Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
From:   Karl Palsson <karlp@tweak.net.au>
To:     mripard@kernel.org, wens@csie.org,
        linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org
Cc:     Karl Palsson <karlp@tweak.net.au>
Subject: [PATCHv2 1/2] ARM: dts: sun8i: add FriendlyARM NanoPi Duo2
Date:   Fri,  1 Nov 2019 20:55:35 +0000
Message-Id: <20191101205535.7896-1-karlp@tweak.net.au>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

This is an Allwinner H3 based board, with 512MB ram, a USB OTG port,
microsd slot, an onboard AP6212A wifi/bluetooth module, and a CSI
connector.

Full details and schematic available from vendor:
http://wiki.friendlyarm.com/wiki/index.php/NanoPi_Duo2

Signed-off-by: Karl Palsson <karlp@tweak.net.au>
---
Change since v1:
* dropped accidental commentary
* sorted nodes
* added enable gpio for vdd-cpu
* added vdd-dram and vcc-sys
* dropped default led trigger

 arch/arm/boot/dts/Makefile                 |   1 +
 arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts | 174 +++++++++++++++++++++
 2 files changed, 175 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9159fa2cea90..d8bf02abcda1 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1096,6 +1096,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-h3-beelink-x2.dtb \
 	sun8i-h3-libretech-all-h3-cc.dtb \
 	sun8i-h3-mapleboard-mp130.dtb \
+	sun8i-h3-nanopi-duo2.dtb \
 	sun8i-h3-nanopi-m1.dtb	\
 	sun8i-h3-nanopi-m1-plus.dtb \
 	sun8i-h3-nanopi-neo.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
new file mode 100644
index 000000000000..c73f59900975
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
@@ -0,0 +1,174 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Karl Palsson <karlp@tweak.net.au>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "FriendlyARM NanoPi Duo2";
+	compatible = "friendlyarm,nanopi-duo2", "allwinner,sun8i-h3";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr {
+			label = "nanopi:red:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+			default-state = "on";
+		};
+
+		status {
+			label = "nanopi:green:status";
+			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
+		};
+	};
+
+	r_gpio_keys {
+		compatible = "gpio-keys";
+
+		k1 {
+			label = "k1";
+			linux,code = <BTN_0>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
+		};
+	};
+
+	reg_vdd_cpux: vdd-cpux-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-ramp-delay = <50>; /* 4ms */
+
+		enable-active-high;
+		enable-gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+		gpios-states = <0x1>;
+		states = <1100000 0x0
+			  1300000 0x1>;
+	};
+
+	reg_vcc_dram: vcc-dram {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-dram";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+		vin-supply = <&reg_vcc5v0>;
+        };
+
+	reg_vdd_sys: vdd-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-sys";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		vin-supply = <&reg_vcc5v0>;
+        };
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
+	};
+
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+	vmmc-supply = <&reg_vcc3v3>;
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	sdio_wifi: sdio_wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&reg_usb0_vbus {
+	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>, <&uart2_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+		host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+		shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+	};
+};
+
+&usb_otg {
+	status = "okay";
+	dr_mode = "otg";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
-- 
2.20.1