Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
Date:   Wed, 14 Apr 2021 08:59:28 +0200
From:   Marc Kleine-Budde <mkl@pengutronix.de>
To:     Aswath Govindraju <a-govindraju@ti.com>
Cc:     Vignesh Raghavendra <vigneshr@ti.com>,
        Kishon Vijay Abraham I <kishon@ti.com>,
        Lokesh Vutla <lokeshvutla@ti.com>,
        Grygorii Strashko <grygorii.strashko@ti.com>,
        Chandrasekar Ramakrishnan <rcsekar@samsung.com>,
        Wolfgang Grandegger <wg@grandegger.com>,
        "David S. Miller" <davem@davemloft.net>,
        Jakub Kicinski <kuba@kernel.org>,
        Rob Herring <robh+dt@kernel.org>,
        Vinod Koul <vkoul@kernel.org>,
        Sriram Dash <sriram.dash@samsung.com>,
        linux-can@vger.kernel.org, netdev@vger.kernel.org,
        devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
        linux-phy@lists.infradead.org
Subject: Re: [PATCH 0/4] CAN TRANSCEIVER: Add support for CAN transceivers
Message-ID: <20210414065928.d2carmtxsp57cczw@pengutronix.de>
References: <20210409134056.18740-1-a-govindraju@ti.com>
MIME-Version: 1.0
Content-Type: multipart/signed; micalg=pgp-sha512;
        protocol="application/pgp-signature"; boundary="raq3yd6i5d77bb2l"
Content-Disposition: inline
In-Reply-To: <20210409134056.18740-1-a-govindraju@ti.com>
Precedence: bulk


--raq3yd6i5d77bb2l
Content-Type: text/plain; charset=utf-8
Content-Disposition: inline
Content-Transfer-Encoding: quoted-printable

On 09.04.2021 19:10:50, Aswath Govindraju wrote:
> The following series of patches add support for CAN transceivers.
>=20
> TCAN1042 has a standby signal that needs to be pulled high for
> sending/receiving messages[1]. TCAN1043 has a enable signal along with
> standby signal that needs to be pulled up for sending/receiving
> messages[2], and other combinations of the two lines can be used to put t=
he
> transceiver in different states to reduce power consumption. On boards
> like the AM654-idk and J721e-evm these signals are controlled using gpios.
>=20
> Patch 1 models the transceiver as a phy device tree node with properties
> for max bit rate supported, gpio properties for indicating gpio pin numbe=
rs
> to which standby and enable signals are connected.

Please add a patch that adds the driver and the bindings to the
MAINTAINERS file. Feel free to add it CAN NETWORK DRIVERS.

regards,
Marc

--=20
Pengutronix e.K.                 | Marc Kleine-Budde           |
Embedded Linux                   | https://www.pengutronix.de  |
Vertretung West/Dortmund         | Phone: +49-231-2826-924     |
Amtsgericht Hildesheim, HRA 2686 | Fax:   +49-5121-206917-5555 |

--raq3yd6i5d77bb2l
Content-Type: application/pgp-signature; name="signature.asc"

-----BEGIN PGP SIGNATURE-----

iQEzBAABCgAdFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmB2ks4ACgkQqclaivrt
76mHgQf/QZQQBkLEljBddFitlXSkW2erh/AEf1A4VAjsY2cWJEcOrWAzCT5FLV+v
+kNI7gUwtFl8wB6eHnC9OVl7fsvYgqhukX+KPkw6BNESbrSgzB3QBzOHoZOseTpm
nMiKP8gcKM5RVsoXWdiVOuUibbN6iLwKZvBvY6Vww1iz2wwtnPWqT5EyEoKh0YzO
ZfV6/5KCYVYzoAU/Jowk+iNfiPq9928Z0ek3hJHo9jaddhONcQ/PWM73ob/wAD+I
e5ixdVWJQEsmVaw2mG4C8sYXoYvqKIqMxd9S+O3Lu49oZcBrkEsrK4dwyEi8mLmt
MEJYPENQoVsvsWkX+OvhDQqOrg1eug==
=EjJc
-----END PGP SIGNATURE-----

--raq3yd6i5d77bb2l--