Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1030183AbVKVVeK (ORCPT ); Tue, 22 Nov 2005 16:34:10 -0500 Received: (majordomo@vger.kernel.org) by vger.kernel.org id S1030182AbVKVVeK (ORCPT ); Tue, 22 Nov 2005 16:34:10 -0500 Received: from bernhard.xss.co.at ([193.80.108.69]:42919 "EHLO bernhard.xss.co.at") by vger.kernel.org with ESMTP id S1030180AbVKVVeG (ORCPT ); Tue, 22 Nov 2005 16:34:06 -0500 Message-ID: <43838ECC.5060204@xss.co.at> Date: Tue, 22 Nov 2005 22:34:04 +0100 From: Andreas Haumer Organization: xS+S User-Agent: Mozilla Thunderbird 1.0.7 (X11/20050923) X-Accept-Language: de-DE, de, en-us, en MIME-Version: 1.0 To: linux-scsi@vger.kernel.org CC: linux-kernel@vger.kernel.org Subject: [2.4.31 + aic79xx] SCSI error: Infinite interrupt loop, INTSTAT = 0 X-Enigmail-Version: 0.92.1.0 Content-Type: text/plain; charset=ISO-8859-15 Content-Transfer-Encoding: 7bit Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 13679 Lines: 225 -----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi! I'm in the process of setting up a new fileserver and have some troubles with an Adaptec ASC-29320ALP U320 SCSI card and an external Infortrend EonStor RAID! This is a Tyan TA26 barebone system (dual opteron CPU, 4GB RAM) with two on-board AIC-7902B SCSI controllers (Tyan Thunder K8SD Pro motherboard) for internal system disks (SW-RAID1) and two additional Adaptec 29320ALP U320 cards for externally connected RAID (Infortrend EonStor A16U-G2421 RAID subsystem) and backup hardware. I'm running linux-2.4.31 in 32 bit mode. root@setup:~ {521} $ lspci 00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07) 00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05) 00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03) 00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02) 00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05) 00:0a.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) 00:0a.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) 00:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) 00:0b.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:03.0 SCSI storage controller: Adaptec ASC-29320ALP U320 (rev 10) 01:04.0 SCSI storage controller: Adaptec ASC-29320ALP U320 (rev 10) 02:06.0 SCSI storage controller: Adaptec AIC-7902B U320 (rev 10) 02:06.1 SCSI storage controller: Adaptec AIC-7902B U320 (rev 10) 02:09.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03) 02:09.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03) 03:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b) 03:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b) 03:05.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 03:06.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) 03:08.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 10) The SCSI devices are connected as follows: root@setup:~ {520} $ cat /proc/scsi/scsi Attached devices: Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: IFT Model: A16U-G2421 Rev: 342A Type: Direct-Access ANSI SCSI revision: 03 Host: scsi1 Channel: 00 Id: 00 Lun: 01 Vendor: IFT Model: A16U-G2421 Rev: 342A Type: Direct-Access ANSI SCSI revision: 03 Host: scsi2 Channel: 00 Id: 00 Lun: 00 Vendor: MAXTOR Model: ATLAS10K5_73SCA Rev: JNZH Type: Direct-Access ANSI SCSI revision: 03 Host: scsi3 Channel: 00 Id: 05 Lun: 00 Vendor: MAXTOR Model: ATLAS10K5_73SCA Rev: JNZH Type: Direct-Access ANSI SCSI revision: 03 SCSI driver boot messages: [...] Nov 22 19:53:52 setup kernel: SCSI subsystem driver Revision: 1.00 Nov 22 19:53:52 setup kernel: scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.10 Nov 22 19:53:52 setup kernel: Nov 22 19:53:52 setup kernel: aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs Nov 22 19:53:52 setup kernel: Nov 22 19:53:52 setup kernel: scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.10 Nov 22 19:53:52 setup kernel: Nov 22 19:53:52 setup kernel: aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs Nov 22 19:53:52 setup kernel: Nov 22 19:53:52 setup kernel: scsi2 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.10 Nov 22 19:53:52 setup kernel: Nov 22 19:53:52 setup kernel: aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs Nov 22 19:53:52 setup kernel: Nov 22 19:53:52 setup kernel: scsi3 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.10 Nov 22 19:53:52 setup kernel: Nov 22 19:53:52 setup kernel: aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs Nov 22 19:53:52 setup kernel: Nov 22 19:53:52 setup kernel: blk: queue f7ace618, I/O limit 4095Mb (mask 0xffffffff) Nov 22 19:53:52 setup kernel: (scsi2:A:0): 320.000MB/s transfers (160.000MHz DT|IU|RTI|QAS, 16bit) Nov 22 19:53:52 setup kernel: (scsi1:A:0): 320.000MB/s transfers (160.000MHz DT|IU|QAS, 16bit) Nov 22 19:53:52 setup kernel: (scsi3:A:5): 320.000MB/s transfers (160.000MHz DT|IU|RTI|QAS, 16bit) Nov 22 19:53:52 setup kernel: Vendor: IFT Model: A16U-G2421 Rev: 342A Nov 22 19:53:52 setup kernel: Type: Direct-Access ANSI SCSI revision: 03 Nov 22 19:53:52 setup kernel: blk: queue f7ace418, I/O limit 4095Mb (mask 0xffffffff) Nov 22 19:53:52 setup kernel: Vendor: IFT Model: A16U-G2421 Rev: 342A Nov 22 19:53:52 setup kernel: Type: Direct-Access ANSI SCSI revision: 03 Nov 22 19:53:52 setup kernel: blk: queue f7ace018, I/O limit 4095Mb (mask 0xffffffff) Nov 22 19:53:52 setup kernel: scsi1:A:0:0: Tagged Queuing enabled. Depth 32 Nov 22 19:53:52 setup kernel: scsi1:A:0:1: Tagged Queuing enabled. Depth 32 Nov 22 19:53:52 setup kernel: Vendor: MAXTOR Model: ATLAS10K5_73SCA Rev: JNZH Nov 22 19:53:52 setup kernel: Type: Direct-Access ANSI SCSI revision: 03 Nov 22 19:53:52 setup kernel: blk: queue f7261c18, I/O limit 4095Mb (mask 0xffffffff) Nov 22 19:53:52 setup kernel: scsi2:A:0:0: Tagged Queuing enabled. Depth 32 Nov 22 19:53:52 setup kernel: Vendor: MAXTOR Model: ATLAS10K5_73SCA Rev: JNZH Nov 22 19:53:52 setup kernel: Type: Direct-Access ANSI SCSI revision: 03 Nov 22 19:53:52 setup kernel: blk: queue f7261a18, I/O limit 4095Mb (mask 0xffffffff) Nov 22 19:53:52 setup kernel: scsi3:A:5:0: Tagged Queuing enabled. Depth 32 Nov 22 19:53:52 setup kernel: Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 Nov 22 19:53:52 setup kernel: Attached scsi disk sdb at scsi1, channel 0, id 0, lun 1 Nov 22 19:53:52 setup kernel: Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0 Nov 22 19:53:52 setup kernel: Attached scsi disk sdd at scsi3, channel 0, id 5, lun 0 [...] Both Maxtor discs are used in a SW-RAID1 for the system volume group and they work fine for a few days now. Today I tried to integrate the external EonStor RAID and first it seemd to work fine, too. The system did find the devices and I could create a new volume group with several logical volumes out of them. But as soon as I try to create a filesystem on the new logical volumes or do some other work with the devices, the SCSI driver goes berserk: [...] Nov 22 19:56:14 setup kernel: scsi1:0:0:0: Attempting to abort cmd f71dec00: 0x2a 0x0 0x1 0x71 0x3 0x0 0x0 0x0 0x8 0x0 Nov 22 19:56:14 setup kernel: Infinite interrupt loop, INTSTAT = 0scsi1: At time of recovery, card was not paused Nov 22 19:56:14 setup kernel: >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<< Nov 22 19:56:14 setup kernel: scsi1: Dumping Card State at program address 0x26 Mode 0x22 Nov 22 19:56:14 setup kernel: Card was paused Nov 22 19:56:14 setup kernel: HS_MAILBOX[0x0] INTCTL[0x80] SEQINTSTAT[0x0] SAVED_MODE[0x11] Nov 22 19:56:14 setup kernel: DFFSTAT[0x33] SCSISIGI[0x25] SCSIPHASE[0x0] SCSIBUS[0x0] Nov 22 19:56:14 setup kernel: LASTPHASE[0x1] SCSISEQ0[0x40] SCSISEQ1[0x12] SEQCTL0[0x0] Nov 22 19:56:14 setup kernel: SEQINTCTL[0x0] SEQ_FLAGS[0x0] SEQ_FLAGS2[0x0] SSTAT0[0x10] Nov 22 19:56:14 setup kernel: SSTAT1[0x0] SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0xc0] Nov 22 19:56:14 setup kernel: SIMODE1[0xac] LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x80] Nov 22 19:56:14 setup kernel: LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x40] Nov 22 19:56:14 setup kernel: Nov 22 19:56:14 setup kernel: SCB Count = 32 CMDS_PENDING = 32 LASTSCB 0x10 CURRSCB 0x7 NEXTSCB 0xff80 Nov 22 19:56:14 setup kernel: qinstart = 268 qinfifonext = 268 Nov 22 19:56:14 setup kernel: QINFIFO: Nov 22 19:56:14 setup kernel: WAITING_TID_QUEUES: Nov 22 19:56:14 setup kernel: 0 ( 0x7 ) Nov 22 19:56:14 setup kernel: Pending list: Nov 22 19:56:14 setup kernel: 7 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 19 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 6 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 15 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 10 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 11 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 12 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 5 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 13 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 4 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 3 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 2 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 1 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 0 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 9 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 8 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 14 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 30 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 31 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 25 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 26 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 27 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 28 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 29 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 20 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 21 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 22 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 23 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 24 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 16 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 17 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: 18 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x7] Nov 22 19:56:14 setup kernel: Total 32 Nov 22 19:56:14 setup kernel: Kernel Free SCB list: Nov 22 19:56:14 setup kernel: Sequencer Complete DMA-inprog list: Nov 22 19:56:14 setup kernel: Sequencer Complete list: Nov 22 19:56:14 setup kernel: Sequencer DMA-Up and Complete list: Nov 22 19:56:14 setup kernel: Nov 22 19:56:14 setup kernel: scsi1: FIFO0 Free, LONGJMP == 0x8251, SCB 0x11 Nov 22 19:56:14 setup kernel: SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x4] DFSTATUS[0x89] Nov 22 19:56:14 setup kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0] Nov 22 19:56:14 setup kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT = 0x0 Nov 22 19:56:15 setup kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10] [...] And so on, until the external SCSI devices become unusable. The system is still running on the internally connected SCSI drives, though. I found some messages reporting similar problems on this list, a few weeks ago (beginning of October 2005). There was also a patch for the aic79xx driver mentioned, but I haven't found any report about it since then, so I don't know the status of the patch (it was for the 2.6 kernel, anyway, as far as I remember) What can I do to make the external RAID usable? Dump the Adaptec cards and replace them with something better? Patch the driver? Any help is appreciated! Thanks! - - andreas - -- Andreas Haumer | mailto:andreas@xss.co.at *x Software + Systeme | http://www.xss.co.at/ Karmarschgasse 51/2/20 | Tel: +43-1-6060114-0 A-1100 Vienna, Austria | Fax: +43-1-6060114-71 -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.2 (GNU/Linux) Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org iD8DBQFDg47JxJmyeGcXPhERAmHJAKDDneUcGWBG/DO6BmErT+EFm3WDUgCfYrW7 jjGW+en9tiILjo5XhcFa5Cc= =GR+f -----END PGP SIGNATURE----- - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/