Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1750918AbWB1Q3n (ORCPT ); Tue, 28 Feb 2006 11:29:43 -0500 Received: (majordomo@vger.kernel.org) by vger.kernel.org id S1751602AbWB1Q3n (ORCPT ); Tue, 28 Feb 2006 11:29:43 -0500 Received: from mtl.rackplans.net ([65.39.167.249]:49891 "HELO innerfire.net") by vger.kernel.org with SMTP id S1750918AbWB1Q3m (ORCPT ); Tue, 28 Feb 2006 11:29:42 -0500 Date: Tue, 28 Feb 2006 11:29:37 -0500 (EST) From: Gerhard Mack To: linux-kernel@vger.kernel.org Subject: 2.6.15.4 amd64 + tuplip multiport cards only work with irqpoll Message-ID: MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 22897 Lines: 444 hello, I have a an amd64 machine here that fails to bring up it's network interfaces without the "irqpoll" boot option.. if that option is not enabled I get: eth0: network connection up using port A speed: 100 autonegotiation: yes duplex mode: full flowctrl: symmetric irq moderation: disabled scatter-gather: enabled irq 17: nobody cared (try booting with the "irqpoll" option) Call Trace: {__report_bad_irq+48} {note_interrupt+122} {__do_IRQ+210} {do_IRQ+45} {ret_from_intr+0} {SkGeIsrOnePort+21} {handle_IRQ_event+41} {__do_IRQ+170} {do_IRQ+45} {ret_from_intr+0} {tulip_select_media+2030} {tulip_up+1969} {tulip_up+1967} {tulip_open+55} {dev_open+57} {dev_change_flags+87} {devinet_ioctl+647} {inet_ioctl+76} {sock_ioctl+426} {do_ioctl+41} {vfs_ioctl+415} {sys_ioctl+60} {system_call+126} handlers: [tulip_interrupt+0/2185] (tulip_interrupt+0x0/0x889) [tulip_interrupt+0/2185] (tulip_interrupt+0x0/0x889) Disabling IRQ #17 irq 18: nobody cared (try booting with the "irqpoll" option) Call Trace: {__report_bad_irq+48} {note_interrupt+122} {__do_IRQ+210} {do_IRQ+45} {ret_from_intr+0} handlers: [tulip_interrupt+0/2185] (tulip_interrupt+0x0/0x889) Feb 28 10:40:37 localhost last message repeated 2 times Disabling IRQ #18 irq 19: nobody cared (try booting with the "irqpoll" option) Call Trace: {__report_bad_irq+48} {note_interrupt+122} {__do_IRQ+210} {do_IRQ+45} {ret_from_intr+0} {thread_return+0} {default_idle+0} {default_idle+56} {cpu_idle+63} {start_kernel+360} {x86_64_start_kernel+381} handlers: [tulip_interrupt+0/2185] (tulip_interrupt+0x0/0x889) Feb 28 10:40:38 localhost last message repeated 3 times Disabling IRQ #19 gw-nat:~# cat /proc/interrupts CPU0 0: 385587 IO-APIC-edge timer 1: 8 IO-APIC-edge i8042 8: 0 IO-APIC-edge rtc 9: 0 IO-APIC-level acpi 14: 2151 IO-APIC-edge ide0 15: 20 IO-APIC-edge ide1 16: 2716 IO-APIC-level SysKonnect SK-98xx, eth2, eth6, eth9, eth16, eth19 17: 24 IO-APIC-level eth1, eth5, eth12, eth15, eth18 18: 12 IO-APIC-level eth3, eth7, eth10, eth13, eth20 19: 12 IO-APIC-level eth4, eth8, eth11, eth14, eth17 NMI: 101 LOC: 385436 ERR: 0 MIS: 0 Bootdata ok (command line is root=/dev/hda3 ro console=tty0 irqpoll) Linux version 2.6.15.4 (root@gw-nat) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #3 PREEMPT Tue Feb 28 10:57:30 EST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable) BIOS-e820: 000000003ffb0000 - 000000003ffc0000 (ACPI data) BIOS-e820: 000000003ffc0000 - 000000003fff0000 (ACPI NVS) BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fa880 ACPI: XSDT (v001 A M I OEMXSDT 0x11000503 MSFT 0x00000097) @ 0x000000003ffb0100 ACPI: FADT (v003 A M I OEMFACP 0x11000503 MSFT 0x00000097) @ 0x000000003ffb0290 ACPI: MADT (v001 A M I OEMAPIC 0x11000503 MSFT 0x00000097) @ 0x000000003ffb0390 ACPI: OEMB (v001 A M I OEMBIOS 0x11000503 MSFT 0x00000097) @ 0x000000003ffc0040 ACPI: DSDT (v001 A0277 A0277001 0x00000001 MSFT 0x0100000d) @ 0x0000000000000000 On node 0 totalpages: 257489 DMA zone: 3047 pages, LIFO batch:0 DMA32 zone: 254442 pages, LIFO batch:31 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:15 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:bf780000) Checking aperture... CPU 0: aperture @ e0000000 size 256 MB Built 1 zonelists Kernel command line: root=/dev/hda3 ro console=tty0 irqpoll Misrouted IRQ fixup and polling support enabled This may significantly impact system performance Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 3.579545 MHz PM timer. time.c: Detected 1802.324 MHz processor. time.c: Using PIT/TSC based timekeeping. Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Memory: 1027968k/1048256k available (2129k kernel code, 19608k reserved, 874k data, 156k init) Calibrating delay using timer specific routine.. 3611.86 BogoMIPS (lpj=1805932) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) mtrr: v2.0 (20020519) CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 02 Using local APIC timer interrupts. Detected 12.516 MHz APIC timer. testing NMI watchdog ... OK. NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:06:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 11 devices PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report agpgart: Detected AGP bridge 0 agpgart: AGP aperture is 256M @ 0xe0000000 PCI-DMA: Disabling IOMMU. pnp: 00:06: ioport range 0x680-0x6ff has been reserved pnp: 00:06: ioport range 0x290-0x297 has been reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: faf00000-fbffffff PREFETCH window: f0000000-f7ffffff PCI: Bridge: 0000:00:09.0 IO window: d000-efff MEM window: fa700000-faefffff PREFETCH window: disabled. PCI: Bridge: 0000:00:0b.0 IO window: b000-cfff MEM window: f9f00000-fa6fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:0c.0 IO window: 9000-afff MEM window: f9700000-f9efffff PREFETCH window: disabled. PCI: Bridge: 0000:00:0d.0 IO window: 7000-8fff MEM window: f8f00000-f96fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:0e.0 IO window: 5000-6fff MEM window: f8700000-f8efffff PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:01.0 to 64 IA-32 Microcode Update Driver: v1.14 io scheduler noop registered io scheduler cfq registered ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Sleep Button (CM) [SLPB] Real Time Clock Driver v1.12 Non-volatile memory driver v1.2 Linux agpgart interface v0.101 (c) Dave Jones Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). Hangcheck: Using monotonic_clock(). PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A loop: loaded (max 8 devices) ns83820.c: National Semiconductor DP83820 10/100/1000 driver. GSI 16 sharing vector 0xA9 and IRQ 16 ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 16 ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 16 eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter PrefPort:A RlmtMode:Check Link State Linux Tulip driver version 1.1.13 (May 11, 2002) GSI 17 sharing vector 0xB1 and IRQ 17 ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 16 (level, low) -> IRQ 17 tulip0: EEPROM default media type Autosense. tulip0: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip0: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip0: Advertising 01e1 on PHY 1, previously advertising 0101. eth1: Digital DS21140 Tulip rev 34 at ffffc20000004000, 00:00:D1:1F:E2:1D, IRQ 17. ACPI: PCI Interrupt 0000:05:05.0[A] -> GSI 17 (level, low) -> IRQ 16 tulip1: Controller 1 of multiport board. tulip1: EEPROM default media type Autosense. tulip1: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip1: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip1: Advertising 01e1 on PHY 1, previously advertising 0101. eth2: Digital DS21140 Tulip rev 34 at ffffc20000006000, EEPROM not present, 00:00:D1:1F:E2:1E, IRQ 16. GSI 18 sharing vector 0xB9 and IRQ 18 ACPI: PCI Interrupt 0000:05:06.0[A] -> GSI 18 (level, low) -> IRQ 18 tulip2: Controller 2 of multiport board. tulip2: EEPROM default media type Autosense. tulip2: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip2: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip2: Advertising 01e1 on PHY 1, previously advertising 0101. eth3: Digital DS21140 Tulip rev 34 at ffffc20000012000, EEPROM not present, 00:00:D1:1F:E2:1F, IRQ 18. GSI 19 sharing vector 0xC1 and IRQ 19 ACPI: PCI Interrupt 0000:05:07.0[A] -> GSI 19 (level, low) -> IRQ 19 tulip3: Controller 3 of multiport board. tulip3: EEPROM default media type Autosense. tulip3: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip3: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip3: Advertising 01e1 on PHY 1, previously advertising 0101. eth4: Digital DS21140 Tulip rev 34 at ffffc20000014000, EEPROM not present, 00:00:D1:1F:E2:20, IRQ 19. ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 16 (level, low) -> IRQ 17 tulip4: EEPROM default media type Autosense. tulip4: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip4: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip4: Advertising 01e1 on PHY 1, previously advertising 0101. eth5: Digital DS21140 Tulip rev 34 at ffffc20000016000, 00:00:D1:20:1C:2E, IRQ 17. ACPI: PCI Interrupt 0000:04:05.0[A] -> GSI 17 (level, low) -> IRQ 16 tulip5: Controller 1 of multiport board. tulip5: EEPROM default media type Autosense. tulip5: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip5: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip5: Advertising 01e1 on PHY 1, previously advertising 0101. eth6: Digital DS21140 Tulip rev 34 at ffffc2000001e000, EEPROM not present, 00:00:D1:20:1C:2F, IRQ 16. ACPI: PCI Interrupt 0000:04:06.0[A] -> GSI 18 (level, low) -> IRQ 18 tulip6: Controller 2 of multiport board. tulip6: EEPROM default media type Autosense. tulip6: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip6: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip6: Advertising 01e1 on PHY 1, previously advertising 0101. eth7: Digital DS21140 Tulip rev 34 at ffffc20000020000, EEPROM not present, 00:00:D1:20:1C:30, IRQ 18. ACPI: PCI Interrupt 0000:04:07.0[A] -> GSI 19 (level, low) -> IRQ 19 tulip7: Controller 3 of multiport board. tulip7: EEPROM default media type Autosense. tulip7: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip7: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip7: Advertising 01e1 on PHY 1, previously advertising 0101. eth8: Digital DS21140 Tulip rev 34 at ffffc20000022000, EEPROM not present, 00:00:D1:20:1C:31, IRQ 19. ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 17 (level, low) -> IRQ 16 tulip8: EEPROM default media type Autosense. tulip8: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip8: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip8: Advertising 01e1 on PHY 1, previously advertising 0101. eth9: Digital DS21140 Tulip rev 34 at ffffc20000024000, 00:00:D1:1E:50:CF, IRQ 16. ACPI: PCI Interrupt 0000:03:05.0[A] -> GSI 18 (level, low) -> IRQ 18 tulip9: Controller 1 of multiport board. tulip9: EEPROM default media type Autosense. tulip9: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip9: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip9: Advertising 01e1 on PHY 1, previously advertising 0101. eth10: Digital DS21140 Tulip rev 34 at ffffc20000026000, EEPROM not present, 00:00:D1:1E:50:D0, IRQ 18. ACPI: PCI Interrupt 0000:03:06.0[A] -> GSI 19 (level, low) -> IRQ 19 tulip10: Controller 2 of multiport board. tulip10: EEPROM default media type Autosense. tulip10: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip10: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip10: Advertising 01e1 on PHY 1, previously advertising 0101. eth11: Digital DS21140 Tulip rev 34 at ffffc20000028000, EEPROM not present, 00:00:D1:1E:50:D1, IRQ 19. ACPI: PCI Interrupt 0000:03:07.0[A] -> GSI 16 (level, low) -> IRQ 17 tulip11: Controller 3 of multiport board. tulip11: EEPROM default media type Autosense. tulip11: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip11: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip11: Advertising 01e1 on PHY 1, previously advertising 0101. eth12: Digital DS21140 Tulip rev 34 at ffffc2000002a000, EEPROM not present, 00:00:D1:1E:50:D2, IRQ 17. ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 18 (level, low) -> IRQ 18 tulip12: EEPROM default media type Autosense. tulip12: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip12: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip12: Advertising 01e1 on PHY 1, previously advertising 0101. eth13: Digital DS21140 Tulip rev 34 at ffffc2000002c000, 00:00:D1:1E:7F:6C, IRQ 18. ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 19 (level, low) -> IRQ 19 tulip13: Controller 1 of multiport board. tulip13: EEPROM default media type Autosense. tulip13: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip13: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip13: Advertising 01e1 on PHY 1, previously advertising 0101. eth14: Digital DS21140 Tulip rev 34 at ffffc2000002e000, EEPROM not present, 00:00:D1:1E:7F:6D, IRQ 19. ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 16 (level, low) -> IRQ 17 tulip14: Controller 2 of multiport board. tulip14: EEPROM default media type Autosense. tulip14: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip14: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip14: Advertising 01e1 on PHY 1, previously advertising 0101. eth15: Digital DS21140 Tulip rev 34 at ffffc20000030000, EEPROM not present, 00:00:D1:1E:7F:6E, IRQ 17. ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 17 (level, low) -> IRQ 16 tulip15: Controller 3 of multiport board. tulip15: EEPROM default media type Autosense. tulip15: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip15: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip15: Advertising 01e1 on PHY 1, previously advertising 0101. eth16: Digital DS21140 Tulip rev 34 at ffffc20000032000, EEPROM not present, 00:00:D1:1E:7F:6F, IRQ 16. ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 19 (level, low) -> IRQ 19 tulip16: EEPROM default media type Autosense. tulip16: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip16: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip16: Advertising 01e1 on PHY 1, previously advertising 0101. eth17: Digital DS21140 Tulip rev 34 at ffffc20000034000, 00:00:92:A7:8A:A0, IRQ 19. ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 16 (level, low) -> IRQ 17 tulip17: Controller 1 of multiport board. tulip17: EEPROM default media type Autosense. tulip17: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip17: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip17: Advertising 01e1 on PHY 1, previously advertising 0101. eth18: Digital DS21140 Tulip rev 34 at ffffc20000036000, EEPROM not present, 00:00:92:A7:8A:A1, IRQ 17. ACPI: PCI Interrupt 0000:01:06.0[A] -> GSI 17 (level, low) -> IRQ 16 tulip18: Controller 2 of multiport board. tulip18: EEPROM default media type Autosense. tulip18: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip18: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip18: Advertising 01e1 on PHY 1, previously advertising 0101. eth19: Digital DS21140 Tulip rev 34 at ffffc20000038000, EEPROM not present, 00:00:92:A7:8A:A2, IRQ 16. ACPI: PCI Interrupt 0000:01:07.0[A] -> GSI 18 (level, low) -> IRQ 18 tulip19: Controller 3 of multiport board. tulip19: EEPROM default media type Autosense. tulip19: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. tulip19: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip19: Advertising 01e1 on PHY 1, previously advertising 0101. eth20: Digital DS21140 Tulip rev 34 at ffffc2000003a000, EEPROM not present, 00:00:92:A7:8A:A3, IRQ 18. Linux video capture interface: v1.00 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 GSI 20 sharing vector 0xC9 and IRQ 20 ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 4 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: WDC WD800JB-00JJC0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: LTN486S, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hdc: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 mice: PS/2 mouse device common for all mice input: PC Speaker as /class/input/input0 I2O subsystem v1.288 i2o: max drivers = 8 I2O Configuration OSM v1.248 I2O Bus Adapter OSM v$Rev$ I2O Block Device OSM v1.287 I2O ProcFS OSM v1.145 i2c /dev entries driver input: AT Translated Set 2 keyboard as /class/input/input1 netem: version 1.1 u32 classifier OLD policer on Netfilter messages via NETLINK v0.30. NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered ip_conntrack version 2.4 (4094 buckets, 32752 max) - 312 bytes per conntrack ctnetlink v0.90: registering with nfnetlink. ip_conntrack_pptp version 3.1 loaded ip_nat_pptp version 3.0 loaded ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/ ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4) powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x6 (1400 mV) powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV) cpu_init done, current fid 0xa, vid 0x6 ACPI wakeup devices: PCI0 PS2K UAR1 AC97 USB1 USB2 USB3 USB4 EHCI PWRB SLPB ACPI: (supports S0 S1 S3 S4 S5) BIOS EDD facility v0.16 2004-Jun-25, 1 devices found ReiserFS: hda3: found reiserfs format "3.6" with standard journal ReiserFS: hda3: using ordered data mode ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda3: checking transaction log (hda3) ReiserFS: hda3: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 156k freed Adding 979956k swap on /dev/hda2. Priority:-1 extents:1 across:979956k ReiserFS: hda1: found reiserfs format "3.6" with standard journal ReiserFS: hda1: using ordered data mode ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda1: checking transaction log (hda1) ReiserFS: hda1: Using r5 hash to sort names eth0: network connection up using port A speed: 100 autonegotiation: yes duplex mode: full flowctrl: symmetric irq moderation: disabled scatter-gather: enabled -- Gerhard Mack gmack@innerfire.net <>< As a computer I find your faith in technology amusing. - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/