Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
From:   Chunfeng Yun <chunfeng.yun@mediatek.com>
To:     Rob Herring <robh+dt@kernel.org>,
        Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
        Heikki Krogerus <heikki.krogerus@linux.intel.com>
CC:     Mark Rutland <mark.rutland@arm.com>,
        Chunfeng Yun <chunfeng.yun@mediatek.com>,
        Matthias Brugger <matthias.bgg@gmail.com>,
        Adam Thomson <Adam.Thomson.Opensource@diasemi.com>,
        Li Jun <jun.li@nxp.com>,
        Badhri Jagan Sridharan <badhri@google.com>,
        Hans de Goede <hdegoede@redhat.com>,
        Andy Shevchenko <andy.shevchenko@gmail.com>,
        Min Guo <min.guo@mediatek.com>, <devicetree@vger.kernel.org>,
        <linux-kernel@vger.kernel.org>, <linux-usb@vger.kernel.org>,
        <linux-arm-kernel@lists.infradead.org>,
        <linux-mediatek@lists.infradead.org>,
        Biju Das <biju.das@bp.renesas.com>,
        Linus Walleij <linus.walleij@linaro.org>,
        Yu Chen <chenyu56@huawei.com>
Subject: [PATCH v6 03/10] dt-bindings: usb: add binding for Type-B GPIO connector driver
Date:   Wed, 29 May 2019 15:43:41 +0800
Message-ID: <1559115828-19146-4-git-send-email-chunfeng.yun@mediatek.com>
In-Reply-To: <1559115828-19146-1-git-send-email-chunfeng.yun@mediatek.com>
References: <1559115828-19146-1-git-send-email-chunfeng.yun@mediatek.com>
MIME-Version: 1.0
Content-Type: text/plain
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

It's used to support dual role switch via GPIO when use Type-B
receptacle, typically the USB ID pin is connected to an input
GPIO pin

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v6 changes:
 1. remove status and port nodes in example
 2. make vbus-supply as optional property

v5 changes:
 1. treat type-B connector as child device of USB controller's, but not
    as a separate virtual device, suggested by Rob
 2. put connector's port node under connector node, suggested by Rob

v4 no changes

v3 changes:
 1. treat type-B connector as a virtual device, but not child device of
    USB controller's

v2 changes:
  1. new patch to make binding clear suggested by Hans
---
 .../bindings/usb/typeb-conn-gpio.txt          | 30 +++++++++++++++++++
 1 file changed, 30 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt

diff --git a/Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt b/Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt
new file mode 100644
index 000000000000..5be443a16c6b
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/typeb-conn-gpio.txt
@@ -0,0 +1,30 @@
+USB Type-B GPIO Connector
+
+This is typically used to switch dual role mode from the USB ID pin connected
+to an input GPIO pin.
+
+Required properties:
+- compatible : should include "linux,typeb-conn-gpio" and "usb-b-connector".
+- id-gpios, vbus-gpios : input gpios, either one of them must be present,
+	and both can be present as well.
+	see connector/usb-connector.txt
+
+Optional properties:
+- vbus-supply : can be present if needed when supports dual role mode.
+	see connector/usb-connector.txt
+
+- Sub-nodes:
+	- port : can be present.
+		see graph.txt
+
+Example:
+
+&mtu3 {
+	connector {
+		compatible = "linux,typeb-conn-gpio", "usb-b-connector";
+		label = "micro-USB";
+		type = "micro";
+		id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
+		vbus-supply = <&usb_p0_vbus>;
+	};
+};
-- 
2.21.0