Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
MIME-Version: 1.0
References: <1620990152-19255-1-git-send-email-dillon.minfei@gmail.com>
 <401eb514-27bd-03f6-f7a5-22604882b28a@foss.st.com> <CAL9mu0KScM+imZKVd8pfdm+8hDkRpvMVhGF6cgaEnNiLpkfjoA@mail.gmail.com>
 <980635c6-5abb-f440-0c3d-cf1ee2dd7bf1@foss.st.com>
In-Reply-To: <980635c6-5abb-f440-0c3d-cf1ee2dd7bf1@foss.st.com>
From:   Dillon Min <dillon.minfei@gmail.com>
Date:   Mon, 31 May 2021 22:29:27 +0800
Message-ID: <CAL9mu0LQAcQbq2Y2=hbrqf_qTuv5-41nD+Dkz57Las5uD1OssA@mail.gmail.com>
Subject: Re: [PATCH 0/4] Fix the i2c/clk bug of stm32 mcu platform
To:     Patrice CHOTARD <patrice.chotard@foss.st.com>
Cc:     pierre-yves.mordret@foss.st.com, alain.volmat@foss.st.com,
        Maxime Coquelin <mcoquelin.stm32@gmail.com>,
        Alexandre TORGUE <alexandre.torgue@foss.st.com>,
        Sumit Semwal <sumit.semwal@linaro.org>,
        christian.koenig@amd.com,
        Michael Turquette <mturquette@baylibre.com>,
        Stephen Boyd <sboyd@kernel.org>, linux-i2c@vger.kernel.org,
        linux-stm32@st-md-mailman.stormreply.com,
        Linux ARM <linux-arm-kernel@lists.infradead.org>,
        Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
        linux-media <linux-media@vger.kernel.org>,
        "open list:DRM PANEL DRIVERS" <dri-devel@lists.freedesktop.org>,
        linaro-mm-sig@lists.linaro.org,
        linux-clk <linux-clk@vger.kernel.org>
Content-Type: text/plain; charset="UTF-8"
Precedence: bulk

Hi Patrice

On Mon, May 31, 2021 at 9:51 PM Patrice CHOTARD
<patrice.chotard@foss.st.com> wrote:
>
>
>
> On 5/31/21 3:38 PM, Dillon Min wrote:
> > Hi Patrice
> >
> > Thanks for your time to test my patch.
> >
> > On Mon, May 31, 2021 at 9:20 PM Patrice CHOTARD
> > <patrice.chotard@foss.st.com> wrote:
> >>
> >> Hi Dillon
> >>
> >>
> >>
> >> On 5/14/21 1:02 PM, dillon.minfei@gmail.com wrote:
> >>> From: Dillon Min <dillon.minfei@gmail.com>
> >>>
> >>> This seriese fix three i2c/clk bug for stm32 f4/f7
> >>> - kernel runing in sdram, i2c driver get data timeout
> >>> - ltdc clk turn off after kernel console active
> >>> - kernel hang in set ltdc clock rate
> >>>
> >>> clk bug found on stm32f429/f469-disco board
> >>>
> >>> Hi Patrice:
> >>> below is the guide to verify the patch:
> >>>
> >>> setup test env with following files(link at below 'files link'):
> >>> [1] u-boot-dtb.bin
> >>> [2] rootfs zip file (used in kernel initramfs)
> >>> [3] u-boot's mkimage to create itb file
> >>> [4] kernel config file
> >>> [5] my itb with-or-without i2c patch
> >>>
> >>> This patch based on kernel commit:
> >>> 88b06399c9c766c283e070b022b5ceafa4f63f19
> >>>
> >>> Note:
> >>> panel-ilitek-ili9341.c is the driver which was submitted last year, but not
> >>> get accepted. it's used to setup touch screen calibration, then test i2c.
> >>>
> >>> create itb file(please correct path of 'data'):
> >>> ./mkimage -f stm32.its stm32.itb
> >>>
> >>> HW setup:
> >>> console:
> >>>        PA9, PA10
> >>>        usart0
> >>>        serial@40011000
> >>>        115200 8n1
> >>>
> >>> -- flash u-boot.bin to stm32f429-disco on PC
> >>> $ sudo openocd -f board/stm32f429discovery.cfg -c \
> >>>   '{PATH-TO-YOUR-UBOOT}/u-boot-dtb.bin 0x08000000 exit reset'
> >>>
> >>> -- setup kernel load bootargs at u-boot
> >>> U-Boot > setenv bootargs 'console=tty0 console=ttySTM0,115200
> >>>                     root=/dev/ram rdinit=/linuxrc loglevel=8 fbcon=rotate:2'
> >>> U-Boot > loady;bootm
> >>> (download stm32.dtb or your kernel with itb format, or download zImage, dtb)
> >>>
> >>
> >>
> >> Thanks for these informations
> >> I was able to load and boot DTB and uImage directly in SDRAM as you suggested,
> >> i saw Linux logo and kernel log on the STM32F429-disco display,
> >> but i can't reach the login.
> >>
> >> The last kernel log i got is :
> >>
> >> Starting kernel ...
> >>
> >> [    0.000000] Booting Linux on physical CPU 0x0
> >> [    0.000000] Linux version 5.13.0-rc1-00082-g9dbbd5cb6240-dirty (nxp11987@lmecxl0573.lme1
> >> [    0.000000] CPU: ARMv7-M [410fc241] revision 1 (ARMv7M), cr=00000000
> >> [    0.000000] CPU: unknown data cache, unknown instruction cache
> >> [    0.000000] OF: fdt: Machine model: STMicroelectronics STM32F429i-DISCO board
> >> [    0.000000] Zone ranges:
> >> [    0.000000]   Normal   [mem 0x0000000090000000-0x00000000907fffff]
> >> [    0.000000] Movable zone start for each node
> >> [    0.000000] Early memory node ranges
> >>
> >> [...]
> >>
> >> [    2.637564] printk: console [ttySTM0] enabled
> >> [    2.747984] panel-ilitek-ili9341 spi0.1: get optional vcc failed
> >> [    2.758986] spi_stm32 40015000.spi: driver initialized
> >> [    2.795733] i2c /dev entries driver
> >> [    2.849955] stmpe-i2c 0-0041: stmpe811 detected, chip id: 0x811
> >> [    2.922030] stmpe-ts stmpe-ts: DMA mask not set
> >> [    2.965729] input: stmpe-ts as /devices/platform/soc/40005c00.i2c/i2c-0/0-0041/stmpe-ts0
> >> [    2.991570] stm32f4-i2c 40005c00.i2c: STM32F4 I2C driver registered
> >> [    3.058262] [drm] Initialized stm 1.0.0 20170330 for 40016800.display-controller on min0
> >> [    3.665951] panel-ilitek-ili9341 spi0.1: initialized display rgb interface
> >> [    3.765208] Console: switching to colour frame buffer device 30x40
> >> [    4.014269] stm32-display 40016800.display-controller: [drm] fb0: stmdrmfb frame buffere
> >> [    4.212737] Freeing unused kernel memory: 324K
> >> [    4.287300] This architecture does not have kernel memory protection.
> >> [    4.401202] Run /linuxrc as init process
> >> [    4.478622]   with arguments:
> >> [    4.555069]     /linuxrc
> >> [    4.595406]   with environment:
> >> [    4.672213]     HOME=/
> >> [    4.712511]     TERM=linux
> >> [  206.785289] random: crng init done
> >
> > I guess you didn't add the rootfs to uImage I sent you.
>
> I do use your rootfs
>
> > Could you post all the logs from u-boot startup to kernel log end.
>
>
> U-Boot 2021.07-rc2 (May 28 2021 - 17:05:35 +0200)
>
> DRAM:  8 MiB
> Flash: 2 MiB
> Loading Environment from Flash... OK
> In:    serial@40011000
> Out:   serial@40011000
> Err:   serial@40011000
> Hit any key to stop autoboot:  0
> U-Boot >    setenv bootargs 'console=tty0 console=ttySTM0,115200 root=/dev/ram rdinit=/lin'

It seems bootargs are broken here.
should be setenv bootargs 'console=tty0 console=ttySTM0,115200
root=/dev/ram rdinit=/linuxrc loglevel=8 fbcon=rotate:2'

> U-Boot >
> U-Boot >
> U-Boot > setenv loadaddr 0x90400000
> U-Boot > loady
> ## Ready for binary (ymodem) download to 0x90400000 at 115200 bps...
> CxyzModem - CRC mode, 156(SOH)/0(STX)/0(CAN) packets, 7 retries
> ## Total Size      = 0x00004cad = 19629 Bytes
> U-Boot > setenv loadaddr 0x90406000
> U-Boot > loady
> ## Ready for binary (ymodem) download to 0x90406000 at 115200 bps...
> C- CRC mode, 12453(SOH)/0(STX)/0(CAN) packets, 4 retries
> ## Total Size      = 0x00185140 = 1593664 Bytes
> U-Boot > bootm 0x90406000 - 0x90400000
> ## Booting kernel from Legacy Image at 90406000 ...
>    Image Name:   Linux-5.13.0-rc1-00082-g9dbbd5cb
>    Image Type:   ARM Linux Kernel Image (uncompressed)
>    Data Size:    1593600 Bytes = 1.5 MiB
>    Load Address: 90008000
>    Entry Point:  90008000
>    Verifying Checksum ... OK
> ## Flattened Device Tree blob at 90400000
>    Booting using the fdt blob at 0x90400000
>    Loading Kernel Image
>    Loading Device Tree to 905b9000, end 905c0cac ... OK
>
> Starting kernel ...
>
> [    0.000000] Booting Linux on physical CPU 0x0
> [    0.000000] Linux version 5.13.0-rc1-00082-g9dbbd5cb6240-dirty (nxp11987@lmecxl0573.lme1
> [    0.000000] CPU: ARMv7-M [410fc241] revision 1 (ARMv7M), cr=00000000
> [    0.000000] CPU: unknown data cache, unknown instruction cache
> [    0.000000] OF: fdt: Machine model: STMicroelectronics STM32F429i-DISCO board
> [    0.000000] Zone ranges:
> [    0.000000]   Normal   [mem 0x0000000090000000-0x00000000907fffff]
> [    0.000000] Movable zone start for each node
> [    0.000000] Early memory node ranges
> [    0.000000]   node   0: [mem 0x0000000090000000-0x00000000907fffff]
> [    0.000000] Initmem setup node 0 [mem 0x0000000090000000-0x00000000907fffff]
> [    0.000000] On node 0 totalpages: 2048
> [    0.000000]   Normal zone: 16 pages used for memmap
> [    0.000000]   Normal zone: 0 pages reserved
> [    0.000000]   Normal zone: 2048 pages, LIFO batch:0
> [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> [    0.000000] pcpu-alloc: [0] 0
> [    0.000000] Built 1 zonelists, mobility grouping off.  Total pages: 2032
> [    0.000000] Kernel command line: console=tty0 console=ttySTM0,115200 root=/dev/ram rdin2

ditto

> [    0.000000] Dentry cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
> [    0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
> [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
> [    0.000000] Memory: 5264K/8192K available (1372K kernel code, 302K rwdata, 516K rodata,)
> [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> [    0.000000] rcu: Preemptible hierarchical RCU implementation.
> [    0.000000] rcu:     RCU event tracing is enabled.
> [    0.000000]  Trampoline variant of Tasks RCU enabled.
> [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
> [    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
> [    0.000000] /soc/interrupt-controller@40013c00: bank0
> [    0.000000] random: get_random_bytes called from start_kernel+0x203/0x370 with crng_ini0
> [    0.000000] clocksource: arm_system_timer: mask: 0xffffff max_cycles: 0xffffff, max_idls
> [    0.000000] ARM System timer initialized as clocksource
> [    0.000026] sched_clock: 32 bits at 90MHz, resolution 11ns, wraps every 23860929530ns
> [    0.000665] timer@40000c00: STM32 sched_clock registered
> [    0.001275] Switching to timer-based delay loop, resolution 11ns
> [    0.001712] timer@40000c00: STM32 delay timer registered
> [    0.002253] clocksource: timer@40000c00: mask: 0xffffffff max_cycles: 0xffffffff, max_is
> [    0.003076] /soc/timer@40000c00: STM32 clockevent driver initialized (32 bits)
> [    0.014135] Console: colour dummy device 80x30
> [    0.062375] printk: console [tty0] enabled
> [    0.063843] Calibrating delay loop (skipped), value calculated using timer frequency.. )
> [    0.066453] pid_max: default: 4096 minimum: 301
> [    0.071393] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
> [    0.073734] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
> [    0.104759] rcu: Hierarchical SRCU implementation.
> [    0.111552] devtmpfs: initialized
> [    0.339332] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns:s
> [    0.341835] pinctrl core: initialized pinctrl subsystem
> [    0.658423] stm32f429-pinctrl soc:pin-controller: No package detected, use default one
> [    0.680505] stm32f429-pinctrl soc:pin-controller: GPIOA bank added
> [    0.689824] stm32f429-pinctrl soc:pin-controller: GPIOB bank added
> [    0.699409] stm32f429-pinctrl soc:pin-controller: GPIOC bank added
> [    0.708775] stm32f429-pinctrl soc:pin-controller: GPIOD bank added
> [    0.718094] stm32f429-pinctrl soc:pin-controller: GPIOE bank added
> [    0.727535] stm32f429-pinctrl soc:pin-controller: GPIOF bank added
> [    0.736953] stm32f429-pinctrl soc:pin-controller: GPIOG bank added
> [    0.746404] stm32f429-pinctrl soc:pin-controller: GPIOH bank added
> [    0.756098] stm32f429-pinctrl soc:pin-controller: GPIOI bank added
> [    0.765436] stm32f429-pinctrl soc:pin-controller: GPIOJ bank added
> [    0.774870] stm32f429-pinctrl soc:pin-controller: GPIOK bank added
> [    0.776730] stm32f429-pinctrl soc:pin-controller: Pinctrl STM32 initialized
> [    0.997446] stm32-dma 40026000.dma-controller: STM32 DMA driver registered
> [    1.029604] stm32-dma 40026400.dma-controller: STM32 DMA driver registered
> [    1.043098] clocksource: Switched to clocksource timer@40000c00
> [    1.358086] workingset: timestamp_bits=30 max_order=11 bucket_order=0
> [    1.632751] io scheduler mq-deadline registered
> [    1.634287] io scheduler kyber registered
> [    1.650574] STM32 USART driver initialized
> [    1.661272] 40011000.serial: ttySTM0 at MMIO 0x40011000 (irq = 34, base_baud = 5625000)t
> [    2.603317] random: fast init done
> [    2.637564] printk: console [ttySTM0] enabled
> [    2.747984] panel-ilitek-ili9341 spi0.1: get optional vcc failed
> [    2.758986] spi_stm32 40015000.spi: driver initialized
> [    2.795733] i2c /dev entries driver
> [    2.849955] stmpe-i2c 0-0041: stmpe811 detected, chip id: 0x811
> [    2.922030] stmpe-ts stmpe-ts: DMA mask not set
> [    2.965729] input: stmpe-ts as /devices/platform/soc/40005c00.i2c/i2c-0/0-0041/stmpe-ts0
> [    2.991570] stm32f4-i2c 40005c00.i2c: STM32F4 I2C driver registered
> [    3.058262] [drm] Initialized stm 1.0.0 20170330 for 40016800.display-controller on min0
> [    3.665951] panel-ilitek-ili9341 spi0.1: initialized display rgb interface
> [    3.765208] Console: switching to colour frame buffer device 30x40
> [    4.014269] stm32-display 40016800.display-controller: [drm] fb0: stmdrmfb frame buffere
> [    4.212737] Freeing unused kernel memory: 324K
> [    4.287300] This architecture does not have kernel memory protection.
> [    4.401202] Run /linuxrc as init process
> [    4.478622]   with arguments:
> [    4.555069]     /linuxrc
> [    4.595406]   with environment:
> [    4.672213]     HOME=/
> [    4.712511]     TERM=linux
> [  206.785289] random: crng init done
>
>
> >
> > If possible, you can try my suggestion.
> > - tar -jxf stm32_rootfs.tar.bz2
> > - add stm32_rootfs to your kernel config( enable initramfs)
>
> As explained above, that's what i did
>
> > - make O=YOUR_KERNEL_OUT zImage dtbs LOADADDR=0x90008000
>
>
>
> > - create itb file (combine dtb and kernel, initramfs) by mkimage
> >   ./mkimage -f stm32.its stm32.itb
>
> I didn't use .itb file, but directly uImage loaded @0x90406000 and stm32f429-disco.dtb loaded @0x90400000

It's fine with manual load dtb and uImage.

>
> How do you generate .its file ?

I refer to u-boot doc , U-BOOT-SOURCE/doc/uImage.FIT/kernel.its
you can just change the PATH('data = ' filed) of my stm32.its.
you can correct bootargs in u-boot, try again

good luck.

Thanks

Best Regards
Dillon

>
>
> >   (before above command, make sure you correct stm32.its adapt to your env)
> >
> > This process will make u-boot to load the kernel more simple.
> >
> > Thanks.
> >
> > Best Regards.
> > Dillon
> >
> >
> >>
> >>
> >> I can't test your I2C patch.
> >>
> >> Patrice
> >>
> >>
> >>> -- setup ts_calibrate running env on stm32f429-disco
> >>> / # export TSLIB_CONFFILE=/etc/ts.conf
> >>> / # export TSLIB_TSDEVICE=/dev/input/event0
> >>> / # export TSLIB_CONSOLEDEVICE=none
> >>> / # export TSLIB_FBDEVICE=/dev/fb0
> >>>
> >>> -- clear screen
> >>> / # ./fb
> >>>
> >>> -- run ts_calibrate
> >>> / # ts_calibrate
> >>> (you can calibrate touchscreen now, and get below errors)
> >>>
> >>> [  113.942087] stmpe-i2c0-0041: failed to read regs 0x52: -110
> >>> [  114.063598] stmpe-i2c 0-0041: failed to read reg 0x4b: -16
> >>> [  114.185629] stmpe-i2c 0-0041: failed to read reg 0x40: -16
> >>> [  114.307257] stmpe-i2c 0-0041: failed to write reg 0xb: -16
> >>>
> >>> ...
> >>> with i2c patch applied, you will find below logs:
> >>>
> >>> RAW---------------------> 3164 908 183 118.110884
> >>> TS_READ_RAW----> x = 3164, y =908, pressure = 183
> >>> RAW---------------------> 3166 922 126 118.138946
> >>> TS_READ_RAW----> x = 3166, y = 922, pressure = 126
> >>> ....
> >>>
> >>> files link:
> >>> https://drive.google.com/drive/folders/1qNbjChcB6UGtKzne2F5x9_WG_sZFyo3o?usp=sharing
> >>>
> >>>
> >>>
> >>>
> >>> Dillon Min (4):
> >>>   drm/panel: Add ilitek ili9341 panel driver
> >>>   i2c: stm32f4: Fix stmpe811 get xyz data timeout issue
> >>>   clk: stm32: Fix stm32f429's ltdc driver hang in set clock rate
> >>>   clk: stm32: Fix ltdc's clock turn off by clk_disable_unused() after
> >>>     kernel startup
> >>>
> >>>  drivers/clk/clk-stm32f4.c                    |   10 +-
> >>>  drivers/gpu/drm/panel/Kconfig                |   12 +
> >>>  drivers/gpu/drm/panel/Makefile               |    1 +
> >>>  drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 1285 ++++++++++++++++++++++++++
> >>>  drivers/i2c/busses/i2c-stm32f4.c             |   12 +-
> >>>  5 files changed, 1310 insertions(+), 10 deletions(-)
> >>>  create mode 100755 drivers/gpu/drm/panel/panel-ilitek-ili9341.c
> >>>