Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
Date:   Sun, 27 Oct 2019 10:36:35 +0100
From:   Stephan Gerhold <stephan@gerhold.net>
To:     Linus Walleij <linus.walleij@linaro.org>
Cc:     lee.jones@linaro.org, linux-kernel@vger.kernel.org, arm@kernel.org
Subject: Re: [PATCH v3] mfd: db8500-prcmu: Support U8420-sysclk firmware
Message-ID: <20191027093635.GA3357@gerhold.net>
References: <20191026214732.17725-1-linus.walleij@linaro.org>
MIME-Version: 1.0
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
In-Reply-To: <20191026214732.17725-1-linus.walleij@linaro.org>
User-Agent: Mutt/1.12.2 (2019-09-21)
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

On Sat, Oct 26, 2019 at 11:47:32PM +0200, Linus Walleij wrote:
> There is a distinct version of the Ux500 U8420 variant
> with "sysclk", as can be seen from the vendor code that
> didn't make it upstream, this firmware lacks the
> ULPPLL (ultra-low power phase locked loop) which in
> effect means that the timer clock is instead wired to
> the 32768 Hz always-on clock.
> 
> This has some repercussions when enabling the timer
> clock as the code as it stands will disable the timer
> clock on these platforms (lacking the so-called
> "doze mode") and obtaining the wrong rate of the timer
> clock.
> 
> The timer frequency is of course needed very early in
> the boot, and as a consequence, we need to shuffle
> around the early PRCMU init code: whereas in the past
> we did not need to look up the PRCMU firmware version
> in the early init, but now we need to know the version
> before the core system timers are registered so we
> restructure the platform callbacks to the PRCMU so as
> not to take any arguments and instead look up the
> resources it needs directly from the device tree
> when initializing.
> 
> As we do not yet support any platforms using this
> firmware it is not a regression, but as PostmarketOS
> is starting to support products with this firmware we
> need to fix this up.
> 
> The low rate of 32kHz also makes the MTU timer unsuitable
> as delay timer but this needs to be fixed in a separate
> patch.
> 
> Cc: arm@kernel.org
> Cc: Lee Jones <lee.jones@linaro.org>
> Cc: Stephan Gerhold <stephan@gerhold.net>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Reviewed-by: Stephan Gerhold <stephan@gerhold.net>

> ---
> ChangeLog v2->v3:
> - It's a bad idead to return -ENODEV in a function
>   that returns void.
> ChangeLog v1->v2:
> - Change the style of the ULPPLL check function (more
>   compact)
> - Fix a missing of_node_put() by actually returning
>   with -ENODEV on error.
> 
> ARM SoC folks: as this mostly affects the MFD subsystems
> I think it'd be best if Lee can merge it, I do not
> plan any other changes to the ARM core files that the
> patch touches.
> ---
>  arch/arm/mach-ux500/cpu-db8500.c |  2 +-
>  drivers/mfd/db8500-prcmu.c       | 63 ++++++++++++++++++++++----------
>  include/linux/mfd/db8500-prcmu.h |  4 +-
>  include/linux/mfd/dbx500-prcmu.h |  7 ++--
>  4 files changed, 50 insertions(+), 26 deletions(-)
> 
> diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
> index 3875027ef8fc..e929aaa744c0 100644
> --- a/arch/arm/mach-ux500/cpu-db8500.c
> +++ b/arch/arm/mach-ux500/cpu-db8500.c
> @@ -84,6 +84,7 @@ static void __init ux500_init_irq(void)
>  	struct resource r;
>  
>  	irqchip_init();
> +	prcmu_early_init();
>  	np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
>  	of_address_to_resource(np, 0, &r);
>  	of_node_put(np);
> @@ -91,7 +92,6 @@ static void __init ux500_init_irq(void)
>  		pr_err("could not find PRCMU base resource\n");
>  		return;
>  	}
> -	prcmu_early_init(r.start, r.end-r.start);
>  	ux500_pm_init(r.start, r.end-r.start);
>  
>  	/* Unlock before init */
> diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
> index 9df365a15303..30f6558c691c 100644
> --- a/drivers/mfd/db8500-prcmu.c
> +++ b/drivers/mfd/db8500-prcmu.c
> @@ -27,6 +27,7 @@
>  #include <linux/bitops.h>
>  #include <linux/fs.h>
>  #include <linux/of.h>
> +#include <linux/of_address.h>
>  #include <linux/of_irq.h>
>  #include <linux/platform_device.h>
>  #include <linux/uaccess.h>
> @@ -668,6 +669,14 @@ struct prcmu_fw_version *prcmu_get_fw_version(void)
>  	return fw_info.valid ? &fw_info.version : NULL;
>  }
>  
> +static bool prcmu_is_ulppll_disabled(void)
> +{
> +	struct prcmu_fw_version *ver;
> +
> +	ver = prcmu_get_fw_version();
> +	return ver && ver->project == PRCMU_FW_PROJECT_U8420_SYSCLK;
> +}
> +
>  bool prcmu_has_arm_maxopp(void)
>  {
>  	return (readb(tcdm_base + PRCM_AVS_VARM_MAX_OPP) &
> @@ -1308,10 +1317,23 @@ static int request_sysclk(bool enable)
>  
>  static int request_timclk(bool enable)
>  {
> -	u32 val = (PRCM_TCR_DOZE_MODE | PRCM_TCR_TENSEL_MASK);
> +	u32 val;
> +
> +	/*
> +	 * On the U8420_CLKSEL firmware, the ULP (Ultra Low Power)
> +	 * PLL is disabled so we cannot use doze mode, this will
> +	 * stop the clock on this firmware.
> +	 */
> +	if (prcmu_is_ulppll_disabled())
> +		val = 0;
> +	else
> +		val = (PRCM_TCR_DOZE_MODE | PRCM_TCR_TENSEL_MASK);
>  
>  	if (!enable)
> -		val |= PRCM_TCR_STOP_TIMERS;
> +		val |= PRCM_TCR_STOP_TIMERS |
> +			PRCM_TCR_DOZE_MODE |
> +			PRCM_TCR_TENSEL_MASK;
> +
>  	writel(val, PRCM_TCR);
>  
>  	return 0;
> @@ -1615,7 +1637,8 @@ unsigned long prcmu_clock_rate(u8 clock)
>  	if (clock < PRCMU_NUM_REG_CLOCKS)
>  		return clock_rate(clock);
>  	else if (clock == PRCMU_TIMCLK)
> -		return ROOT_CLOCK_RATE / 16;
> +		return prcmu_is_ulppll_disabled() ?
> +			32768 : ROOT_CLOCK_RATE / 16;
>  	else if (clock == PRCMU_SYSCLK)
>  		return ROOT_CLOCK_RATE;
>  	else if (clock == PRCMU_PLLSOC0)
> @@ -2646,6 +2669,8 @@ static char *fw_project_name(u32 project)
>  		return "U8520 MBL";
>  	case PRCMU_FW_PROJECT_U8420:
>  		return "U8420";
> +	case PRCMU_FW_PROJECT_U8420_SYSCLK:
> +		return "U8420-sysclk";
>  	case PRCMU_FW_PROJECT_U9540:
>  		return "U9540";
>  	case PRCMU_FW_PROJECT_A9420:
> @@ -2693,27 +2718,18 @@ static int db8500_irq_init(struct device_node *np)
>  	return 0;
>  }
>  
> -static void dbx500_fw_version_init(struct platform_device *pdev,
> -			    u32 version_offset)
> +static void dbx500_fw_version_init(struct device_node *np)
>  {
> -	struct resource *res;
>  	void __iomem *tcpm_base;
>  	u32 version;
>  
> -	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
> -					   "prcmu-tcpm");
> -	if (!res) {
> -		dev_err(&pdev->dev,
> -			"Error: no prcmu tcpm memory region provided\n");
> -		return;
> -	}
> -	tcpm_base = ioremap(res->start, resource_size(res));
> +	tcpm_base = of_iomap(np, 1);
>  	if (!tcpm_base) {
> -		dev_err(&pdev->dev, "no prcmu tcpm mem region provided\n");
> +		pr_err("no prcmu tcpm mem region provided\n");
>  		return;
>  	}
>  
> -	version = readl(tcpm_base + version_offset);
> +	version = readl(tcpm_base + DB8500_PRCMU_FW_VERSION_OFFSET);
>  	fw_info.version.project = (version & 0xFF);
>  	fw_info.version.api_version = (version >> 8) & 0xFF;
>  	fw_info.version.func_version = (version >> 16) & 0xFF;
> @@ -2731,7 +2747,7 @@ static void dbx500_fw_version_init(struct platform_device *pdev,
>  	iounmap(tcpm_base);
>  }
>  
> -void __init db8500_prcmu_early_init(u32 phy_base, u32 size)
> +void __init db8500_prcmu_early_init(void)
>  {
>  	/*
>  	 * This is a temporary remap to bring up the clocks. It is
> @@ -2740,9 +2756,17 @@ void __init db8500_prcmu_early_init(u32 phy_base, u32 size)
>  	 * clock driver can probe independently. An early initcall will
>  	 * still be needed, but it can be diverted into drivers/clk/ux500.
>  	 */
> -	prcmu_base = ioremap(phy_base, size);
> -	if (!prcmu_base)
> +	struct device_node *np;
> +
> +	np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
> +	prcmu_base = of_iomap(np, 0);
> +	if (!prcmu_base) {
> +		of_node_put(np);
>  		pr_err("%s: ioremap() of prcmu registers failed!\n", __func__);
> +		return;
> +	}
> +	dbx500_fw_version_init(np);
> +	of_node_put(np);
>  
>  	spin_lock_init(&mb0_transfer.lock);
>  	spin_lock_init(&mb0_transfer.dbb_irqs_lock);
> @@ -3108,7 +3132,6 @@ static int db8500_prcmu_probe(struct platform_device *pdev)
>  		return -ENOMEM;
>  	}
>  	init_prcm_registers();
> -	dbx500_fw_version_init(pdev, DB8500_PRCMU_FW_VERSION_OFFSET);
>  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu-tcdm");
>  	if (!res) {
>  		dev_err(&pdev->dev, "no prcmu tcdm region provided\n");
> diff --git a/include/linux/mfd/db8500-prcmu.h b/include/linux/mfd/db8500-prcmu.h
> index 813710aa2cfd..1fc75d2b4a38 100644
> --- a/include/linux/mfd/db8500-prcmu.h
> +++ b/include/linux/mfd/db8500-prcmu.h
> @@ -489,7 +489,7 @@ struct prcmu_auto_pm_config {
>  
>  #ifdef CONFIG_MFD_DB8500_PRCMU
>  
> -void db8500_prcmu_early_init(u32 phy_base, u32 size);
> +void db8500_prcmu_early_init(void);
>  int prcmu_set_rc_a2p(enum romcode_write);
>  enum romcode_read prcmu_get_rc_p2a(void);
>  enum ap_pwrst prcmu_get_xp70_current_state(void);
> @@ -546,7 +546,7 @@ void db8500_prcmu_write_masked(unsigned int reg, u32 mask, u32 value);
>  
>  #else /* !CONFIG_MFD_DB8500_PRCMU */
>  
> -static inline void db8500_prcmu_early_init(u32 phy_base, u32 size) {}
> +static inline void db8500_prcmu_early_init(void) {}
>  
>  static inline int prcmu_set_rc_a2p(enum romcode_write code)
>  {
> diff --git a/include/linux/mfd/dbx500-prcmu.h b/include/linux/mfd/dbx500-prcmu.h
> index 238401a50d0b..e2571040c7e8 100644
> --- a/include/linux/mfd/dbx500-prcmu.h
> +++ b/include/linux/mfd/dbx500-prcmu.h
> @@ -190,6 +190,7 @@ enum ddr_pwrst {
>  #define PRCMU_FW_PROJECT_U8500_MBL2	12 /* Customer specific */
>  #define PRCMU_FW_PROJECT_U8520		13
>  #define PRCMU_FW_PROJECT_U8420		14
> +#define PRCMU_FW_PROJECT_U8420_SYSCLK	17
>  #define PRCMU_FW_PROJECT_A9420		20
>  /* [32..63] 9540 and derivatives */
>  #define PRCMU_FW_PROJECT_U9540		32
> @@ -211,9 +212,9 @@ struct prcmu_fw_version {
>  
>  #if defined(CONFIG_UX500_SOC_DB8500)
>  
> -static inline void prcmu_early_init(u32 phy_base, u32 size)
> +static inline void prcmu_early_init(void)
>  {
> -	return db8500_prcmu_early_init(phy_base, size);
> +	return db8500_prcmu_early_init();
>  }
>  
>  static inline int prcmu_set_power_state(u8 state, bool keep_ulp_clk,
> @@ -401,7 +402,7 @@ static inline int prcmu_config_a9wdog(u8 num, bool sleep_auto_off)
>  }
>  #else
>  
> -static inline void prcmu_early_init(u32 phy_base, u32 size) {}
> +static inline void prcmu_early_init(void) {}
>  
>  static inline int prcmu_set_power_state(u8 state, bool keep_ulp_clk,
>  	bool keep_ap_pll)
> -- 
> 2.21.0
>