Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
Date:   Fri, 11 Jun 2021 10:14:22 +0300
From:   Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
To:     Manivannan Sadhasivam <mani@kernel.org>
Cc:     Rob Herring <robh+dt@kernel.org>,
        Andreas =?iso-8859-1?Q?F=E4rber?= <afaerber@suse.de>,
        devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
        linux-actions@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH 2/2] ARM: dts: owl-s500-roseapplepi: Add ethernet support
Message-ID: <20210611071422.GB1520454@BV030612LT>
References: <cover.1623358117.git.cristian.ciocaltea@gmail.com>
 <632e12c445ced7f10e6d7240162484ae5afc148e.1623358117.git.cristian.ciocaltea@gmail.com>
 <20210611055606.GB6950@thinkpad>
 <20210611063147.GA1520454@BV030612LT>
 <20210611063940.GD6950@thinkpad>
MIME-Version: 1.0
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
In-Reply-To: <20210611063940.GD6950@thinkpad>
Precedence: bulk

On Fri, Jun 11, 2021 at 12:09:40PM +0530, Manivannan Sadhasivam wrote:
> On Fri, Jun 11, 2021 at 09:31:47AM +0300, Cristian Ciocaltea wrote:
> > On Fri, Jun 11, 2021 at 11:26:06AM +0530, Manivannan Sadhasivam wrote:
> > > On Fri, Jun 11, 2021 at 12:09:22AM +0300, Cristian Ciocaltea wrote:
> > > > Add pinctrl configuration for enabling the Ethernet MAC on RoseapplePi
> > > > SBC. Additionally, provide the necessary properties for the generic S500
> > > > ethernet node in order to setup PHY and MDIO.
> > > > 
> > > > Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
> > > > ---
> > > >  arch/arm/boot/dts/owl-s500-roseapplepi.dts | 56 ++++++++++++++++++++++
> > > >  1 file changed, 56 insertions(+)
> > > > 
> > > > diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> > > > index b8c5db2344aa..bffabc7eaa50 100644
> > > > --- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> > > > +++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> 
> [...]
> 
> > > > +	mdio {
> > > > +		#address-cells = <1>;
> > > > +		#size-cells = <0>;
> > > > +
> > > > +		reset-gpios = <&pinctrl 88 GPIO_ACTIVE_LOW>; /* GPIOC24 */
> > > > +		reset-delay-us = <10000>;
> > > > +		reset-post-delay-us = <150000>;
> > > 
> > > reset-* properties belong to "ethernet-phy" node. Also, while adding new nodes
> > > please run the dtbs_check and try to address the warnings.
> > 
> > The properties are those described in Documentation/devicetree/bindings/net/mdio.yaml
> 
> Do you mean the reset properties are applicable for all PHYs in this SoC?

Actually there is only one PHY connected. I've also checked the vendor
code and didn't notice any special handling for the PHY reset.

> > The dtbs_check doesn't report any issues in my case, usually this
> > happens when dtschema is not updated to the latest version. I always
> > run the following command after rebasing to a new kernel version:
> > 
> >   pip3 install --upgrade dtschema
> > 
> 
> That's good!
> 
> Thanks,
> Mani
> 
> > Thanks for the review,
> > Cristi
> > 
> > > Thanks,
> > > Mani
> > > 
> > > > +
> > > > +		eth_phy: ethernet-phy@3 {
> > > > +			reg = <0x3>;
> > > > +			max-speed = <100>;
> > > > +			interrupt-parent = <&sirq>;
> > > > +			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> > > > +		};
> > > > +	};
> > > > +};
> > > > +
> > > >  &twd_timer {
> > > >  	status = "okay";
> > > >  };
> > > > -- 
> > > > 2.32.0
> > > >