Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
From:   Peter Geis <pgwipeout@gmail.com>
To:     Andrew Lunn <andrew@lunn.ch>,
        Heiner Kallweit <hkallweit1@gmail.com>,
        Russell King <linux@armlinux.org.uk>,
        "David S . Miller" <davem@davemloft.net>,
        Jakub Kicinski <kuba@kernel.org>,
        Nathan Chancellor <nathan@kernel.org>
Cc:     netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
        clang-built-linux@googlegroups.com,
        Peter Geis <pgwipeout@gmail.com>,
        kernel test robot <lkp@intel.com>
Subject: [PATCH 2/2] net: phy: abort loading yt8511 driver in unsupported modes
Date:   Tue, 25 May 2021 08:26:15 -0400
Message-Id: <20210525122615.3972574-3-pgwipeout@gmail.com>
In-Reply-To: <20210525122615.3972574-1-pgwipeout@gmail.com>
References: <20210525122615.3972574-1-pgwipeout@gmail.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

While investigating the clang `ge` uninitialized variable report, it was
discovered the default switch would have unintended consequences. Due to
the switch to __phy_modify, the driver would modify the ID values in the
default scenario.

Fix this by promoting the interface mode switch and aborting when the
mode is not a supported RGMII mode.

This prevents the `ge` and `fe` variables from ever being used
uninitialized.

Fixes: b1b41c047f73 ("net: phy: add driver for Motorcomm yt8511 phy")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
---
 drivers/net/phy/motorcomm.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
index 5795f446c528..53178e978da7 100644
--- a/drivers/net/phy/motorcomm.c
+++ b/drivers/net/phy/motorcomm.c
@@ -53,15 +53,10 @@ static int yt8511_config_init(struct phy_device *phydev)
 	unsigned int ge, fe;
 	int oldpage, ret = 0;
 
-	/* set clock mode to 125mhz */
 	oldpage = phy_select_page(phydev, YT8511_EXT_CLK_GATE);
 	if (oldpage < 0)
 		goto err_restore_page;
 
-	ret = __phy_modify(phydev, YT8511_PAGE, 0, YT8511_CLK_125M);
-	if (ret < 0)
-		goto err_restore_page;
-
 	/* set rgmii delay mode */
 	switch (phydev->interface) {
 	case PHY_INTERFACE_MODE_RGMII:
@@ -80,14 +75,20 @@ static int yt8511_config_init(struct phy_device *phydev)
 		ge = YT8511_DELAY_RX | YT8511_DELAY_GE_TX_EN;
 		fe = YT8511_DELAY_FE_TX_EN;
 		break;
-	default: /* leave everything alone in other modes */
-		break;
+	default: /* do not support other modes */
+		ret = -EOPNOTSUPP;
+		goto err_restore_page;
 	}
 
 	ret = __phy_modify(phydev, YT8511_PAGE, (YT8511_DELAY_RX | YT8511_DELAY_GE_TX_EN), ge);
 	if (ret < 0)
 		goto err_restore_page;
 
+	/* set clock mode to 125mhz */
+	ret = __phy_modify(phydev, YT8511_PAGE, 0, YT8511_CLK_125M);
+	if (ret < 0)
+		goto err_restore_page;
+
 	/* fast ethernet delay is in a separate page */
 	ret = __phy_write(phydev, YT8511_PAGE_SELECT, YT8511_EXT_DELAY_DRIVE);
 	if (ret < 0)
-- 
2.25.1