Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
Date:   Fri, 11 Sep 2020 08:52:32 -0500
From:   Bjorn Andersson <bjorn.andersson@linaro.org>
To:     skakit@codeaurora.org
Cc:     Doug Anderson <dianders@chromium.org>,
        Matthias Kaehlcke <mka@chromium.org>,
        Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
        Andy Gross <agross@kernel.org>,
        Rob Herring <robh+dt@kernel.org>,
        linux-arm-msm <linux-arm-msm@vger.kernel.org>,
        "open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS" 
        <devicetree@vger.kernel.org>, LKML <linux-kernel@vger.kernel.org>,
        Akash Asthana <akashast@codeaurora.org>,
        Roja Rani Yarubandi <rojay@codeaurora.org>,
        msavaliy@qti.qualcomm.com
Subject: Re: [PATCH V5 2/4] arm64: dts: qcom: sc7180: Add necessary pinctrl
 and interrupt config for BT UART
Message-ID: <20200911135232.GY3715@yoga>
References: <1599742438-16811-1-git-send-email-skakit@codeaurora.org>
 <1599742438-16811-3-git-send-email-skakit@codeaurora.org>
 <CAD=FV=ULJqgHutr524wb-wVq4gejqo1p_zqRXP=h4Co6Gvmzew@mail.gmail.com>
 <010101747ca94cce-42d129fa-0374-4f12-aab8-2ccafd02b3c7-000000@us-west-2.amazonses.com>
MIME-Version: 1.0
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
In-Reply-To: <010101747ca94cce-42d129fa-0374-4f12-aab8-2ccafd02b3c7-000000@us-west-2.amazonses.com>
Sender: linux-kernel-owner@vger.kernel.org
Precedence: bulk

On Fri 11 Sep 05:15 CDT 2020, skakit@codeaurora.org wrote:

> On 2020-09-10 20:10, Doug Anderson wrote:
> > Hi,
> > 
> > On Thu, Sep 10, 2020 at 5:55 AM satya priya <skakit@codeaurora.org>
> > wrote:
> > > 
> > > Add a suitable sleep configuration for uart3 to support Bluetooth
> > > wakeup.
> > > 
> > > If QUP function is selected in sleep state, UART RTS/RFR is pulled
> > > high
> > > during suspend and BT SoC not able to send wakeup bytes. So, configure
> > > GPIO mode in sleep state to keep it low during suspend.
> > > 
> > > Signed-off-by: satya priya <skakit@codeaurora.org>
> > > Reviewed-by: Akash Asthana <akashast@codeaurora.org>
> > > ---
> > > Changes in V2:
> > >  - This patch adds sleep state for BT UART. Newly added in V2.
> > > 
> > > Changes in V3:
> > >  - Remove "output-high" for TX from both sleep and default states
> > >    as it is not required. Configure pull-up for TX in sleep state.
> > > 
> > > Changes in V4:
> > >  - As per Matthias's comment, removed drive-strength for sleep state
> > >    and fixed nit-pick.
> > > 
> > > Changes in V5:
> > >  - As per Matthias's comments, moved pinmux change for sleep state,
> > >    pinctrl and interrupt config to the board specific file.
> > > 
> > >  arch/arm64/boot/dts/qcom/sc7180-idp.dts | 48
> > > +++++++++++++++++++++++++++++++++
> > >  1 file changed, 48 insertions(+)
> > 
> > Similar comment to patch #1 in that this applies only to the IDP board
> > but that's not obvious from ${SUBJECT}
> > 
> 
> Okay.
> 
> > 
> > > diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > index 04888df..e529a41 100644
> > > --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> > > @@ -344,6 +344,10 @@
> > >  };
> > > 
> > >  &uart3 {
> > > +       pinctrl-names = "default", "sleep";
> > > +       pinctrl-1 = <&qup_uart3_sleep>;
> > > +       interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
> > > +                               <&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
> > 
> > You need a:
> > 
> > /delete-property/interrupts;
> > 
> > ...or, alternatively, a patch before this one that converts all the
> > UARTs in sc7180 to just use interrupts-extended.
> > 
> 
> Sure, I will add this. But I think when both are added,
> "interrupts-extended" will get priority as per [1] and there wouldn't be any
> problem.
> 

You're indeed correct, please stick with what you have.

Regards,
Bjorn

> [1] https://www.kernel.org/doc/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> 
> > 
> > >         status = "okay";
> > 
> > Slight nit is that usually I see the status line first.  All the other
> > instances in this file have it that way.  Can you match?
> > 
> 
> Ok, will correct it.
> 
> > 
> > 
> > 
> > -Doug