Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1750867AbWCKPUu (ORCPT ); Sat, 11 Mar 2006 10:20:50 -0500 Received: (majordomo@vger.kernel.org) by vger.kernel.org id S1751189AbWCKPUu (ORCPT ); Sat, 11 Mar 2006 10:20:50 -0500 Received: from tirith.ics.muni.cz ([147.251.4.36]:45266 "EHLO tirith.ics.muni.cz") by vger.kernel.org with ESMTP id S1750867AbWCKPUt (ORCPT ); Sat, 11 Mar 2006 10:20:49 -0500 From: Jiri Slaby To: Andrew Morotn Cc: Linux kernel mailing list , htejun@gmail.com, jgarzik@pobox.com Subject: ata2: dev 0 failed to IDENTIFY (I/O error) [Was: 2.6.16-rc5-mm3] In-reply-to: <20060307021929.754329c9.akpm@osdl.org> Message-Id: Date: Sat, 11 Mar 2006 16:20:32 +0100 X-Muni-Spam-TestIP: 147.251.48.3 X-Muni-Envelope-From: xslaby@informatics.muni.cz X-Muni-Virus-Test: Clean Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 7699 Lines: 163 Hello, this is in diff between -mm2 and -mm3: ata2: SATA port has no device. ata2: PIO error ata2: dev 0 failed to IDENTIFY (I/O error) These lines are new in dmesg. Whole diff: --- mm2 2006-03-11 15:50:21.000000000 +0100 +++ mm3 2006-03-11 15:49:11.000000000 +0100 @@ -1,4 +1,4 @@ -Linux version 2.6.16-rc5-mm2 (ku@bellona) (gcc version 4.1.0 20060214 (Red Hat 4.1.0-0.27)) #101 SMP PREEMPT Fri Mar 3 16:20:18 CET 2006 +Linux version 2.6.16-rc5-mm3 (ku@bellona) (gcc version 4.1.0 20060214 (Red Hat 4.1.0-0.27)) #102 SMP PREEMPT Thu Mar 9 23:49:35 CET 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) @@ -38,7 +38,7 @@ Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) -Detected 2736.287 MHz processor. +Detected 2736.432 MHz processor. Built 1 zonelists Kernel command line: ro root=/dev/hda2 reboot=w mapped APIC to ffffd000 (fee00000) @@ -51,9 +51,9 @@ Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) -Memory: 514404k/524224k available (2532k kernel code, 9360k reserved, 1380k data, 200k init, 0k highmem) +Memory: 514404k/524224k available (2534k kernel code, 9360k reserved, 1378k data, 200k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. -Calibrating delay using timer specific routine.. 5476.83 BogoMIPS (lpj=10953674) +Calibrating delay using timer specific routine.. 5476.78 BogoMIPS (lpj=10953574) Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 @@ -71,7 +71,7 @@ Booting processor 1/1 eip 2000 CPU 1 irqstacks, hard=c0513000 soft=c0510000 Initializing CPU#1 -Calibrating delay using timer specific routine.. 5472.84 BogoMIPS (lpj=10945697) +Calibrating delay using timer specific routine.. 5472.77 BogoMIPS (lpj=10945557) CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K @@ -83,12 +83,12 @@ CPU1: Intel P4/Xeon Extended MCE MSRs (12) available CPU1: Thermal monitoring enabled CPU1: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09 -Total of 2 processors activated (10949.68 BogoMIPS). +Total of 2 processors activated (10949.56 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs -migration_cost=5 +migration_cost=145 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 @@ -170,6 +170,7 @@ hda: hda1 hda2 hda3 hda4 < hda5 hda6 > libata version 1.20 loaded. ata_piix 0000:00:1f.2: version 1.05 +ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0xC000 ctl 0xC402 bmdma 0xD000 irq 18 @@ -177,8 +178,12 @@ ata1: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:203f ata1: dev 0 ATA-6, max UDMA/100, 234441648 sectors: LBA48 ata1(0): applying bridge limits +ata1: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:203f ata1: dev 0 configured for UDMA/100 scsi0 : ata_piix +ata2: SATA port has no device. +ata2: PIO error +ata2: dev 0 failed to IDENTIFY (I/O error) scsi1 : ata_piix Vendor: ATA Model: WDC WD1200JD-00F Rev: 02.0 Type: Direct-Access ANSI SCSI revision: 05 @@ -203,7 +208,7 @@ usb usb1: new device found, idVendor=0000, idProduct=0000 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller -usb usb1: Manufacturer: Linux 2.6.16-rc5-mm2 ehci_hcd +usb usb1: Manufacturer: Linux 2.6.16-rc5-mm3 ehci_hcd usb usb1: SerialNumber: 0000:00:1d.7 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found @@ -217,7 +222,7 @@ usb usb2: new device found, idVendor=0000, idProduct=0000 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: UHCI Host Controller -usb usb2: Manufacturer: Linux 2.6.16-rc5-mm2 uhci_hcd +usb usb2: Manufacturer: Linux 2.6.16-rc5-mm3 uhci_hcd usb usb2: SerialNumber: 0000:00:1d.0 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found @@ -230,7 +235,7 @@ usb usb3: new device found, idVendor=0000, idProduct=0000 usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: UHCI Host Controller -usb usb3: Manufacturer: Linux 2.6.16-rc5-mm2 uhci_hcd +usb usb3: Manufacturer: Linux 2.6.16-rc5-mm3 uhci_hcd usb usb3: SerialNumber: 0000:00:1d.1 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found @@ -243,7 +248,7 @@ usb usb4: new device found, idVendor=0000, idProduct=0000 usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: UHCI Host Controller -usb usb4: Manufacturer: Linux 2.6.16-rc5-mm2 uhci_hcd +usb usb4: Manufacturer: Linux 2.6.16-rc5-mm3 uhci_hcd usb usb4: SerialNumber: 0000:00:1d.2 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found @@ -256,7 +261,7 @@ usb usb5: new device found, idVendor=0000, idProduct=0000 usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: UHCI Host Controller -usb usb5: Manufacturer: Linux 2.6.16-rc5-mm2 uhci_hcd +usb usb5: Manufacturer: Linux 2.6.16-rc5-mm3 uhci_hcd usb usb5: SerialNumber: 0000:00:1d.3 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found @@ -294,25 +299,25 @@ NET: Registered protocol family 17 Starting balanced_irq Using IPI Shortcut mode +Time: tsc clocksource has been installed. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 200k freed -Time: tsc clocksource has been installed. input: AT Translated Set 2 keyboard as /class/input/input1 -gameport: EMU10K1 is pci0000:02:02.1/gameport0, io 0xa400, speed 1065kHz hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) +gameport: EMU10K1 is pci0000:02:02.1/gameport0, io 0xa400, speed 1084kHz ieee1394: Initialized config rom entry `ip1394' ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 21 (level, low) -> IRQ 22 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22] MMIO=[fa004000-fa0047ff] Max Packet=[2048] IR/IT contexts=[4/8] Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE] +ieee1394: Host added: ID:BUS[0-00:1023] GUID[000d6100001a97a1] EXT3 FS on hda2, internal journal kjournald starting. Commit interval 5 seconds -ieee1394: Host added: ID:BUS[0-00:1023] GUID[000d6100001a97a1] EXT3 FS on hda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/