Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
From:   Miquel Raynal <miquel.raynal@bootlin.com>
To:     Masahiro Yamada <yamada.masahiro@socionext.com>,
        linux-mtd@lists.infradead.org
Cc:     Miquel Raynal <miquel.raynal@bootlin.com>,
        Marek Vasut <marex@denx.de>,
        Vignesh Raghavendra <vigneshr@ti.com>,
        Richard Weinberger <richard@nod.at>,
        linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2] mtd: rawnand: denali: add more delays before latching incoming data
Date:   Sun, 10 May 2020 22:06:35 +0200
Message-Id: <20200510200635.3080-1-miquel.raynal@bootlin.com>
In-Reply-To: <20200317071821.9916-1-yamada.masahiro@socionext.com>
References: 
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

On Tue, 2020-03-17 at 07:18:21 UTC, Masahiro Yamada wrote:
> The Denali IP have several registers to specify how many clock cycles
> should be waited between falling/rising signals. You can improve the
> NAND access performance by programming these registers with optimized
> values.
> 
> Because struct nand_sdr_timings represents the device requirement
> in pico seconds, denali_setup_data_interface() computes the register
> values by dividing the device timings with the clock period.
> 
> Marek Vasut reported this driver in the latest kernel does not work
> on his SOCFPGA board. (The on-board NAND chip is mode 5)
> 
> The suspicious parameter is acc_clks, so this commit relaxes it.
> 
> The Denali NAND Flash Memory Controller User's Guide describes this
> register as follows:
> 
>   acc_clks
>     signifies the number of bus interface clk_x clock cycles,
>     controller should wait from read enable going low to sending
>     out a strobe of clk_x for capturing of incoming data.
> 
> Currently, acc_clks is calculated only based on tREA, the delay on the
> chip side. This does not include additional delays that come from the
> data path on the PCB and in the SoC, load capacity of the pins, etc.
> 
> This relatively becomes a big factor on faster timing modes like mode 5.
> 
> Before supporting the ->setup_data_interface() hook (e.g. Linux 4.12),
> the Denali driver hacks acc_clks in a couple of ways [1] [2] to support
> the timing mode 5.
> 
> We would not go back to the hard-coded acc_clks, but we need to include
> this factor into the delay somehow. Let's say the amount of the additional
> delay is 10000 pico sec.
> 
> In the new calculation, acc_clks is determined by timings->tREA_max +
> data_setup_on_host.
> 
> Also, prolong the RE# low period to make sure the data hold is met.
> 
> Finally, re-center the data latch timing for extra safety.
> 
> [1] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L276
> [2] https://github.com/torvalds/linux/blob/v4.12/drivers/mtd/nand/denali.c#L282
> 
> Reported-by: Marek Vasut <marex@denx.de>
> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
> Tested-by: Marek Vasut <marex@denx.de>

Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next, thanks.

Miquel