Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
Date:   Mon, 16 Nov 2020 11:03:02 +0100
From:   Jacopo Mondi <jacopo@jmondi.org>
To:     Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc:     Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>,
        Jacopo Mondi <jacopo+renesas@jmondi.org>,
        laurent.pinchart+renesas@ideasonboard.com,
        niklas.soderlund+renesas@ragnatech.se, geert@linux-m68k.org,
        linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org,
        linux-kernel@vger.kernel.org, Hyun Kwon <hyunk@xilinx.com>,
        Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Subject: Re: [PATCH v4 1/8] media: i2c: Add driver for RDACM21 camera module
Message-ID: <20201116100302.mmv5skzk7s34ocxa@uno.localdomain>
References: <20201112162729.101384-1-jacopo+renesas@jmondi.org>
 <20201112162729.101384-2-jacopo+renesas@jmondi.org>
 <95e2e968-d77f-0838-641a-d81a6df6f0b5@ideasonboard.com>
 <20201114140457.h7x6l53cfqqhpq6l@uno.localdomain>
 <20201116090833.GB6540@pendragon.ideasonboard.com>
MIME-Version: 1.0
Content-Type: text/plain; charset=utf-8
Content-Disposition: inline
Content-Transfer-Encoding: 8bit
In-Reply-To: <20201116090833.GB6540@pendragon.ideasonboard.com>
Precedence: bulk

Hi Laurent,

On Mon, Nov 16, 2020 at 11:08:33AM +0200, Laurent Pinchart wrote:
> Hi Jacopo,
>
> On Sat, Nov 14, 2020 at 03:04:57PM +0100, Jacopo Mondi wrote:
> > On Thu, Nov 12, 2020 at 10:31:05PM +0000, Kieran Bingham wrote:
> > > Hi Jacopo,
> >
> > [snip]
> >
> > > > +	/* Wait for firmware boot by reading streamon status. */
> > > > +	ov490_write(dev, 0xfffd, 0x80);
> > > > +	ov490_write(dev, 0xfffe, 0x29);
> > > > +	usleep_range(100, 150);
> > > > +	for (timeout = 300; timeout > 0; timeout--) {
> > > > +		ov490_read(dev, 0xd000, &val);
> > > > +		if (val == 0x0c)
> > >
> > > What is 0x0c here? Is it something we can better describe in a #define?
> > >
> >
> > The 0x0c value itself means "frame output enable" + "whole frame
> > output enable". I don't think it has much value to define it,
> > otherwise we would need to define also the register 8029d000
>
> Shouldn't we have macros for *all* register addresses and fields ?
>

I'm not sure it's worth it, we have a single register-value table, and
the way ov490 is programmed, as you can see is to specify the high
bytes of the 32-bits register to write in the special 'page' registers
0xfffd, 0xfffe (which I've not found documented)

	ov490_write(dev, 0xfffd, 0x80);
	ov490_write(dev, 0xfffe, 0x29);
	ov490_read(dev, 0xd000, &val);

This, to my understanding reads register 0x8029d000

We would need three macros, maybe a
        PAGE_HIGH(reg)  (u8)(reg >> 24)
        PAGE_LOW(reg)   (u8)(reg >> 16)
        REG_LOW(reg)    (u16)(reg)

To that's a lot of churn for no gain imho, the code isn't much more
clear


> > Also, the ov490 is programmed loading the content of a SPI Flash chip,
> > I guess it's just known that "output enabled" is required to have
> > stream operations properly working.
> >
> > > > +			break;
> > > > +		mdelay(1);
> > > > +	}
> > > > +	if (!timeout) {
> > > > +		dev_err(dev->dev, "Timeout firmware boot wait\n");
> > > > +		return -ENODEV;
> > > > +	}
> > > > +	dev_dbg(dev->dev, "Firmware booted in %u msec\n", 300 - timeout);
> > > > +
> > > > +	/* Read OV10640 Id to test communications. */
> > > > +	ov490_write(dev, 0xfffd, 0x80);
> > > > +	ov490_write(dev, 0xfffe, 0x19);
> > > > +	usleep_range(100, 150);

Not to add that I don't have register 0x80195000 in the documentation I've
access to (the master SCCB control page is at  address 0x8090xxxx

> > > > +
> > > > +	ov490_write(dev, 0x5000, 0x01);
> > > > +	ov490_write(dev, 0x5001, 0x30);
> > > > +	ov490_write(dev, 0x5002, 0x0a)
> > > > +	ov490_write(dev, 0xfffe, 0x80);

This sequence in example, reads the 0x300a register of the slave
(ov10640) by programming registers
                0x80195000      0x1
                0x80195001      0x30
                0x80195002      0x0a

> > > > +	usleep_range(100, 150);
> > > > +	ov490_write(dev, 0xc0, 0xc1);

Triggering a transaction writing 0xc1 to 0x808000c0 (0xc1
undocumented)

> > > > +	ov490_write(dev, 0xfffe, 0x19);
> > > > +	usleep_range(1000, 1500);
> > > > +	ov490_read(dev, 0x5000, &val);

and reading back the transaction result at address 0x80195000

I got these parts from
https://github.com/CogentEmbedded/meta-rcar/blob/v2.12.0/meta-rcar-gen3/recipes-kernel/linux/linux-renesas/0040-H3-MAX9286-TI964-support-add-10635-10640-cameras.patch#L3732

and that's why I kept Vladimir's authorship in MODULE_AUTHORS()

> > > > +	if (val != OV10640_ID_LOW) {
> > > > +		dev_err(dev->dev, "OV10640 ID mismatch: (0x%02x)\n", val);
> > > > +		return -ENODEV;
> > > > +	}
> > > > +
> > > > +	dev_dbg(dev->dev, "OV10640 ID = 0x%2x\n", val);
> > > > +
> > > > +	for (i = 0; i < ARRAY_SIZE(ov490_regs_wizard); ++i) {
> > > > +		ret = ov490_write(dev, ov490_regs_wizard[i].reg,
> > > > +				  ov490_regs_wizard[i].val);
> > > > +		if (ret < 0) {
> > > > +			dev_err(dev->dev,
> > > > +				"%s: register %u (0x%04x) write failed (%d)\n",
> > > > +				__func__, i, ov490_regs_wizard[i].reg, ret);
> > > > +
> > > > +			return -EIO;
> > > > +		}
> > > > +
> > > > +		usleep_range(100, 150);
> > > > +	}
> > > > +
> > > > +	/*
> > > > +	 * The ISP is programmed with the content of a serial flash memory.
> > > > +	 * Read the firmware configuration to reflect it through the V4L2 APIs.
> > > > +	 */
> > > > +	ov490_write(dev, 0xfffd, 0x80);
> > > > +	ov490_write(dev, 0xfffe, 0x82);
> > > > +	usleep_range(100, 150);
> > > > +	ov490_read(dev, OV490_ISP_HSIZE_HIGH, &val);
> > > > +	dev->fmt.width = (val & 0xf) << 8;
> > > > +	ov490_read(dev, OV490_ISP_HSIZE_LOW, &val);
> > > > +	dev->fmt.width |= (val & 0xff);
> > > > +
> > > > +	ov490_read(dev, OV490_ISP_VSIZE_HIGH, &val);
> > > > +	dev->fmt.height = (val & 0xf) << 8;
> > > > +	ov490_read(dev, OV490_ISP_VSIZE_LOW, &val);
> > > > +	dev->fmt.height |= val & 0xff;
> > > > +
> > > > +	/* Set bus width to 12 bits [0:11] */
> > > > +	ov490_write(dev, 0xfffd, 0x80);
> > > > +	ov490_write(dev, 0xfffe, 0x28);
> > > > +	usleep_range(100, 150);
> > > > +	ov490_write(dev, 0x6009, 0x10);
> > > > +
> > > > +	dev_info(dev->dev, "Identified RDACM21 camera module\n");
> > > > +
> > > > +	return 0;
> > > > +}
> > > > +
> > > > +static int rdacm21_initialize(struct rdacm21_device *dev)
> > > > +{
> > > > +	int ret;
> > > > +
> > > > +	/* Verify communication with the MAX9271: ping to wakeup. */
> > > > +	dev->serializer->client->addr = MAX9271_DEFAULT_ADDR;
> > > > +	i2c_smbus_read_byte(dev->serializer->client);
> > > > +
> > > > +	/* Serial link disabled during config as it needs a valid pixel clock. */
> > > > +	ret = max9271_set_serial_link(dev->serializer, false);
> > > > +	if (ret)
> > > > +		return ret;
> > > > +
> > > > +	/* Set GPO high to hold OV490 in reset during max9271 configuration. */
> > > > +	ret = max9271_set_gpios(dev->serializer, MAX9271_GPO);
> > > > +	if (ret)
> > > > +		return ret;
> > > > +
> > > > +	/* Configure I2C bus at 105Kbps speed and configure GMSL link. */
> > > > +	ret = max9271_configure_i2c(dev->serializer,
> > > > +				    MAX9271_I2CSLVSH_469NS_234NS |
> > > > +				    MAX9271_I2CSLVTO_1024US |
> > > > +				    MAX9271_I2CMSTBT_105KBPS);
> > > > +	if (ret)
> > > > +		return ret;
> > > > +
> > > > +	ret = max9271_configure_gmsl_link(dev->serializer);
> > > > +	if (ret)
> > > > +		return ret;
> > > > +
> > > > +	ret = max9271_set_address(dev->serializer, dev->addrs[0]);
> > > > +	if (ret)
> > > > +		return ret;
> > > > +	dev->serializer->client->addr = dev->addrs[0];
> > > > +
> > > > +	/*
> > > > +	 * Release OV490 from reset and program address translation
> > > > +	 * before performing OV490 configuration.
> > > > +	 */
> > > > +	ret = max9271_clear_gpios(dev->serializer, MAX9271_GPO);
> > > > +	if (ret)
> > > > +		return ret;
> > > > +
> > > > +	ret = max9271_set_translation(dev->serializer, dev->addrs[1],
> > > > +				      OV490_I2C_ADDRESS);
> > > > +	if (ret)
> > > > +		return ret;
> > > > +	dev->isp->addr = dev->addrs[1];
> > > > +
> > > > +	ret = ov490_initialize(dev);
> > > > +	if (ret)
> > > > +		return ret;
> > > > +
> > > > +	/*
> > > > +	 * Set reverse channel high threshold to increase noise immunity.
> > > > +	 *
> > > > +	 * This should be compensated by increasing the reverse channel
> > > > +	 * amplitude on the remote deserializer side.
> > > > +	 */
> > > > +	ret = max9271_set_high_threshold(dev->serializer, true);
> > > > +	if (ret)
> > > > +		return ret;
> > > > +
> > > > +	return 0;
> > > > +}
> > > > +
> > > > +static int rdacm21_probe(struct i2c_client *client)
> > > > +{
> > > > +	struct rdacm21_device *dev;
> > > > +	struct fwnode_handle *ep;
> > > > +	int ret;
> > > > +
> > > > +	dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL);
> > > > +	if (!dev)
> > > > +		return -ENOMEM;
> > > > +	dev->dev = &client->dev;
> > > > +
> > > > +	dev->serializer = devm_kzalloc(&client->dev, sizeof(*dev->serializer),
> > > > +				       GFP_KERNEL);
> > > > +	if (!dev->serializer)
> > > > +		return -ENOMEM;
> > > > +
> > > > +	dev->serializer->client = client;
> > > > +
> > > > +	ret = of_property_read_u32_array(client->dev.of_node, "reg",
> > > > +					 dev->addrs, 2);
> > > > +	if (ret < 0) {
> > > > +		dev_err(dev->dev, "Invalid DT reg property: %d\n", ret);
> > > > +		return -EINVAL;
> > > > +	}
> > > > +
> > > > +	/* Create the dummy I2C client for the sensor. */
> > > > +	dev->isp = i2c_new_dummy_device(client->adapter, OV490_I2C_ADDRESS);
> > > > +	if (IS_ERR(dev->isp))
> > > > +		return PTR_ERR(dev->isp);
> > > > +
> > > > +	ret = rdacm21_initialize(dev);
> > > > +	if (ret < 0)
> > > > +		goto error;
> > > > +
> > > > +	/* Initialize and register the subdevice. */
> > > > +	v4l2_i2c_subdev_init(&dev->sd, client, &rdacm21_subdev_ops);
> > > > +	dev->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> > > > +
> > > > +	v4l2_ctrl_handler_init(&dev->ctrls, 1);
> > > > +	v4l2_ctrl_new_std(&dev->ctrls, NULL, V4L2_CID_PIXEL_RATE,
> > > > +			  OV10640_PIXEL_RATE, OV10640_PIXEL_RATE, 1,
> > > > +			  OV10640_PIXEL_RATE);
> > > > +	dev->sd.ctrl_handler = &dev->ctrls;
> > > > +
> > > > +	ret = dev->ctrls.error;
> > > > +	if (ret)
> > > > +		goto error_free_ctrls;
> > > > +
> > > > +	dev->pad.flags = MEDIA_PAD_FL_SOURCE;
> > > > +	dev->sd.entity.flags |= MEDIA_ENT_F_CAM_SENSOR;
> > > > +	ret = media_entity_pads_init(&dev->sd.entity, 1, &dev->pad);
> > > > +	if (ret < 0)
> > > > +		goto error_free_ctrls;
> > > > +
> > > > +	ep = fwnode_graph_get_next_endpoint(dev_fwnode(&client->dev), NULL);
> > > > +	if (!ep) {
> > > > +		dev_err(&client->dev,
> > > > +			"Unable to get endpoint in node %pOF\n",
> > > > +			client->dev.of_node);
> > > > +		ret = -ENOENT;
> > > > +		goto error_free_ctrls;
> > > > +	}
> > > > +	dev->sd.fwnode = ep;
> > > > +
> > > > +	ret = v4l2_async_register_subdev(&dev->sd);
> > > > +	if (ret)
> > > > +		goto error_put_node;
> > > > +
> > > > +	return 0;
> > > > +
> > > > +error_put_node:
> > > > +	fwnode_handle_put(dev->sd.fwnode);
> > > > +error_free_ctrls:
> > > > +	v4l2_ctrl_handler_free(&dev->ctrls);
> > > > +error:
> > > > +	i2c_unregister_device(dev->isp);
> > > > +
> > > > +	return ret;
> > > > +}
> > > > +
> > > > +static int rdacm21_remove(struct i2c_client *client)
> > > > +{
> > > > +	struct rdacm21_device *dev = i2c_to_rdacm21(client);
> > > > +
> > > > +	fwnode_handle_put(dev->sd.fwnode);
> > > > +	v4l2_async_unregister_subdev(&dev->sd);
> > > > +	v4l2_ctrl_handler_free(&dev->ctrls);
> > > > +	i2c_unregister_device(dev->isp);
> > > > +
> > > > +	return 0;
> > > > +}
> > > > +
> > > > +static const struct of_device_id rdacm21_of_ids[] = {
> > > > +	{ .compatible = "imi,rdacm21" },
> > > > +	{ }
> > > > +};
> > > > +MODULE_DEVICE_TABLE(of, rdacm21_of_ids);
> > > > +
> > > > +static struct i2c_driver rdacm21_i2c_driver = {
> > > > +	.driver	= {
> > > > +		.name	= "rdacm21",
> > > > +		.of_match_table = rdacm21_of_ids,
> > > > +	},
> > > > +	.probe_new	= rdacm21_probe,
> > > > +	.remove		= rdacm21_remove,
> > > > +};
> > > > +
> > > > +module_i2c_driver(rdacm21_i2c_driver);
> > > > +
> > > > +MODULE_DESCRIPTION("GMSL Camera driver for RDACM21");
> > > > +MODULE_AUTHOR("Jacopo Mondi, Kieran Bingham, Laurent Pinchart, Niklas Söderlund, Vladimir Barinov");
> > >
> > > I think by this point you could chop MODULE_AUTHOR for this one down to
> > > just you ;-)
> > >
> > >
> > > A fairly arbitrary, and cursory
> > >
> > > Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
> > >
> > > I'll be aiming to test this (series) as soon as I can too.
> >
> > Thanks, let me know if I should submit for proper inclusion!
> >
> > > > +MODULE_LICENSE("GPL v2");
>
> --
> Regards,
>
> Laurent Pinchart