Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
From:   Lokesh Vutla <lokeshvutla@ti.com>
To:     Nishanth Menon <nm@ti.com>, <kristo@kernel.org>
CC:     Device Tree Mailing List <devicetree@vger.kernel.org>,
        Rob Herring <robh+dt@kernel.org>,
        Linux ARM Mailing List <linux-arm-kernel@lists.infradead.org>,
        <linux-kernel@vger.kernel.org>, Vignesh R <vigneshr@ti.com>,
        Lokesh Vutla <lokeshvutla@ti.com>
Subject: [PATCH v2 4/4] arm64: dts: ti: k3-am642-sk: Add pwm nodes
Date:   Wed, 21 Jul 2021 17:06:25 +0530
Message-ID: <20210721113625.17299-5-lokeshvutla@ti.com>
In-Reply-To: <20210721113625.17299-1-lokeshvutla@ti.com>
References: <20210721113625.17299-1-lokeshvutla@ti.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Content-Type: text/plain
Precedence: bulk

ecap0 can be configured to use pad ECAP0_IN_APWM_OUT (D18) which has a
signal connected to Pin 1 of J3. Add support for adding this pinmux so
that pwm can be observed on pin 1 of Header J3

Also mark all un-used epwm and ecap pwm nodes as disabled.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am642-sk.dts | 64 ++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am642-sk.dts b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
index d3aa2901e6fd..6b45cdeeeefa 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
@@ -210,6 +210,12 @@ AM64X_IOPAD(0x0028, PIN_INPUT, 0) /* (M17) OSPI0_D7 */
 			AM64X_IOPAD(0x0008, PIN_INPUT, 0) /* (N19) OSPI0_DQS */
 		>;
 	};
+
+	main_ecap0_pins_default: main-ecap0-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0270, PIN_INPUT, 0) /* (D18) ECAP0_IN_APWM_OUT */
+		>;
+	};
 };
 
 &mcu_uart0 {
@@ -453,3 +459,61 @@ &pcie0_rc {
 &pcie0_ep {
 	status = "disabled";
 };
+
+&ecap0 {
+	/* PWM is available on Pin 1 of header J3 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_ecap0_pins_default>;
+};
+
+&ecap1 {
+	status = "disabled";
+};
+
+&ecap2 {
+	status = "disabled";
+};
+
+&epwm0 {
+	status = "disabled";
+};
+
+&epwm1 {
+	status = "disabled";
+};
+
+&epwm2 {
+	status = "disabled";
+};
+
+&epwm3 {
+	status = "disabled";
+};
+
+&epwm4 {
+	/*
+	 * EPWM4_A, EPWM4_B is available on Pin 32 and 33 on J4 (RPi hat)
+	 * But RPi Hat will be used for other use cases, so marking epwm4 as disabled.
+	 */
+	status = "disabled";
+};
+
+&epwm5 {
+	/*
+	 * EPWM5_A, EPWM5_B is available on Pin 29 and 31 on J4 (RPi hat)
+	 * But RPi Hat will be used for other use cases, so marking epwm5 as disabled.
+	 */
+	status = "disabled";
+};
+
+&epwm6 {
+	status = "disabled";
+};
+
+&epwm7 {
+	status = "disabled";
+};
+
+&epwm8 {
+	status = "disabled";
+};
-- 
2.31.1