Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
From:   Martin Blumenstingl <martin.blumenstingl@googlemail.com>
To:     andrew@lunn.ch, f.fainelli@gmail.com,
        linux-amlogic@lists.infradead.org, jianxin.pan@amlogic.com
Cc:     davem@davemloft.net, netdev@vger.kernel.org,
        linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
        Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Subject: [RFC v1 2/2] net: stmmac: dwmac-meson8b: add support for the RX delay configuration
Date:   Thu, 26 Dec 2019 21:36:55 +0100
Message-Id: <20191226203655.4046170-3-martin.blumenstingl@googlemail.com>
In-Reply-To: <20191226203655.4046170-1-martin.blumenstingl@googlemail.com>
References: <20191226203655.4046170-1-martin.blumenstingl@googlemail.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

DO NOT MERGE THIS!

Test results:
- Akaso M8S (not upstream yet) Meson8m2 with RMII PHY: no change
- Odroid-C1 Meson8b with RTL8211F RGMII PHY:
  phy-mode = "rgmii" still works
  phy-mode = "rgmii-id" works now
- Khadas VIM2 GXM with RTL8211F RGMII PHY:
  phy-mode = "rgmii" is now broken!
  phy-mode = "rgmii-id" works

The public A311D datasheet [0] mentions these bits in the PRG_ETH0 (also
call PRG_ETH0_REG) register:
- bit[13]: RMII & RGMII mode, Enable data delay adjustment and
  calibration logic.
- bit[14]: Set RXDV and RXD setup time, data is aligned with index 0.
  When set to 1, auto delay and skew.
- bit[19:15]:  Set bit14 to 0. RMII & RGMII mode. Capture input data at
  clock index equal to adj_delay.
- bit[24:20]: RMII & RGMII mode. 5 Bits correspondent to
  {RXDV, RXD[3:0]}, set to 1 will delay the data capture by 1 cycle.
(do all of these bits have the same meaning for all supported SoCs:
Meson8b, Meson8m2, GXBB, GXL, GXM, AXG, G12A, G12B, SM1?)

The public "Amlogic Ethernet controller user guide" recommends the
following settings.
RMII: adj_enable = 1, adj_setup = 0, adj_delay = 18, adj_skew = 0x0
RGMII: adj_enable = 1, adj_setup = 1, adj_delay = 4, adj_skew = 0xc
(shouldn't adj_delay be 0 for the RGMII mode based on the register
description above?)

Do we need to expose adj_delay and adj_skew to devicetree?
How do I know which value to set for each board?

[0] https://dl.khadas.com/Hardware/VIM3/Datasheet/A311D_Datasheet_01_Wesion.pdf
[1] http://openlinux.amlogic.com/@api/deki/files/75/=Amlogic_Ethenet_controller_user_Guide.pdf

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 .../ethernet/stmicro/stmmac/dwmac-meson8b.c   | 59 ++++++++++---------
 1 file changed, 32 insertions(+), 27 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
index 1483761ab1e6..af25eb1aea41 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-meson8b.c
@@ -33,6 +33,10 @@
 #define PRG_ETH0_CLK_M250_SEL_SHIFT	4
 #define PRG_ETH0_CLK_M250_SEL_MASK	GENMASK(4, 4)
 
+/* TX clock delay in ns = "8ns / 4 * tx_dly_val" (where 8ns are exactly one
+ * cycle of the 125MHz RGMII TX clock):
+ * 0ns = 0x0, 2ns = 0x1, 4ns = 0x2, 6ns = 0x3
+ */
 #define PRG_ETH0_TXDLY_MASK		GENMASK(6, 5)
 
 /* divider for the result of m250_sel */
@@ -44,6 +48,11 @@
 #define PRG_ETH0_INVERTED_RMII_CLK	BIT(11)
 #define PRG_ETH0_TX_AND_PHY_REF_CLK	BIT(12)
 
+#define PRG_ETH0_ADJ_ENABLE		BIT(13)
+#define PRG_ETH0_ADJ_SETUP		BIT(14)
+#define PRG_ETH0_ADJ_DELAY		GENMASK(19, 15)
+#define PRG_ETH0_ADJ_SKEW		GENMASK(24, 20)
+
 #define MUX_CLK_NUM_PARENTS		2
 
 struct meson8b_dwmac;
@@ -241,29 +250,38 @@ static int meson_axg_set_phy_mode(struct meson8b_dwmac *dwmac)
 
 static int meson8b_init_prg_eth(struct meson8b_dwmac *dwmac)
 {
+	u8 tx_dly_val = dwmac->tx_delay_ns >> 1;
+	u32 delay_config;
 	int ret;
-	u8 tx_dly_val = 0;
 
 	switch (dwmac->phy_mode) {
 	case PHY_INTERFACE_MODE_RGMII:
+		delay_config = FIELD_PREP(PRG_ETH0_TXDLY_MASK, tx_dly_val);
+		delay_config |= PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP;
+		break;
 	case PHY_INTERFACE_MODE_RGMII_RXID:
-		/* TX clock delay in ns = "8ns / 4 * tx_dly_val" (where
-		 * 8ns are exactly one cycle of the 125MHz RGMII TX clock):
-		 * 0ns = 0x0, 2ns = 0x1, 4ns = 0x2, 6ns = 0x3
-		 */
-		tx_dly_val = dwmac->tx_delay_ns >> 1;
-		/* fall through */
-
-	case PHY_INTERFACE_MODE_RGMII_ID:
+		delay_config = FIELD_PREP(PRG_ETH0_TXDLY_MASK, tx_dly_val);
+		break;
 	case PHY_INTERFACE_MODE_RGMII_TXID:
+		delay_config = PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP;
+		break;
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RMII:
+	default:
+		delay_config = 0;
+		break;
+	};
+
+	meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK |
+				PRG_ETH0_ADJ_ENABLE | PRG_ETH0_ADJ_SETUP |
+				PRG_ETH0_ADJ_DELAY | PRG_ETH0_ADJ_SKEW,
+				delay_config);
+
+	if (phy_interface_mode_is_rgmii(dwmac->phy_mode)) {
 		/* only relevant for RMII mode -> disable in RGMII mode */
 		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
 					PRG_ETH0_INVERTED_RMII_CLK, 0);
 
-		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK,
-					FIELD_PREP(PRG_ETH0_TXDLY_MASK,
-						   tx_dly_val));
-
 		/* Configure the 125MHz RGMII TX clock, the IP block changes
 		 * the output automatically (= without us having to configure
 		 * a register) based on the line-speed (125MHz for Gbit speeds,
@@ -286,24 +304,11 @@ static int meson8b_init_prg_eth(struct meson8b_dwmac *dwmac)
 		devm_add_action_or_reset(dwmac->dev,
 					(void(*)(void *))clk_disable_unprepare,
 					dwmac->rgmii_tx_clk);
-		break;
-
-	case PHY_INTERFACE_MODE_RMII:
+	} else {
 		/* invert internal clk_rmii_i to generate 25/2.5 tx_rx_clk */
 		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0,
 					PRG_ETH0_INVERTED_RMII_CLK,
 					PRG_ETH0_INVERTED_RMII_CLK);
-
-		/* TX clock delay cannot be configured in RMII mode */
-		meson8b_dwmac_mask_bits(dwmac, PRG_ETH0, PRG_ETH0_TXDLY_MASK,
-					0);
-
-		break;
-
-	default:
-		dev_err(dwmac->dev, "unsupported phy-mode %s\n",
-			phy_modes(dwmac->phy_mode));
-		return -EINVAL;
 	}
 
 	/* enable TX_CLK and PHY_REF_CLK generator */
-- 
2.24.1