Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
Date:   Tue, 19 May 2020 14:33:38 +0200
From:   Johan Hovold <johan@kernel.org>
To:     mani@kernel.org
Cc:     johan@kernel.org, gregkh@linuxfoundation.org,
        linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
        patong.mxl@gmail.com
Subject: Re: [PATCH v3 1/2] usb: serial: Add MaxLinear/Exar USB to Serial
 driver
Message-ID: <20200519123338.GD27787@localhost>
References: <20200430184924.31690-1-mani@kernel.org>
 <20200430184924.31690-2-mani@kernel.org>
MIME-Version: 1.0
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
In-Reply-To: <20200430184924.31690-2-mani@kernel.org>
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

On Fri, May 01, 2020 at 12:19:23AM +0530, mani@kernel.org wrote:
> From: Manivannan Sadhasivam <mani@kernel.org>
> 
> Add support for MaxLinear/Exar USB to Serial converters. This driver
> only supports XR21V141X series but it can be extended to other series
> from Exar as well in future.
> 
> This driver is inspired from the initial one submitted by Patong Yang:
> 
> https://patchwork.kernel.org/patch/10543261/
> 
> While the initial driver was a custom tty USB driver exposing whole
> new serial interface ttyXRUSBn, this version is completely based on USB
> serial core thus exposing the interfaces as ttyUSBn. This will avoid
> the overhead of exposing a new USB serial interface which the userspace
> tools are unaware of.
> 
> Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
> ---
>  drivers/usb/serial/Kconfig     |   9 +
>  drivers/usb/serial/Makefile    |   1 +
>  drivers/usb/serial/xr_serial.c | 624 +++++++++++++++++++++++++++++++++
>  3 files changed, 634 insertions(+)
>  create mode 100644 drivers/usb/serial/xr_serial.c
> 
> diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
> index 25d7e0c36d38..8f6ad9f94735 100644
> --- a/drivers/usb/serial/Kconfig
> +++ b/drivers/usb/serial/Kconfig
> @@ -644,6 +644,15 @@ config USB_SERIAL_UPD78F0730
>  	  To compile this driver as a module, choose M here: the
>  	  module will be called upd78f0730.
>  
> +config USB_SERIAL_XR
> +	tristate "USB MaxLinear/Exar USB to Serial driver"
> +	help
> +	  Say Y here if you want to use MaxLinear/Exar USB to Serial converter
> +	  devices.
> +
> +	  To compile this driver as a module, choose M here: the
> +	  module will be called xr_serial.
> +
>  config USB_SERIAL_DEBUG
>  	tristate "USB Debugging Device"
>  	help
> diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile
> index 2d491e434f11..4f69c2a3aff3 100644
> --- a/drivers/usb/serial/Makefile
> +++ b/drivers/usb/serial/Makefile
> @@ -62,4 +62,5 @@ obj-$(CONFIG_USB_SERIAL_VISOR)			+= visor.o
>  obj-$(CONFIG_USB_SERIAL_WISHBONE)		+= wishbone-serial.o
>  obj-$(CONFIG_USB_SERIAL_WHITEHEAT)		+= whiteheat.o
>  obj-$(CONFIG_USB_SERIAL_XIRCOM)			+= keyspan_pda.o
> +obj-$(CONFIG_USB_SERIAL_XR)			+= xr_serial.o
>  obj-$(CONFIG_USB_SERIAL_XSENS_MT)		+= xsens_mt.o
> diff --git a/drivers/usb/serial/xr_serial.c b/drivers/usb/serial/xr_serial.c
> new file mode 100644
> index 000000000000..fdb9ddf8bd95
> --- /dev/null
> +++ b/drivers/usb/serial/xr_serial.c
> @@ -0,0 +1,624 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * MaxLinear/Exar USB to Serial driver
> + *
> + * Based on initial driver written by Patong Yang <patong.mxl@gmail.com>
> + *
> + * Copyright (c) 2020 Manivannan Sadhasivam <mani@kernel.org>
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/slab.h>
> +#include <linux/tty.h>
> +#include <linux/usb.h>
> +#include <linux/usb/serial.h>
> +
> +struct xr_uart_regs {
> +	u8 enable;
> +	u8 format;
> +	u8 flow_ctrl;
> +	u8 xon_char;
> +	u8 xoff_char;
> +	u8 loopback;
> +	u8 tx_break;
> +	u8 rs485_delay;
> +	u8 gpio_mode;
> +	u8 gpio_dir;
> +	u8 gpio_int_mask;
> +	u8 gpio_set;
> +	u8 gpio_clr;
> +	u8 gpio_status;
> +};
> +
> +struct xr_port_private {
> +	const struct xr_uart_regs *regs;
> +};
> +
> +struct xr_txrx_clk_mask {
> +	u16 tx;
> +	u16 rx0;
> +	u16 rx1;
> +};
> +
> +#define XR21V141X_ID			0x1410
> +#define XR_INT_OSC_HZ			48000000
> +
> +/* USB Requests */
> +#define XR_SET_XR21V141X		0
> +#define XR_GET_XR21V141X		1
> +
> +#define XR21V141X_CLOCK_DIVISOR_0	0x4
> +#define XR21V141X_CLOCK_DIVISOR_1	0x5
> +#define XR21V141X_CLOCK_DIVISOR_2	0x6
> +#define XR21V141X_TX_CLOCK_MASK_0	0x7
> +#define XR21V141X_TX_CLOCK_MASK_1	0x8
> +#define XR21V141X_RX_CLOCK_MASK_0	0x9
> +#define XR21V141X_RX_CLOCK_MASK_1	0xa
> +
> +/* XR21V141X register blocks */
> +#define XR21V141X_UART_REG_BLOCK	0
> +#define XR21V141X_URM_REG_BLOCK		4
> +#define XR21V141X_UART_CUSTOM_BLOCK	0x66
> +
> +/* XR21V141X UART Manager Registers */
> +#define XR21V141X_URM_FIFO_ENABLE_REG	0x10
> +#define XR21V141X_URM_ENABLE_TX_FIFO	0x1
> +#define XR21V141X_URM_ENABLE_RX_FIFO	0x2
> +
> +#define XR21V141X_URM_RX_FIFO_RESET	0x18
> +#define XR21V141X_URM_TX_FIFO_RESET	0x1c

Did you mean to use "UMR" above? What does URM stand for otherwise?

> +
> +#define UART_ENABLE_TX			0x1
> +#define UART_ENABLE_RX			0x2
> +
> +#define UART_MODE_RI			BIT(0)
> +#define UART_MODE_CD			BIT(1)
> +#define UART_MODE_DSR			BIT(2)
> +#define UART_MODE_DTR			BIT(3)
> +#define UART_MODE_CTS			BIT(4)
> +#define UART_MODE_RTS			BIT(5)
> +
> +#define UART_BREAK_ON			0xff
> +#define UART_BREAK_OFF			0
> +
> +#define UART_DATA_MASK			GENMASK(3, 0)
> +#define UART_DATA_7			0x7
> +#define UART_DATA_8			0x8
> +
> +#define UART_PARITY_MASK		GENMASK(6, 4)
> +#define UART_PARITY_SHIFT		0x4
> +#define UART_PARITY_NONE		0x0
> +#define UART_PARITY_ODD			0x1
> +#define UART_PARITY_EVEN		0x2
> +#define UART_PARITY_MARK		0x3
> +#define UART_PARITY_SPACE		0x4
> +
> +#define UART_STOP_MASK			BIT(7)
> +#define UART_STOP_SHIFT			0x7
> +#define UART_STOP_1			0x0
> +#define UART_STOP_2			0x1
> +
> +#define UART_FLOW_MODE_NONE		0x0
> +#define UART_FLOW_MODE_HW		0x1
> +#define UART_FLOW_MODE_SW		0x2
> +
> +#define UART_MODE_GPIO			0x0
> +#define UART_MODE_RTS_CTS		0x1
> +#define UART_MODE_DTR_DSR		0x2
> +#define UART_MODE_RS485			0x3
> +#define UART_MODE_RS485_ADDR		0x4
> +
> +static const struct xr_uart_regs xr21v141x_regs = {
> +	.enable = 0x03,
> +	.format = 0x0b,
> +	.flow_ctrl = 0x0c,
> +	.xon_char = 0x10,
> +	.xoff_char = 0x11,
> +	.loopback = 0x12,
> +	.tx_break = 0x14,
> +	.rs485_delay = 0x15,
> +	.gpio_mode = 0x1a,
> +	.gpio_dir = 0x1b,
> +	.gpio_int_mask = 0x1c,
> +	.gpio_set = 0x1d,
> +	.gpio_clr = 0x1e,
> +	.gpio_status = 0x1f,
> +};

Do you expect there to be more models supported by this driver? Perhaps
you shouldn't add this abstraction until then.

> +static int xr_set_reg(struct usb_serial_port *port, u8 block, u8 reg,
> +		      u8 val)
> +{
> +	struct usb_serial *serial = port->serial;
> +	int ret = -EINVAL;

Pointless init.

> +
> +	/* XR21V141X uses custom command for writing UART registers */

I'd drop this comment. These control messages are also used to access
the EEPROM etc.

> +	ret = usb_control_msg(serial->dev,
> +			      usb_sndctrlpipe(serial->dev, 0),
> +			      XR_SET_XR21V141X,
> +			      USB_DIR_OUT | USB_TYPE_VENDOR, val,
> +			      reg | (block << 8), NULL, 0,
> +			      USB_CTRL_SET_TIMEOUT);
> +

Remove this newline.

> +	if (ret < 0)
> +		dev_err(&port->dev, "Failed to set reg 0x%x status: %d\n",

%02x; and skip "status" like:

	dev_err(&port->dev, "failed to set reg 0x%02x: %d\n",

> +			reg, ret);
> +
> +	return ret;

As Greg suggested, please return 0 explicitly here on success.

> +}
> +
> +static int xr_get_reg(struct usb_serial_port *port, u8 block, u8 reg,
> +		      u8 *val)
> +{
> +	struct usb_serial *serial = port->serial;
> +	void *dmabuf;
> +	int ret = -EINVAL;

Unnecessary, again.

> +
> +	dmabuf = kmalloc(1, GFP_KERNEL);
> +	if (!dmabuf)
> +		return -ENOMEM;
> +
> +	/* XR21V141X uses custom command for reading UART registers */

Drop this.

> +	ret = usb_control_msg(serial->dev,
> +			      usb_rcvctrlpipe(serial->dev, 0),
> +			      XR_GET_XR21V141X,
> +			      USB_DIR_IN | USB_TYPE_VENDOR, 0,
> +			      reg | (block << 8), dmabuf, 1,
> +			      USB_CTRL_SET_TIMEOUT);

s/SET/GET/

> +

No newline.

> +	if (ret == 1) {
> +		memcpy(val, dmabuf, 1);

Use u8 and assignment here as Greg suggested.

> +		ret = 0;
> +	} else {
> +		dev_err(&port->dev, "Failed to get reg 0x%x status: %d\n",

As above.

> +			reg, ret);
> +		if (ret >= 0)
> +			ret = -EIO;
> +	}
> +
> +	kfree(dmabuf);
> +
> +	return ret;
> +}
> +
> +/* Tx and Rx clock mask values obtained from section 3.3.4 of datasheet */
> +static const struct xr_txrx_clk_mask xr21v141x_txrx_clk_masks[] = {
> +	{ 0x000, 0x000, 0x000 },
> +	{ 0x000, 0x000, 0x000 },
> +	{ 0x100, 0x000, 0x100 },
> +	{ 0x020, 0x400, 0x020 },
> +	{ 0x010, 0x100, 0x010 },
> +	{ 0x208, 0x040, 0x208 },
> +	{ 0x104, 0x820, 0x108 },
> +	{ 0x844, 0x210, 0x884 },
> +	{ 0x444, 0x110, 0x444 },
> +	{ 0x122, 0x888, 0x224 },
> +	{ 0x912, 0x448, 0x924 },
> +	{ 0x492, 0x248, 0x492 },
> +	{ 0x252, 0x928, 0x292 },
> +	{ 0x94a, 0x4a4, 0xa52 },
> +	{ 0x52a, 0xaa4, 0x54a },
> +	{ 0xaaa, 0x954, 0x4aa },
> +	{ 0xaaa, 0x554, 0xaaa },
> +	{ 0x555, 0xad4, 0x5aa },
> +	{ 0xb55, 0xab4, 0x55a },
> +	{ 0x6b5, 0x5ac, 0xb56 },
> +	{ 0x5b5, 0xd6c, 0x6d6 },
> +	{ 0xb6d, 0xb6a, 0xdb6 },
> +	{ 0x76d, 0x6da, 0xbb6 },
> +	{ 0xedd, 0xdda, 0x76e },
> +	{ 0xddd, 0xbba, 0xeee },
> +	{ 0x7bb, 0xf7a, 0xdde },
> +	{ 0xf7b, 0xef6, 0x7de },
> +	{ 0xdf7, 0xbf6, 0xf7e },
> +	{ 0x7f7, 0xfee, 0xefe },
> +	{ 0xfdf, 0xfbe, 0x7fe },
> +	{ 0xf7f, 0xefe, 0xffe },
> +	{ 0xfff, 0xffe, 0xffd },
> +};
> +
> +static int xr_set_baudrate(struct tty_struct *tty,
> +			   struct usb_serial_port *port)
> +{
> +	u32 divisor = XR_INT_OSC_HZ / tty->termios.c_ospeed;

Boom -- division by zero. B0 should drop DTR/RTS.

> +	u32 idx = (32 * divisor) & 0x1f;
> +	u16 tx_mask = xr21v141x_txrx_clk_masks[idx].tx;
> +	u16 rx_mask = (divisor & 1) ? xr21v141x_txrx_clk_masks[idx].rx1 :
> +				      xr21v141x_txrx_clk_masks[idx].rx0;

Don't do non-trivial initialisations like this as part of declaration.
Avoid the ternary operator.

> +	int ret;
> +
> +	dev_dbg(&port->dev, "Setting baud rate :%u\n", tty->termios.c_ospeed);

Space after ':', not before.

> +
> +	/*
> +	 * XR21V141X uses fractional baud rate generator with 48MHz internal
> +	 * oscillator and 19-bit programmable divisor. So theoretically it can
> +	 * generate most commonly used baud rates with high accuracy.
> +	 */
> +	ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 XR21V141X_CLOCK_DIVISOR_0, (divisor & 0xff));
> +	if (ret)
> +		return ret;
> +
> +	ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 XR21V141X_CLOCK_DIVISOR_1, ((divisor >>  8) & 0xff));
> +	if (ret)
> +		return ret;
> +
> +	ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 XR21V141X_CLOCK_DIVISOR_2, ((divisor >> 16) & 0xff));
> +	if (ret)
> +		return ret;
> +
> +	ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 XR21V141X_TX_CLOCK_MASK_0, (tx_mask & 0xff));
> +	if (ret)
> +		return ret;
> +
> +	ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 XR21V141X_TX_CLOCK_MASK_1, ((tx_mask >>  8) & 0xff));
> +	if (ret)
> +		return ret;
> +
> +	ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 XR21V141X_RX_CLOCK_MASK_0, (rx_mask & 0xff));
> +	if (ret)
> +		return ret;
> +
> +	ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 XR21V141X_RX_CLOCK_MASK_1, ((rx_mask >>  8) & 0xff));
> +
> +	return ret;
> +}
> +
> +/*
> + * According to datasheet, below is the recommended sequence for enabling UART
> + * module in XR21V141X:
> + *
> + * Enable Tx FIFO
> + * Enable Tx and Rx
> + * Enable Rx FIFO
> + */
> +static int xr_uart_enable(struct usb_serial_port *port)
> +{
> +	struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> +	int ret;
> +
> +	ret = xr_set_reg(port, XR21V141X_URM_REG_BLOCK,
> +			 XR21V141X_URM_FIFO_ENABLE_REG,
> +			 XR21V141X_URM_ENABLE_TX_FIFO);
> +	if (ret)
> +		return ret;
> +
> +	ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 port_priv->regs->enable,
> +			 UART_ENABLE_TX | UART_ENABLE_RX);
> +	if (ret)
> +		return ret;
> +
> +	ret = xr_set_reg(port, XR21V141X_URM_REG_BLOCK,
> +			 XR21V141X_URM_FIFO_ENABLE_REG,
> +			 XR21V141X_URM_ENABLE_TX_FIFO |
> +			 XR21V141X_URM_ENABLE_RX_FIFO);

Should you be undoing these on errors?

> +
> +	return ret;
> +}
> +
> +static int xr_uart_disable(struct usb_serial_port *port)
> +{
> +	struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> +	int ret;
> +
> +	ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 port_priv->regs->enable, 0);
> +	if (ret)
> +		return ret;
> +
> +	ret = xr_set_reg(port, XR21V141X_URM_REG_BLOCK,
> +			 XR21V141X_URM_FIFO_ENABLE_REG, 0);
> +
> +	return ret;
> +}
> +
> +static int xr_open(struct tty_struct *tty, struct usb_serial_port *port)
> +{
> +	int ret;
> +
> +	ret = xr_uart_enable(port);
> +	if (ret) {
> +		dev_err(&port->dev, "Failed to enable UART\n");
> +		return ret;
> +	}
> +
> +	ret = xr_set_baudrate(tty, port);

tty will be NULL when called by the console driver.

Why only init the line speed? Driver typically call set_termios() here
when not used as a console.

> +	if (ret) {
> +		dev_err(&port->dev, "Failed to set baudrate\n");
> +		return ret;
> +	}
> +
> +	return usb_serial_generic_open(tty, port);

Disable on errors?

> +}
> +
> +static void xr_close(struct usb_serial_port *port)
> +{
> +	usb_serial_generic_close(port);
> +
> +	xr_uart_disable(port);
> +}
> +
> +static void xr_set_flow_mode(struct tty_struct *tty,
> +			     struct usb_serial_port *port,
> +			     unsigned int cflag)
> +{
> +	struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> +	u8 flow, gpio_mode;
> +	int ret;
> +
> +	ret = xr_get_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 port_priv->regs->gpio_mode, &gpio_mode);
> +	if (ret)
> +		return;
> +
> +	if (cflag & CRTSCTS) {
> +		dev_dbg(&port->dev, "Enabling hardware flow ctrl\n");
> +		flow = UART_FLOW_MODE_HW;
> +		gpio_mode |= UART_MODE_RTS_CTS;

These modes are exclusive, you cannot use |= here.

> +	} else if (I_IXOFF(tty) || I_IXON(tty)) {

This should just be IXOFF(tty) (flow control on input).

> +		u8 start_char = START_CHAR(tty);
> +		u8 stop_char = STOP_CHAR(tty);
> +
> +		dev_dbg(&port->dev, "Enabling sw flow ctrl\n");
> +		flow = UART_FLOW_MODE_SW;
> +		gpio_mode |= UART_MODE_GPIO;

Same here, this is broken; ORing with 0 doesn't set mode 0.

> +
> +		xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			   port_priv->regs->xon_char, start_char);
> +		xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			   port_priv->regs->xoff_char, stop_char);
> +	} else {
> +		dev_dbg(&port->dev, "No flow ctrl\n");
> +		flow = UART_FLOW_MODE_NONE;

I assume you need to set UART_MODE_GPIO here too to be able to control
RTS manually (default mode is RTS/CTS flow control).

> +	}
> +
> +	ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 port_priv->regs->flow_ctrl, flow);
> +	if (ret)
> +		return;

The datasheet says that the flow control register can only be updated
when the uart is disabled.

	"These registers should only be written to when the UART is
	 disabled. Writing to the FLOW_CONTROL register when the UART is
	 enabled will result in undefined behavior."

> +
> +	xr_set_reg(port, XR21V141X_UART_REG_BLOCK, port_priv->regs->gpio_mode,
> +		   gpio_mode);
> +}
> +
> +static void xr_set_termios(struct tty_struct *tty,
> +			   struct usb_serial_port *port,
> +			   struct ktermios *old_termios)
> +{
> +	struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> +	struct device *dev = &port->dev;
> +	unsigned int cflag, old_cflag;
> +	int ret;
> +	u8 bits;
> +
> +	cflag = tty->termios.c_cflag;
> +	old_cflag = old_termios->c_cflag;
> +
> +	if (tty->termios.c_ospeed != old_termios->c_ospeed)
> +		xr_set_baudrate(tty, port);
> +
> +	ret = xr_get_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 port_priv->regs->format, &bits);
> +	if (ret)
> +		return;

No need to retrieve the current settings.

> +
> +	/* If the number of data bits is to be updated */
> +	if ((cflag & CSIZE) != (old_cflag & CSIZE)) {

Use C_CSIZE(tty) and friends and set these unconditionally.

> +		bits &= ~UART_DATA_MASK;
> +		switch (cflag & CSIZE) {
> +		case CS7:
> +			bits |= UART_DATA_7;
> +			dev_dbg(dev, "Setting data bits: 7\n");
> +			break;
> +		case CS8:
> +		/* CS9 not supported */
> +		default:
> +			bits |= UART_DATA_8;
> +			dev_dbg(dev, "Setting data bits: 8\n");

You should report back that you cannot set CS5 and CS6 by restoring the
old setting in tty->termios.

> +			break;
> +		}
> +	}
> +
> +	if ((cflag & (PARENB | PARODD | CMSPAR)) !=
> +	    (old_cflag & (PARENB | PARODD | CMSPAR))) {

As above, determine these bits unconditionally.

> +		bits &= ~UART_PARITY_MASK;
> +		if (cflag & PARENB) {
> +			if (cflag & CMSPAR) {
> +				if (cflag & PARODD) {
> +					bits |= (UART_PARITY_MARK <<
> +						 UART_PARITY_SHIFT);

Parenthesis not need. Hopefully cleaner when you have reduced
indentation.

> +					dev_dbg(dev, "Setting parity: MARK\n");
> +				} else {
> +					bits |= (UART_PARITY_SPACE <<
> +						 UART_PARITY_SHIFT);
> +					dev_dbg(dev, "Setting parity: SPACE\n");
> +				}
> +			} else {
> +				if (cflag & PARODD) {
> +					bits |= (UART_PARITY_ODD <<
> +						 UART_PARITY_SHIFT);
> +					dev_dbg(dev, "Setting parity: ODD\n");
> +				} else {
> +					bits |= (UART_PARITY_EVEN <<
> +						 UART_PARITY_SHIFT);
> +					dev_dbg(dev, "Setting parity: EVEN\n");

And please drop all these dev_dbg (also for data bits).

> +				}
> +			}
> +		}
> +	}
> +
> +	if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) {
> +		bits &= ~UART_STOP_MASK;
> +		if (cflag & CSTOPB) {
> +			bits |= (UART_STOP_2 << UART_STOP_SHIFT);
> +			dev_dbg(dev, "Setting stop bits: 2\n");
> +		} else {
> +			bits |= (UART_STOP_1 << UART_STOP_SHIFT);
> +			dev_dbg(dev, "Setting stop bits: 1\n");
> +		}
> +	}

As above.

> +
> +	ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 port_priv->regs->format, (bits & 0xff));

bits is u8, no need to mask

> +	if (ret)
> +		return;
> +
> +	xr_set_flow_mode(tty, port, cflag);

cflag can be retreived from tty.

> +}
> +
> +static int xr_tiocmset_port(struct usb_serial_port *port,
> +			    unsigned int set, unsigned int clear)
> +{
> +	struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> +	int ret = 0;
> +	u8 gpio_set = 0;
> +	u8 gpio_clr = 0;
> +
> +	/* Modem control pins are active low, so set & clr are swapped */
> +	if (set & TIOCM_RTS)
> +		gpio_clr |= UART_MODE_RTS;
> +	if (set & TIOCM_DTR)
> +		gpio_clr |= UART_MODE_DTR;
> +	if (clear & TIOCM_RTS)
> +		gpio_set |= UART_MODE_RTS;
> +	if (clear & TIOCM_DTR)
> +		gpio_set |= UART_MODE_DTR;
> +
> +	/* Writing '0' to gpio_{set/clr} bits has no effect, so no need to do */
> +	if (gpio_clr)
> +		ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +				 port_priv->regs->gpio_clr, gpio_clr);

Please add brackets since you have a multiline statement here.

> +
> +	if (gpio_set)
> +		ret = xr_set_reg(port, XR21V141X_UART_REG_BLOCK,
> +				 port_priv->regs->gpio_set, gpio_set);

Same here.

> +
> +	return ret;
> +}
> +
> +static int xr_tiocmset(struct tty_struct *tty,
> +		       unsigned int set, unsigned int clear)
> +{
> +	struct usb_serial_port *port = tty->driver_data;
> +
> +	return xr_tiocmset_port(port, set, clear);
> +}
> +
> +static void xr_dtr_rts(struct usb_serial_port *port, int on)
> +{
> +	if (on)
> +		xr_tiocmset_port(port, TIOCM_DTR | TIOCM_RTS, 0);
> +	else
> +		xr_tiocmset_port(port, 0, TIOCM_DTR | TIOCM_RTS);
> +}
> +
> +static int xr_tiocmget(struct tty_struct *tty)
> +{
> +	struct usb_serial_port *port = tty->driver_data;
> +	struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> +	int ret;
> +	u8 status;
> +
> +	ret = xr_get_reg(port, XR21V141X_UART_REG_BLOCK,
> +			 port_priv->regs->gpio_status, &status);
> +	if (ret)
> +		return ret;
> +
> +	/*
> +	 * Modem control pins are active low, so reading '0' means it is active
> +	 * and '1' means not active.
> +	 */
> +	ret = ((status & UART_MODE_DTR) ? 0 : TIOCM_DTR) |
> +	      ((status & UART_MODE_RTS) ? 0 : TIOCM_RTS) |
> +	      ((status & UART_MODE_CTS) ? 0 : TIOCM_CTS) |
> +	      ((status & UART_MODE_DSR) ? 0 : TIOCM_DSR) |
> +	      ((status & UART_MODE_RI) ? 0 : TIOCM_RI) |
> +	      ((status & UART_MODE_CD) ? 0 : TIOCM_CD);

Can you read back also the outputs? Also in automatic mode?

> +
> +	return ret;
> +}
> +
> +static void xr_break_ctl(struct tty_struct *tty, int break_state)
> +{
> +	struct usb_serial_port *port = tty->driver_data;
> +	struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> +	u8 state;
> +
> +	if (break_state == 0)
> +		state = UART_BREAK_OFF;
> +	else
> +		state = UART_BREAK_ON;
> +
> +	dev_dbg(&port->dev, "Turning break %s\n",
> +		state == UART_BREAK_OFF ? "off" : "on");
> +	xr_set_reg(port, XR21V141X_UART_REG_BLOCK, port_priv->regs->tx_break,
> +		   state);
> +}
> +
> +static int xr_port_probe(struct usb_serial_port *port)
> +{
> +	struct xr_port_private *port_priv;
> +
> +	port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL);
> +	if (!port_priv)
> +		return -ENOMEM;
> +
> +	/* XR21V141X specific settings */
> +	port_priv->regs = &xr21v141x_regs;

May not be needed.

> +
> +	usb_set_serial_port_data(port, port_priv);
> +
> +	return 0;
> +}
> +
> +static int xr_port_remove(struct usb_serial_port *port)
> +{
> +	struct xr_port_private *port_priv = usb_get_serial_port_data(port);
> +
> +	kfree(port_priv);
> +
> +	return 0;
> +}
> +
> +static const struct usb_device_id id_table[] = {
> +	{ USB_DEVICE(0x04e2, 0x1410) }, /* XR21V141X */
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(usb, id_table);
> +
> +static struct usb_serial_driver xr_device = {
> +	.driver = {
> +		.owner = THIS_MODULE,
> +		.name =	"xr_serial",
> +	},
> +	.id_table		= id_table,
> +	.num_ports		= 1,
> +	.bulk_in_size		= 384,
> +	.bulk_out_size		= 128,

You should not necessarily set these to match the hardware fifo sizes.
They default to the respective endpoint size, but may be increased for
improved throughput.

> +	.open			= xr_open,
> +	.close			= xr_close,
> +	.break_ctl		= xr_break_ctl,
> +	.set_termios		= xr_set_termios,
> +	.tiocmget		= xr_tiocmget,
> +	.tiocmset		= xr_tiocmset,
> +	.port_probe		= xr_port_probe,
> +	.port_remove		= xr_port_remove,
> +	.dtr_rts		= xr_dtr_rts
> +};

As I mentioned elsewhere, you should only register a tty device for the
data interface, but still claim the control interface.

You probably should reject the control interface and claim it when
probing the data interface (rather than return 1 from attach as I
mentioned earlier).

> +
> +static struct usb_serial_driver * const serial_drivers[] = {
> +	&xr_device, NULL
> +};
> +
> +module_usb_serial_driver(serial_drivers, id_table);
> +
> +MODULE_AUTHOR("Manivannan Sadhasivam <mani@kernel.org>");
> +MODULE_DESCRIPTION("MaxLinear/Exar USB to Serial driver");
> +MODULE_LICENSE("GPL");

Generally nice and clean overall.

Johan