Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
Date:   Thu, 3 Sep 2020 09:23:00 -0700
From:   Matthias Kaehlcke <mka@chromium.org>
To:     satya priya <skakit@codeaurora.org>
Cc:     Bjorn Andersson <bjorn.andersson@linaro.org>,
        gregkh@linuxfoundation.org, Andy Gross <agross@kernel.org>,
        Rob Herring <robh+dt@kernel.org>,
        linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
        linux-kernel@vger.kernel.org, akashast@codeaurora.org,
        rojay@codeaurora.org, msavaliy@qti.qualcomm.com
Subject: Re: [PATCH V4 3/4] arm64: dts: qcom: sc7180: Add sleep state for BT
 UART
Message-ID: <20200903162300.GJ3419728@google.com>
References: <1599145498-20707-1-git-send-email-skakit@codeaurora.org>
 <1599145498-20707-4-git-send-email-skakit@codeaurora.org>
MIME-Version: 1.0
Content-Type: text/plain; charset=utf-8
Content-Disposition: inline
In-Reply-To: <1599145498-20707-4-git-send-email-skakit@codeaurora.org>
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

On Thu, Sep 03, 2020 at 08:34:57PM +0530, satya priya wrote:
> Add sleep state for BT uart to support the wakeup feature.
> 
> Signed-off-by: satya priya <skakit@codeaurora.org>
> Reviewed-by: Akash Asthana <akashast@codeaurora.org>
> ---
> Changes in V2:
>  - This patch adds sleep state for BT UART. Newly added in V2.
> 
> Changes in V3:
>  - Remove "output-high" for TX from both sleep and default states
>    as it is not required. Configure pull-up for TX in sleep state.
> 
> Changes in V4:
>  - As per Matthias's comment, removed drive-strength for sleep state
>    and fixed nit-pick.
> 
>  arch/arm64/boot/dts/qcom/sc7180-idp.dts | 37 +++++++++++++++++++++++++++++++++
>  1 file changed, 37 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index cecac3e..77e3523 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -507,6 +507,43 @@
>  	};
>  };
>  
> +&qup_uart3_sleep {
> +	pinconf-cts {
> +		/*
> +		 * Configure no-pull on CTS. As this is driven by BT, do not
> +		 * specify any pull in order to not conflict with BT pulls.
> +		 */
> +		pins = "gpio38";
> +		bias-disable;
> +	};
> +
> +	pinconf-rts {
> +		/*
> +		 * Configure pull-down on RTS to make sure that the BT SoC can
> +		 * wake up the system by sending wakeup bytes during suspend.
> +		 */
> +		pins = "gpio39";
> +		bias-pull-down;
> +	};
> +
> +	pinconf-tx {
> +		/* Configure pull-up on TX when it isn't actively driven */
> +		pins = "gpio40";
> +		bias-pull-up;
> +	};
> +
> +	pinconf-rx {
> +		/*
> +		 * Configure a pull-up on RX. This is needed to avoid
> +		 * garbage data when the TX pin of the Bluetooth module is
> +		 * in tri-state (module powered off or not driving the
> +		 * signal yet).
> +		 */
> +		pins = "gpio41";
> +		bias-pull-up;
> +	};
> +};
> +
>  &qup_uart8_default {
>  	pinconf-tx {
>  		pins = "gpio44";

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>