Received-SPF: pass (google.com: best guess record for domain of linux-kernel-owner@vger.kernel.org designates 209.132.180.67 as permitted sender) client-ip=209.132.180.67;
From:   Madalin Bucur <madalin.bucur@oss.nxp.com>
To:     davem@davemloft.net, netdev@vger.kernel.org
Cc:     devicetree@vger.kernel.org, shawnguo@kernel.org,
        leoyang.li@nxp.com, robh+dt@kernel.org, mark.rutland@arm.com,
        linux-kernel@vger.kernel.org,
        Madalin Bucur <madalin.bucur@oss.nxp.com>
Subject: [PATCH net 3/3] arm64: dts: ls1046ardb: set RGMII interfaces to RGMII_ID mode
Date:   Fri, 13 Mar 2020 14:04:25 +0200
Message-Id: <1584101065-3482-4-git-send-email-madalin.bucur@oss.nxp.com>
In-Reply-To: <1584101065-3482-1-git-send-email-madalin.bucur@oss.nxp.com>
References: <1584101065-3482-1-git-send-email-madalin.bucur@oss.nxp.com>
Content-Type: text/plain; charset="us-ascii"
Reply-to: madalin.bucur@oss.nxp.com
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.

Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".

Changing the phy-connection-type to "rgmii-id" to address the issue.

Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
index dbc23d6cd3b4..d53ccc56bb63 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts
@@ -131,12 +131,12 @@
 &fman0 {
 	ethernet@e4000 {
 		phy-handle = <&rgmii_phy1>;
-		phy-connection-type = "rgmii";
+		phy-connection-type = "rgmii-id";
 	};
 
 	ethernet@e6000 {
 		phy-handle = <&rgmii_phy2>;
-		phy-connection-type = "rgmii";
+		phy-connection-type = "rgmii-id";
 	};
 
 	ethernet@e8000 {
-- 
2.1.0