Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
MIME-Version: 1.0
References: <20190808202415.25166-1-stephend@silicom-usa.com>
 <20190810074317.GA18582@infradead.org> <abfa4b20-2916-d89a-f4d3-b27fca5906b2@silicom-usa.com>
In-Reply-To: <abfa4b20-2916-d89a-f4d3-b27fca5906b2@silicom-usa.com>
From:   Dan Williams <dan.j.williams@intel.com>
Date:   Mon, 12 Aug 2019 09:29:11 -0700
Message-ID: <CAPcyv4g+PdbisZd8=FpB5QiR_FCA2OQ9EqEF9yMAN=XWTYXY1Q@mail.gmail.com>
Subject: Re: [PATCH] ata: ahci: Lookup PCS register offset based on PCI device ID
To:     Stephen Douthit <stephend@silicom-usa.com>
Cc:     Christoph Hellwig <hch@infradead.org>,
        Jens Axboe <axboe@kernel.dk>,
        "linux-ide@vger.kernel.org" <linux-ide@vger.kernel.org>,
        "linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Content-Type: text/plain; charset="UTF-8"
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

On Mon, Aug 12, 2019 at 6:03 AM Stephen Douthit
<stephend@silicom-usa.com> wrote:
>
> On 8/10/19 3:43 AM, Christoph Hellwig wrote:
> > On Thu, Aug 08, 2019 at 08:24:31PM +0000, Stephen Douthit wrote:
> >> Intel moved the PCS register from 0x92 to 0x94 on Denverton for some
> >> reason, so now we get to check the device ID before poking it on reset.
> >
> > And now you just match on the new IDs, which means we'll perpetually
> > catch up on any new device.  Dan, can you reach out inside Intel to
> > figure out if there is a way to find out the PCS register location
> > without the PCI ID check?
> >
> >
> >>   static int ahci_pci_reset_controller(struct ata_host *host)
> >>   {
> >>      struct pci_dev *pdev = to_pci_dev(host->dev);
> >> @@ -634,13 +669,14 @@ static int ahci_pci_reset_controller(struct ata_host *host)
> >>
> >>      if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
> >>              struct ahci_host_priv *hpriv = host->private_data;
> >> +            int pcs = ahci_pcs_offset(host);
> >>              u16 tmp16;
> >>
> >>              /* configure PCS */
> >> -            pci_read_config_word(pdev, 0x92, &tmp16);
> >> +            pci_read_config_word(pdev, pcs, &tmp16);
> >>              if ((tmp16 & hpriv->port_map) != hpriv->port_map) {
> >> -                    tmp16 |= hpriv->port_map;
> >> -                    pci_write_config_word(pdev, 0x92, tmp16);
> >> +                    tmp16 |= hpriv->port_map & 0xff;
> >> +                    pci_write_config_word(pdev, pcs, tmp16);
> >>              }
> >>      }
> >
> > And Stephen, while you are at it, can you split this Intel-specific
> > quirk into a separate helper?
>
> I can do that.  I'll wait until we hear back from Dan if there's a
> better scheme than a device ID lookup.

Do you see any behavior change in practice with this patch? It's
purportedly to re-enable the ports after a reset, but that would only
be needed if the entire pci device reset. In this path the reset is
being performed via the host control register. That is only meant to
touch mmio registers, not config registers. So, as far as I can see
this register bit twiddling after reset has never been necessary.