Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
IronPort-SDR: Ri63J7Aw6uMGMaKnhSMcHacbpjjmbEpNbp0lA+lRpSBZWZ+fEZRN+FwrTUBPe5zbbvdVs6pezi
 Bol0g/ndn7RC3f5YJj9VOayAvWmO02jMVft7VRJi4i97g9eN98k3DYNhXvPYBOQNqy1T2+HfeN
 m6J+5J2ZwWEeAKy/Ndfc5ZVSHRXL2OvDPBi16Y/2eNOeih5HSQ76aixS/BKaQA+m8a/lQg2n1A
 PHl/QA2x8v+pThueahwQTiyressiIZxkmPy5kWba/9cW+P6bVrNxQu8HU5CadjbUVblkUIgIQ+
 fhDmDQWWem2W8teNFvrXGSzX
From:   Ram Prakash Gupta <rampraka@codeaurora.org>
To:     asutoshd@codeaurora.org, stummala@codeaurora.org,
        sayalil@codeaurora.org, rampraka@codeaurora.org,
        vbadigan@codeaurora.org, cang@codeaurora.org, ppvk@codeaurora.org,
        adrian.hunter@intel.com, ulf.hansson@linaro.org,
        robh+dt@kernel.org, linux-mmc@vger.kernel.org,
        linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: [RFC 6/6] dt-bindings: mmc: sdhci-msm: Add clk scaling dt parameters
Date:   Mon, 21 Oct 2019 19:59:37 +0530
Message-Id: <1571668177-3766-7-git-send-email-rampraka@codeaurora.org>
In-Reply-To: <1571668177-3766-1-git-send-email-rampraka@codeaurora.org>
References: <1571668177-3766-1-git-send-email-rampraka@codeaurora.org>
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

Adding clk scaling dt parameters.

Signed-off-by: Ram Prakash Gupta <rampraka@codeaurora.org>
---
 Documentation/devicetree/bindings/mmc/sdhci-msm.txt | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
index da4edb1..afaf88d 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
@@ -39,6 +39,21 @@ Required properties:
 	"cal"	- reference clock for RCLK delay calibration (optional)
 	"sleep"	- sleep clock for RCLK delay calibration (optional)
 
+Optional properties:
+- devfreq,freq-table - specifies supported frequencies for clock scaling.
+	Clock scaling logic shall toggle between these frequencies based
+	on card load. In case the defined frequencies are over or below
+	the supported card frequencies, they will be overridden
+	during card init. In case this entry is not supplied,
+	the driver will construct one based on the card
+	supported max and min frequencies.
+	The frequencies must be ordered from lowest to highest.
+
+- scaling-lower-bus-speed-mode - Few hosts can support DDR52 mode at the
+	same lower system voltage corner as high-speed mode. In such
+	cases, it is always better to put it in DDR  mode which will
+	improve the performance without any power impact.
+
 Example:
 
 	sdhc_1: sdhci@f9824900 {
@@ -56,6 +71,10 @@ Example:
 
 		clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>;
 		clock-names = "core", "iface";
+
+		devfreq,freq-table = <50000000 200000000>;
+		scaling-lower-bus-speed-mode = "DDR52"
+
 	};
 
 	sdhc_2: sdhci@f98a4900 {
-- 
1.9.1