Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
From:   Jonathan Marek <jonathan@marek.ca>
To:     linux-arm-msm@vger.kernel.org
Cc:     Andy Gross <agross@kernel.org>,
        Bjorn Andersson <bjorn.andersson@linaro.org>,
        Rob Herring <robh+dt@kernel.org>,
        devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND FLATTENED
        DEVICE TREE BINDINGS), linux-kernel@vger.kernel.org (open list)
Subject: [PATCH 2/2] arm64: dts: qcom: sm8350: add qupv3_id_1/i2c13 nodes
Date:   Thu, 13 May 2021 14:13:09 -0400
Message-Id: <20210513181309.12491-2-jonathan@marek.ca>
In-Reply-To: <20210513181309.12491-1-jonathan@marek.ca>
References: <20210513181309.12491-1-jonathan@marek.ca>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

Add the qupv3_id_1 node and the i2c13 child node used for i2c devices
connected to gpio0/gpio1.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
---
 arch/arm64/boot/dts/qcom/sm8350.dtsi | 38 ++++++++++++++++++++++++++++
 1 file changed, 38 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 76a1df371b17..b7b997dd1475 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -468,6 +468,31 @@ uart3: serial@98c000 {
 			};
 		};
 
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x00ac0000 0x0 0x6000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			i2c13: i2c@a94000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a94000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c13_default_state>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
 		apps_smmu: iommu@15000000 {
 			compatible = "qcom,sm8350-smmu-500", "arm,mmu-500";
 			reg = <0 0x15000000 0 0x100000>;
@@ -760,6 +785,19 @@ tx {
 					function = "qup3";
 				};
 			};
+
+			qup_i2c13_default_state: qup-i2c13-default-state {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "qup13";
+				};
+
+				config {
+					pins = "gpio0", "gpio1";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
 		};
 
 		rng: rng@10d3000 {
-- 
2.26.1