Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
From:   Christian Hewitt <christianshewitt@gmail.com>
To:     Rob Herring <robh+dt@kernel.org>,
        Mark Rutland <mark.rutland@arm.com>,
        Kevin Hilman <khilman@baylibre.com>,
        devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
        linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org
Cc:     Christian Hewitt <christianshewitt@gmail.com>,
        =?UTF-8?q?Andreas=20F=C3=A4rber?= <afaerber@suse.de>,
        =?UTF-8?q?Jer=C3=B4me=20Brunet?= <jbrunet@baylibre.com>
Subject: [PATCH v6 3/3] arm64: dts: meson: add support for the SmartLabs SML-5442TW
Date:   Sun,  1 Mar 2020 08:17:21 +0400
Message-Id: <1583036241-88937-4-git-send-email-christianshewitt@gmail.com>
In-Reply-To: <1583036241-88937-1-git-send-email-christianshewitt@gmail.com>
References: <1583036241-88937-1-git-send-email-christianshewitt@gmail.com>
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

The SmartLabs SML-5442TW is broadly similar to the P231 reference design
but with the following differences:

- The Yellow and Blue LEDs are available but disabled
- The Red and Green LEDs are used to signal off/on status
- uart_AO can be accessed after opening the case; soldered pins exist
- GPIOX_17 is forced high to enable the QCA9377 module

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 292 +++++++++++++++++++++
 2 files changed, 293 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index eef0045..6cf8c4a 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -27,6 +27,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-phicomm-n1.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
new file mode 100644
index 0000000..5fdf1ca
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ * Copyright (c) 2018 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905d.dtsi"
+
+/ {
+	compatible = "smartlabs,sml5442tw", "amlogic,s905d",
+		"amlogic,meson-gxl";
+	model = "SmartLabs SML-5442TW";
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		yellow {
+			label = "sml5442tw:yellow";
+			gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		blue {
+			label = "sml5442tw:blue";
+			gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		green {
+			label = "sml5442tw:green";
+			gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		red {
+			label = "sml5442tw:red";
+			gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	hdmi_5v: regulator-hdmi-5v {
+		compatible = "regulator-fixed";
+
+		regulator-name = "HDMI_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};
+
+/* This will enable the bluetooth module */
+&gpio {
+	bt-en {
+		gpio-hog;
+		gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "bt-en";
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&hdmi_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&i2c_A {
+	status = "okay";
+	pinctrl-0 = <&i2c_a_pins>;
+	pinctrl-names = "default";
+};
+
+&internal_phy {
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <100000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* This is connected to the Bluetooth module: */
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+/* This UART is brought out to the debug header */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0 {
+	status = "okay";
+};
-- 
2.7.4