sprintf(p, "DMA Mode: %s %s " - " %s %s\n", - pdc202xx_ultra_verbose(reg60h, (reg50h & pmask)), - pdc202xx_ultra_verbose(reg64h, (reg50h & pmask)), - pdc202xx_ultra_verbose(reg68h, (reg50h & smask)), - pdc202xx_ultra_verbose(reg6ch, (reg50h & smask))); - p += sprintf(p, "PIO Mode: %s %s " - " %s %s\n", - pdc202xx_pio_verbose(reg60h), - pdc202xx_pio_verbose(reg64h), - pdc202xx_pio_verbose(reg68h), - pdc202xx_pio_verbose(reg6ch)); -#if 0 - p += sprintf(p, "--------------- Can ATAPI DMA ---------------\n"); #endif - return (char *)p; -} - -static int pdc202xx_get_info (char *buffer, char **addr, off_t offset, int count) -{ - char *p = buffer; - int i, len; - - for (i = 0; i < n_pdc202_devs; i++) { - struct pci_dev *dev = pdc202_devs[i]; - p = pdc202xx_info(buffer, dev); - } - /* p - buffer must be less than 4k! */ - len = (p - buffer) - offset; - *addr = buffer + offset; - - return len > count ? count : len; -} -#endif /* defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS) */ - static u8 pdc202xx_ratemask (ide_drive_t *drive) { @@ -546,11 +429,13 @@ u8 sc1d = hwif->INB((high_16 + 0x001d)); if (hwif->channel) { + /* bit7: Error, bit6: Interrupting, bit5: FIFO Full, bit4: FIFO Empty */ if ((sc1d & 0x50) == 0x50) goto somebody_else; else if ((sc1d & 0x40) == 0x40) return (dma_stat & 4) == 4; } else { + /* bit3: Error, bit2: Interrupting, bit1: FIFO Full, bit0: FIFO Empty */ if ((sc1d & 0x05) == 0x05) goto somebody_else; else if ((sc1d & 0x04) == 0x04) @@ -667,15 +552,6 @@ printk(KERN_INFO "%s: ROM enabled at 0x%08lx\n", name, dev->resource[PCI_ROM_RESOURCE].start); } - -#if defined(DISPLAY_PDC202XX_TIMINGS) && defined(CONFIG_PROC_FS) - pdc202_devs[n_pdc202_devs++] = dev; - - if (!pdc202xx_proc) { - pdc202xx_proc = 1; - ide_pci_create_host_proc("pdc202xx", pdc202xx_get_info); - } -#endif /* DISPLAY_PDC202XX_TIMINGS && CONFIG_PROC_FS */ /* * software reset - this is required because the bios diff -Nru a/drivers/ide/pci/pdc202xx_old.h b/drivers/ide/pci/pdc202xx_old.h --- a/drivers/ide/pci/pdc202xx_old.h 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/pdc202xx_old.h 2004-10-23 23:29:01 +02:00 @@ -23,41 +23,6 @@ NULL }; -static inline u8 *pdc202xx_pio_verbose (u32 drive_pci) -{ - if ((drive_pci & 0x000ff000) == 0x000ff000) return("NOTSET"); - if ((drive_pci & 0x00000401) == 0x00000401) return("PIO 4"); - if ((drive_pci & 0x00000602) == 0x00000602) return("PIO 3"); - if ((drive_pci & 0x00000803) == 0x00000803) return("PIO 2"); - if ((drive_pci & 0x00000C05) == 0x00000C05) return("PIO 1"); - if ((drive_pci & 0x00001309) == 0x00001309) return("PIO 0"); - return("PIO ?"); -} - -static inline u8 *pdc202xx_dma_verbose (u32 drive_pci) -{ - if ((drive_pci & 0x00036000) == 0x00036000) return("MWDMA 2"); - if ((drive_pci & 0x00046000) == 0x00046000) return("MWDMA 1"); - if ((drive_pci & 0x00056000) == 0x00056000) return("MWDMA 0"); - if ((drive_pci & 0x00056000) == 0x00056000) return("SWDMA 2"); - if ((drive_pci & 0x00068000) == 0x00068000) return("SWDMA 1"); - if ((drive_pci & 0x000BC000) == 0x000BC000) return("SWDMA 0"); - return("PIO---"); -} - -static inline u8 *pdc202xx_ultra_verbose (u32 drive_pci, u16 slow_cable) -{ - if ((drive_pci & 0x000ff000) == 0x000ff000) - return("NOTSET"); - if ((drive_pci & 0x00012000) == 0x00012000) - return((slow_cable) ? "UDMA 2" : "UDMA 4"); - if ((drive_pci & 0x00024000) == 0x00024000) - return((slow_cable) ? "UDMA 1" : "UDMA 3"); - if ((drive_pci & 0x00036000) == 0x00036000) - return("UDMA 0"); - return(pdc202xx_dma_verbose(drive_pci)); -} - /* A Register */ #define SYNC_ERRDY_EN 0xC0 @@ -97,8 +62,6 @@ #define MC2 0x04 /* DMA"C" timing */ #define MC1 0x02 /* DMA"C" timing */ #define MC0 0x01 /* DMA"C" timing */ - -#define DISPLAY_PDC202XX_TIMINGS static void init_setup_pdc202ata4(struct pci_dev *dev, ide_pci_device_t *d); static void init_setup_pdc20265(struct pci_dev *, ide_pci_device_t *); diff -Nru a/drivers/ide/pci/piix.c b/drivers/ide/pci/piix.c --- a/drivers/ide/pci/piix.c 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/piix.c 2004-10-23 23:29:01 +02:00 @@ -106,165 +106,6 @@ #include "piix.h" static int no_piix_dma; -#if defined(DISPLAY_PIIX_TIMINGS) && defined(CONFIG_PROC_FS) -#include -#include - -static u8 piix_proc = 0; -#define PIIX_MAX_DEVS 5 -static struct pci_dev *piix_devs[PIIX_MAX_DEVS]; -static int n_piix_devs; - -/** - * piix_get_info - fill in /proc for PIIX ide - * @buffer: buffer to fill - * @addr: address of user start in buffer - * @offset: offset into 'file' - * @count: buffer count - * - * Walks the PIIX devices and outputs summary data on the tuning and - * anything else that will help with debugging - */ - -static int piix_get_info (char *buffer, char **addr, off_t offset, int count) -{ - char *p = buffer; - int i; - - for (i = 0; i < n_piix_devs; i++) { - struct pci_dev *dev = piix_devs[i]; - unsigned long bibma = pci_resource_start(dev, 4); - u16 reg40 = 0, psitre = 0, reg42 = 0, ssitre = 0; - u8 c0 = 0, c1 = 0, reg54 = 0, reg55 = 0; - u8 reg44 = 0, reg48 = 0, reg4a = 0, reg4b = 0; - - p += sprintf(p, "\nController: %d\n", i); - p += sprintf(p, "\n Intel "); - switch(dev->device) { - case PCI_DEVICE_ID_INTEL_82801EB_1: - p += sprintf(p, "PIIX4 SATA 150 "); - break; - case PCI_DEVICE_ID_INTEL_82801BA_8: - case PCI_DEVICE_ID_INTEL_82801BA_9: - case PCI_DEVICE_ID_INTEL_82801CA_10: - case PCI_DEVICE_ID_INTEL_82801CA_11: - case PCI_DEVICE_ID_INTEL_82801DB_10: - case PCI_DEVICE_ID_INTEL_82801DB_11: - case PCI_DEVICE_ID_INTEL_82801EB_11: - case PCI_DEVICE_ID_INTEL_82801E_11: - case PCI_DEVICE_ID_INTEL_ESB_2: - case PCI_DEVICE_ID_INTEL_ICH6_19: - p += sprintf(p, "PIIX4 Ultra 100 "); - break; - case PCI_DEVICE_ID_INTEL_82372FB_1: - case PCI_DEVICE_ID_INTEL_82801AA_1: - p += sprintf(p, "PIIX4 Ultra 66 "); - break; - case PCI_DEVICE_ID_INTEL_82451NX: - case PCI_DEVICE_ID_INTEL_82801AB_1: - case PCI_DEVICE_ID_INTEL_82443MX_1: - case PCI_DEVICE_ID_INTEL_82371AB: - p += sprintf(p, "PIIX4 Ultra 33 "); - break; - case PCI_DEVICE_ID_INTEL_82371SB_1: - p += sprintf(p, "PIIX3 "); - break; - case PCI_DEVICE_ID_INTEL_82371MX: - p += sprintf(p, "MPIIX "); - break; - case PCI_DEVICE_ID_INTEL_82371FB_1: - case PCI_DEVICE_ID_INTEL_82371FB_0: - default: - p += sprintf(p, "PIIX "); - break; - } - p += sprintf(p, "Chipset.\n"); - - if (dev->device == PCI_DEVICE_ID_INTEL_82371MX) - continue; - - pci_read_config_word(dev, 0x40, ®40); - pci_read_config_word(dev, 0x42, ®42); - pci_read_config_byte(dev, 0x44, ®44); - pci_read_config_byte(dev, 0x48, ®48); - pci_read_config_byte(dev, 0x4a, ®4a); - pci_read_config_byte(dev, 0x4b, ®4b); - pci_read_config_byte(dev, 0x54, ®54); - pci_read_config_byte(dev, 0x55, ®55); - - psitre = (reg40 & 0x4000) ? 1 : 0; - ssitre = (reg42 & 0x4000) ? 1 : 0; - - /* - * at that point bibma+0x2 et bibma+0xa are byte registers - * to investigate: - */ - c0 = inb(bibma + 0x02); - c1 = inb(bibma + 0x0a); - - p += sprintf(p, "--------------- Primary Channel " - "---------------- Secondary Channel " - "-------------\n"); - p += sprintf(p, " %sabled " - " %sabled\n", - (c0&0x80) ? "dis" : " en", - (c1&0x80) ? "dis" : " en"); - p += sprintf(p, "--------------- drive0 --------- drive1 " - "-------- drive0 ---------- drive1 ------\n"); - p += sprintf(p, "DMA enabled: %s %s " - " %s %s\n", - (c0&0x20) ? "yes" : "no ", - (c0&0x40) ? "yes" : "no ", - (c1&0x20) ? "yes" : "no ", - (c1&0x40) ? "yes" : "no " ); - p += sprintf(p, "UDMA enabled: %s %s " - " %s %s\n", - (reg48&0x01) ? "yes" : "no ", - (reg48&0x02) ? "yes" : "no ", - (reg48&0x04) ? "yes" : "no ", - (reg48&0x08) ? "yes" : "no " ); - p += sprintf(p, "UDMA enabled: %s %s " - " %s %s\n", - ((reg54&0x11) && - (reg55&0x10) && (reg4a&0x01)) ? "5" : - ((reg54&0x11) && (reg4a&0x02)) ? "4" : - ((reg54&0x11) && (reg4a&0x01)) ? "3" : - (reg4a&0x02) ? "2" : - (reg4a&0x01) ? "1" : - (reg4a&0x00) ? "0" : "X", - ((reg54&0x22) && - (reg55&0x20) && (reg4a&0x10)) ? "5" : - ((reg54&0x22) && (reg4a&0x20)) ? "4" : - ((reg54&0x22) && (reg4a&0x10)) ? "3" : - (reg4a&0x20) ? "2" : - (reg4a&0x10) ? "1" : - (reg4a&0x00) ? "0" : "X", - ((reg54&0x44) && - (reg55&0x40) && (reg4b&0x03)) ? "5" : - ((reg54&0x44) && (reg4b&0x02)) ? "4" : - ((reg54&0x44) && (reg4b&0x01)) ? "3" : - (reg4b&0x02) ? "2" : - (reg4b&0x01) ? "1" : - (reg4b&0x00) ? "0" : "X", - ((reg54&0x88) && - (reg55&0x80) && (reg4b&0x30)) ? "5" : - ((reg54&0x88) && (reg4b&0x20)) ? "4" : - ((reg54&0x88) && (reg4b&0x10)) ? "3" : - (reg4b&0x20) ? "2" : - (reg4b&0x10) ? "1" : - (reg4b&0x00) ? "0" : "X"); - - p += sprintf(p, "UDMA\n"); - p += sprintf(p, "DMA\n"); - p += sprintf(p, "PIO\n"); - - /* - * FIXME.... Add configuration junk data....blah blah...... - */ - } - return p-buffer; /* => must be less than 4k! */ -} -#endif /* defined(DISPLAY_PIIX_TIMINGS) && defined(CONFIG_PROC_FS) */ /** * piix_ratemask - compute rate mask for PIIX IDE @@ -627,14 +468,6 @@ break; } -#if defined(DISPLAY_PIIX_TIMINGS) && defined(CONFIG_PROC_FS) - piix_devs[n_piix_devs++] = dev; - - if (!piix_proc) { - piix_proc = 1; - ide_pci_create_host_proc("piix", piix_get_info); - } -#endif /* DISPLAY_PIIX_TIMINGS && CONFIG_PROC_FS */ return 0; } diff -Nru a/drivers/ide/pci/piix.h b/drivers/ide/pci/piix.h --- a/drivers/ide/pci/piix.h 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/piix.h 2004-10-23 23:29:01 +02:00 @@ -5,10 +5,6 @@ #include #include -#define PIIX_DEBUG_DRIVE_INFO 0 - -#define DISPLAY_PIIX_TIMINGS - static void init_setup_piix(struct pci_dev *, ide_pci_device_t *); static unsigned int __devinit init_chipset_piix(struct pci_dev *, const char *); static void init_hwif_piix(ide_hwif_t *); diff -Nru a/drivers/ide/pci/sc1200.c b/drivers/ide/pci/sc1200.c --- a/drivers/ide/pci/sc1200.c 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/sc1200.c 2004-10-23 23:29:01 +02:00 @@ -67,55 +67,6 @@ return pci_clock; } -#define DISPLAY_SC1200_TIMINGS - -#if defined(DISPLAY_SC1200_TIMINGS) && defined(CONFIG_PROC_FS) -#include -#include - -static int sc1200_get_info(char *, char **, off_t, int); -extern int (*sc1200_display_info)(char *, char **, off_t, int); /* ide-proc.c */ -extern char *ide_media_verbose(ide_drive_t *); -static u8 sc1200_proc = 0; - -static struct pci_dev *bmide_dev; - -static int sc1200_get_info (char *buffer, char **addr, off_t offset, int count) -{ - char *p = buffer; - unsigned long bibma = pci_resource_start(bmide_dev, 4); - int len; - u8 c0 = 0, c1 = 0; - - /* - * at that point bibma+0x2 et bibma+0xa are byte registers - * to investigate: - */ - - c0 = inb_p(bibma + 0x02); - c1 = inb_p(bibma + 0x0a); - - p += sprintf(p, "\n National SCx200 Chipset.\n"); - p += sprintf(p, "--------------- Primary Channel ---------------- Secondary Channel -------------\n"); - p += sprintf(p, " %sabled %sabled\n", - (c0&0x80) ? "dis" : " en", - (c1&0x80) ? "dis" : " en"); - p += sprintf(p, "--------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------\n"); - p += sprintf(p, "DMA enabled: %s %s %s %s\n", - (c0&0x20) ? "yes" : "no ", (c0&0x40) ? "yes" : "no ", - (c1&0x20) ? "yes" : "no ", (c1&0x40) ? "yes" : "no " ); - - p += sprintf(p, "UDMA\n"); - p += sprintf(p, "DMA\n"); - p += sprintf(p, "PIO\n"); - - len = (p - buffer) - offset; - *addr = buffer + offset; - - return len > count ? count : len; -} -#endif /* DISPLAY_SC1200_TIMINGS && CONFIG_PROC_FS */ - extern char *ide_xfer_verbose (byte xfer_rate); /* @@ -505,21 +456,6 @@ } /* - * Initialize the sc1200 bridge for reliable IDE DMA operation. - */ -static unsigned int __init init_chipset_sc1200 (struct pci_dev *dev, const char *name) -{ -#if defined(DISPLAY_SC1200_TIMINGS) && defined(CONFIG_PROC_FS) - if (!bmide_dev) { - sc1200_proc = 1; - bmide_dev = dev; - ide_pci_create_host_proc("sc1200", sc1200_get_info); - } -#endif /* DISPLAY_SC1200_TIMINGS && CONFIG_PROC_FS */ - return 0; -} - -/* * This gets invoked by the IDE driver once for each channel, * and performs channel-specific pre-initialization before drive probing. */ @@ -545,7 +481,6 @@ static ide_pci_device_t sc1200_chipset __devinitdata = { .name = "SC1200", - .init_chipset = init_chipset_sc1200, .init_hwif = init_hwif_sc1200, .channels = 2, .autodma = AUTODMA, diff -Nru a/drivers/ide/pci/serverworks.c b/drivers/ide/pci/serverworks.c --- a/drivers/ide/pci/serverworks.c 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/serverworks.c 2004-10-23 23:29:01 +02:00 @@ -44,164 +44,6 @@ static u8 svwks_revision = 0; static struct pci_dev *isa_dev; -#if defined(DISPLAY_SVWKS_TIMINGS) && defined(CONFIG_PROC_FS) -#include -#include - -static u8 svwks_proc = 0; -#define SVWKS_MAX_DEVS 2 -static struct pci_dev *svwks_devs[SVWKS_MAX_DEVS]; -static int n_svwks_devs; - -static int svwks_get_info (char *buffer, char **addr, off_t offset, int count) -{ - char *p = buffer; - int i, len; - - p += sprintf(p, "\n " - "ServerWorks OSB4/CSB5/CSB6\n"); - - for (i = 0; i < n_svwks_devs; i++) { - struct pci_dev *dev = svwks_devs[i]; - unsigned long bibma = pci_resource_start(dev, 4); - u32 reg40, reg44; - u16 reg48, reg56; - u8 reg54, c0=0, c1=0; - - pci_read_config_dword(dev, 0x40, ®40); - pci_read_config_dword(dev, 0x44, ®44); - pci_read_config_word(dev, 0x48, ®48); - pci_read_config_byte(dev, 0x54, ®54); - pci_read_config_word(dev, 0x56, ®56); - - /* - * at that point bibma+0x2 et bibma+0xa are byte registers - * to investigate: - */ - c0 = inb_p(bibma + 0x02); - c1 = inb_p(bibma + 0x0a); - - p += sprintf(p, "\n ServerWorks "); - switch(dev->device) { - case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2: - case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE: - p += sprintf(p, "CSB6 "); - break; - case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE: - p += sprintf(p, "CSB5 "); - break; - case PCI_DEVICE_ID_SERVERWORKS_OSB4IDE: - p += sprintf(p, "OSB4 "); - break; - default: - p += sprintf(p, "%04x ", dev->device); - break; - } - p += sprintf(p, "Chipset (rev %02x)\n", svwks_revision); - - p += sprintf(p, "------------------------------- " - "General Status " - "---------------------------------\n"); - p += sprintf(p, "--------------- Primary Channel " - "---------------- Secondary Channel " - "-------------\n"); - p += sprintf(p, " %sabled" - " %sabled\n", - (c0&0x80) ? "dis" : " en", - (c1&0x80) ? "dis" : " en"); - p += sprintf(p, "--------------- drive0 --------- drive1 " - "-------- drive0 ---------- drive1 ------\n"); - p += sprintf(p, "DMA enabled: %s %s" - " %s %s\n", - (c0&0x20) ? "yes" : "no ", - (c0&0x40) ? "yes" : "no ", - (c1&0x20) ? "yes" : "no ", - (c1&0x40) ? "yes" : "no " ); - p += sprintf(p, "UDMA enabled: %s %s" - " %s %s\n", - (reg54 & 0x01) ? "yes" : "no ", - (reg54 & 0x02) ? "yes" : "no ", - (reg54 & 0x04) ? "yes" : "no ", - (reg54 & 0x08) ? "yes" : "no " ); - p += sprintf(p, "UDMA enabled: %s %s" - " %s %s\n", - ((reg56&0x0005)==0x0005)?"5": - ((reg56&0x0004)==0x0004)?"4": - ((reg56&0x0003)==0x0003)?"3": - ((reg56&0x0002)==0x0002)?"2": - ((reg56&0x0001)==0x0001)?"1": - ((reg56&0x000F))?"?":"0", - ((reg56&0x0050)==0x0050)?"5": - ((reg56&0x0040)==0x0040)?"4": - ((reg56&0x0030)==0x0030)?"3": - ((reg56&0x0020)==0x0020)?"2": - ((reg56&0x0010)==0x0010)?"1": - ((reg56&0x00F0))?"?":"0", - ((reg56&0x0500)==0x0500)?"5": - ((reg56&0x0400)==0x0400)?"4": - ((reg56&0x0300)==0x0300)?"3": - ((reg56&0x0200)==0x0200)?"2": - ((reg56&0x0100)==0x0100)?"1": - ((reg56&0x0F00))?"?":"0", - ((reg56&0x5000)==0x5000)?"5": - ((reg56&0x4000)==0x4000)?"4": - ((reg56&0x3000)==0x3000)?"3": - ((reg56&0x2000)==0x2000)?"2": - ((reg56&0x1000)==0x1000)?"1": - ((reg56&0xF000))?"?":"0"); - p += sprintf(p, "DMA enabled: %s %s" - " %s %s\n", - ((reg44&0x00002000)==0x00002000)?"2": - ((reg44&0x00002100)==0x00002100)?"1": - ((reg44&0x00007700)==0x00007700)?"0": - ((reg44&0x0000FF00)==0x0000FF00)?"X":"?", - ((reg44&0x00000020)==0x00000020)?"2": - ((reg44&0x00000021)==0x00000021)?"1": - ((reg44&0x00000077)==0x00000077)?"0": - ((reg44&0x000000FF)==0x000000FF)?"X":"?", - ((reg44&0x20000000)==0x20000000)?"2": - ((reg44&0x21000000)==0x21000000)?"1": - ((reg44&0x77000000)==0x77000000)?"0": - ((reg44&0xFF000000)==0xFF000000)?"X":"?", - ((reg44&0x00200000)==0x00200000)?"2": - ((reg44&0x00210000)==0x00210000)?"1": - ((reg44&0x00770000)==0x00770000)?"0": - ((reg44&0x00FF0000)==0x00FF0000)?"X":"?"); - - p += sprintf(p, "PIO enabled: %s %s" - " %s %s\n", - ((reg40&0x00002000)==0x00002000)?"4": - ((reg40&0x00002200)==0x00002200)?"3": - ((reg40&0x00003400)==0x00003400)?"2": - ((reg40&0x00004700)==0x00004700)?"1": - ((reg40&0x00005D00)==0x00005D00)?"0":"?", - ((reg40&0x00000020)==0x00000020)?"4": - ((reg40&0x00000022)==0x00000022)?"3": - ((reg40&0x00000034)==0x00000034)?"2": - ((reg40&0x00000047)==0x00000047)?"1": - ((reg40&0x0000005D)==0x0000005D)?"0":"?", - ((reg40&0x20000000)==0x20000000)?"4": - ((reg40&0x22000000)==0x22000000)?"3": - ((reg40&0x34000000)==0x34000000)?"2": - ((reg40&0x47000000)==0x47000000)?"1": - ((reg40&0x5D000000)==0x5D000000)?"0":"?", - ((reg40&0x00200000)==0x00200000)?"4": - ((reg40&0x00220000)==0x00220000)?"3": - ((reg40&0x00340000)==0x00340000)?"2": - ((reg40&0x00470000)==0x00470000)?"1": - ((reg40&0x005D0000)==0x005D0000)?"0":"?"); - - } - p += sprintf(p, "\n"); - - /* p - buffer must be less than 4k! */ - len = (p - buffer) - offset; - *addr = buffer + offset; - - return len > count ? count : len; -} -#endif /* defined(DISPLAY_SVWKS_TIMINGS) && defined(CONFIG_PROC_FS) */ - static int check_in_drive_lists (ide_drive_t *drive, const char **list) { while (*list) @@ -616,16 +458,6 @@ btr |= (svwks_revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2; pci_write_config_byte(dev, 0x5A, btr); } - - -#if defined(DISPLAY_SVWKS_TIMINGS) && defined(CONFIG_PROC_FS) - svwks_devs[n_svwks_devs++] = dev; - - if (!svwks_proc) { - svwks_proc = 1; - ide_pci_create_host_proc("svwks", svwks_get_info); - } -#endif /* DISPLAY_SVWKS_TIMINGS && CONFIG_PROC_FS */ return (dev->irq) ? dev->irq : 0; } diff -Nru a/drivers/ide/pci/serverworks.h b/drivers/ide/pci/serverworks.h --- a/drivers/ide/pci/serverworks.h 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/serverworks.h 2004-10-23 23:29:01 +02:00 @@ -21,8 +21,6 @@ NULL }; -#define DISPLAY_SVWKS_TIMINGS 1 - static void init_setup_svwks(struct pci_dev *, ide_pci_device_t *); static void init_setup_csb6(struct pci_dev *, ide_pci_device_t *); static unsigned int init_chipset_svwks(struct pci_dev *, const char *); diff -Nru a/drivers/ide/pci/slc90e66.c b/drivers/ide/pci/slc90e66.c --- a/drivers/ide/pci/slc90e66.c 2004-10-23 23:29:01 +02:00 +++ b/drivers/ide/pci/slc90e66.c 2004-10-23 23:29:01 +02:00 @@ -21,103 +21,6 @@ #include -#define DISPLAY_SLC90E66_TIMINGS - -#if defined(DISPLAY_SLC90E66_TIMINGS) && defined(CONFIG_PROC_FS) -#include -#include - -static u8 slc90e66_proc = 0; -static struct pci_dev *bmide_dev; - -static int slc90e66_get_info (char *buffer, char **addr, off_t offset, int count) -{ - char *p = buffer; - int len; - unsigned long bibma = pci_resource_start(bmide_dev, 4); - u16 reg40 = 0, psitre = 0, reg42 = 0, ssitre = 0; - u8 c0 = 0, c1 = 0; - u8 reg44 = 0, reg47 = 0, reg48 = 0, reg4a = 0, reg4b = 0; - - pci_read_config_word(bmide_dev, 0x40, ®40); - pci_read_config_word(bmide_dev, 0x42, ®42); - pci_read_config_byte(bmide_dev, 0x44, ®44); - pci_read_config_byte(bmide_dev, 0x47, ®47); - pci_read_config_byte(bmide_dev, 0x48, ®48); - pci_read_config_byte(bmide_dev, 0x4a, ®4a); - pci_read_config_byte(bmide_dev, 0x4b, ®4b); - - psitre = (reg40 & 0x4000) ? 1 : 0; - ssitre = (reg42 & 0x4000) ? 1 : 0; - - /* - * at that point bibma+0x2 et bibma+0xa are byte registers - * to investigate: - */ - c0 = inb_p(bibma + 0x02); - c1 = inb_p(bibma + 0x0a); - - p += sprintf(p, " SLC90E66 Chipset.\n"); - p += sprintf(p, "--------------- Primary Channel " - "---------------- Secondary Channel " - "-------------\n"); - p += sprintf(p, " %sabled " - " %sabled\n", - (c0&0x80) ? "dis" : " en", - (c1&0x80) ? "dis" : " en"); - p += sprintf(p, "--------------- drive0 --------- drive1 " - "-------- drive0 ---------- drive1 ------\n"); - p += sprintf(p, "DMA enabled: %s %s " - " %s %s\n", - (c0&0x20) ? "yes" : "no ", - (c0&0x40) ? "yes" : "no ", - (c1&0x20) ? "yes" : "no ", - (c1&0x40) ? "yes" : "no " ); - p += sprintf(p, "UDMA enabled: %s %s " - " %s %s\n", - (reg48&0x01) ? "yes" : "no ", - (reg48&0x02) ? "yes" : "no ", - (reg48&0x04) ? "yes" : "no ", - (reg48&0x08) ? "yes" : "no " ); - p += sprintf(p, "UDMA enabled: %s %s " - " %s %s\n", - ((reg4a&0x04)==0x04) ? "4" : - ((reg4a&0x03)==0x03) ? "3" : - (reg4a&0x02) ? "2" : - (reg4a&0x01) ? "1" : - (reg4a&0x00) ? "0" : "X", - ((reg4a&0x40)==0x40) ? "4" : - ((reg4a&0x30)==0x30) ? "3" : - (reg4a&0x20) ? "2" : - (reg4a&0x10) ? "1" : - (reg4a&0x00) ? "0" : "X", - ((reg4b&0x04)==0x04) ? "4" : - ((reg4b&0x03)==0x03) ? "3" : - (reg4b&0x02) ? "2" : - (reg4b&0x01) ? "1" : - (reg4b&0x00) ? "0" : "X", - ((reg4b&0x40)==0x40) ? "4" : - ((reg4b&0x30)==0x30) ? "3" : - (reg4b&0x20) ? "2" : - (reg4b&0x10) ? "1" : - (reg4b&0x00) ? "0" : "X"); - - p += sprintf(p, "UDMA\n"); - p += sprintf(p, "DMA\n"); - p += sprintf(p, "PIO\n"); - -/* - * FIXME.... Add configuration junk data....blah blah...... - */ - - /* p - buffer must be less than 4k! */ - len = (p - buffer) - offset; - *addr = buffer + offset; - - return len > count ? count : len; -} -#endif /* defined(DISPLAY_SLC90E66_TIMINGS) && defined(CONFIG_PROC_FS) */ - static u8 slc90e66_ratemask (ide_drive_t *drive) { u8 mode = 2; @@ -236,6 +139,7 @@ if (speed >= XFER_UDMA_0) { if (!(reg48 & u_flag)) pci_write_config_word(dev, 0x48, reg48|u_flag); + /* FIXME: (reg4a & a_speed) ? */ if ((reg4a & u_speed) != u_speed) { pci_write_config_word(dev, 0x4a, reg4a & ~a_speed); pci_read_config_word(dev, 0x4a, ®4a); @@ -313,18 +217,6 @@ } #endif /* CONFIG_BLK_DEV_IDEDMA */ -static unsigned int __init init_chipset_slc90e66 (struct pci_dev *dev, const char *name) -{ -#if defined(DISPLAY_SLC90E66_TIMINGS) && defined(CONFIG_PROC_FS) - if (!slc90e66_proc) { - slc90e66_proc = 1; - bmide_dev = dev; - ide_pci_create_host_proc("slc90e66", slc90e66_get_info); - } -#endif /* DISPLAY_SLC90E66_TIMINGS && CONFIG_PROC_FS */ - return 0; -} - static void __init init_hwif_slc90e66 (ide_hwif_t *hwif) { u8 reg47 = 0; @@ -366,7 +258,6 @@ static ide_pci_device_t slc90e66_chipset __devinitdata = { .name = "SLC90E66", - .init_chipset = init_chipset_slc90e66, .init_hwif = init_hwif_slc90e66, .channels = 2, .autodma = AUTODMA, - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/