Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
MIME-Version: 1.0
References: <5143724.5TqzkYX0oI@dabox>
In-Reply-To: <5143724.5TqzkYX0oI@dabox>
From:   Masahiro Yamada <yamada.masahiro@socionext.com>
Date:   Tue, 10 Sep 2019 16:16:37 +0900
Message-ID: <CAK7LNAR8xtURiCoJC0eWLFw0q+78Eb_axoOzWH+JNugf-24Qig@mail.gmail.com>
Subject: Re: mtd raw nand denali.c broken for Intel/Altera Cyclone V
To:     Tim Sander <tim@krieglstein.org>
Cc:     Vignesh Raghavendra <vigneshr@ti.com>,
        Dinh Nguyen <dinguyen@kernel.org>,
        Richard Weinberger <richard@nod.at>,
        Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
        Marek Vasut <marek.vasut@gmail.com>,
        linux-mtd <linux-mtd@lists.infradead.org>,
        Miquel Raynal <miquel.raynal@bootlin.com>,
        Brian Norris <computersforpeace@gmail.com>,
        David Woodhouse <dwmw2@infradead.org>
Content-Type: text/plain; charset="UTF-8"
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

On Fri, Sep 6, 2019 at 9:39 PM Tim Sander <tim@krieglstein.org> wrote:
>
> Hi
>
> I have noticed that there multiple breakages piling up for the denali nand
> driver on the Intel/Altera Cyclone V. Unfortunately i had no time to track the
> mainline kernel closely. So the breakage seems to pile up. I am a little
> disapointed that Intel is not on the lookout that the kernel works on the
> chips they are selling. I was really happy about the state of the platform
> before concerning mainline support.
>
> The failure starts with kernel 4.19 or stable kernel release 4.18.19. The
> commit is ba4a1b62a2d742df9e9c607ac53b3bf33496508f.


Just for clarification, this corresponds to
0d55c668b218a1db68b5044bce4de74e1bd0f0c8 upstream.


> The problem here is that
> our platform works with a zero in the SPARE_AREA_SKIP_BYTES register.

Please clarify the scope of "our platform".
(Only you, or your company, or every individual using this chip?)


First, SPARE_AREA_SKIP_BYTES is not the property of the hardware.
Rather, it is about the OOB layout, in other words, this parameter
is defined by software.

For example, U-Boot supports the Denali NAND driver.
The SPARE_AREA_SKIP_BYTES is a user-configurable parameter:
https://github.com/u-boot/u-boot/blob/v2019.10-rc3/drivers/mtd/nand/raw/Kconfig#L112


Your platform works with a zero in the SPARE_AREA_SKIP_BYTES register
because the NAND chip on the board was initialized with a zero
set to the SPARE_AREA_SKIP_BYTES register.

If the NAND chip had been initialized with 8
set to the SPARE_AREA_SKIP_BYTES register, it would have
been working with 8 to the SPARE_AREA_SKIP_BYTES.

The Boot ROM is the only (semi-)software that is unconfigurable by users,
so the value of SPARE_AREA_SKIP_BYTES should be aligned with
the boot ROM.
I recommend you to check the spec of the boot ROM.

(The maintainer of the platform, Dihn is CC'ed,
so I hope he will jump in)


Second, I doubt 0 is a good value for SPARE_AREA_SKIP_BYTES.

As explained in commit log, SPARE_AREA_SKIP_BYTES==0 means
the OOB is used for ECC without any offset.
So, the BBM marked in the factory will be destroyed.


> But in
> this case the patch assumes the default value 8 which is straight out  wrong
> on this variant. Without this patch reverted all blocks of the nand flash are
> beeing marked bad :-(.
>
> When reverting the patch ba4a1b62a2d742df9e9c607ac53b3bf33496508f  i can boot
> 4.19.10 again.
>
> With 5.0 the it goes further down the drain and i didn't manage to boot it
> even with the above patch reverted.
>
> I also tried 5.3-rc7 with the above patch reverted and the variable t_x dirty hacked to the
> value 0x1388 as i got the impression that the timing calculation is off too. I still get an
> interrupt error and boot failure:

git-bisect is a general solution to pin point the problem.

BTW, if you end up with hacking the clock frequency, something is already wrong.

denali->clk_rate, denali->clk_x_rate should be 50MHz, 200MHz, respectively.

If not, please check the clock driver and your DT.


> [    0.817588] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
> [    0.823946] nand: Micron MT29F2G08ABAEAWP
> [    0.827965] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
> [    1.887052] denali-nand-dt ff900000.nand: timeout while waiting for irq 0x1000
> [    2.911056] denali-nand-dt ff900000.nand: timeout while waiting for irq 0x1000
>
> I have seen this https://lore.kernel.org/patchwork/patch/983055/ thread and
> this might fix at least the 4.19 boot problem.
>
> I would be really happy for hints how to get the Intel Cyclone V working again.
>
> Best regards
> Tim
>
>
>
>
> ______________________________________________________
> Linux MTD discussion mailing list
> http://lists.infradead.org/mailman/listinfo/linux-mtd/


-- 
Best Regards
Masahiro Yamada