Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
Date:   Fri, 6 Aug 2021 21:08:40 +0200
From:   Miquel Raynal <miquel.raynal@bootlin.com>
To:     Apurva Nandan <a-nandan@ti.com>
Cc:     Richard Weinberger <richard@nod.at>,
        Vignesh Raghavendra <vigneshr@ti.com>,
        Mark Brown <broonie@kernel.org>,
        Patrice Chotard <patrice.chotard@foss.st.com>,
        Boris Brezillon <boris.brezillon@collabora.com>,
        <linux-mtd@lists.infradead.org>, <linux-kernel@vger.kernel.org>,
        <linux-spi@vger.kernel.org>, Pratyush Yadav <p.yadav@ti.com>
Subject: Re: [PATCH 11/13] mtd: spinand: Add support for Power-on-Reset
 (PoR) instruction
Message-ID: <20210806210840.65c06b67@xps13>
In-Reply-To: <20210713130538.646-12-a-nandan@ti.com>
References: <20210713130538.646-1-a-nandan@ti.com>
        <20210713130538.646-12-a-nandan@ti.com>
Organization: Bootlin
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8BIT
Precedence: bulk

Hi Apurva,

Apurva Nandan <a-nandan@ti.com> wrote on Tue, 13 Jul 2021 13:05:36
+0000:

> Manufacturers like Gigadevice and Winbond are adding Power-on-Reset
> functionality in their SPI NAND flash chips. PoR instruction consists
> of a 66h command followed by 99h command, and is different from the FFh
> reset. The reset command FFh just clears the status only registers,
> while the PoR command erases all the configurations written to the
> flash and is equivalent to a power-down -> power-up cycle.
> 
> Add support for the Power-on-Reset command for any flash that provides
> this feature.
> 
> Datasheet: https://www.winbond.com/export/sites/winbond/datasheet/W35N01JW_Datasheet_Brief.pdf
> 
> Signed-off-by: Apurva Nandan <a-nandan@ti.com>
> ---

[...]
				\
> @@ -218,6 +230,8 @@ struct spinand_device;
>   * reading/programming/erasing when the RESET occurs. Since we always
>   * issue a RESET when the device is IDLE, 5us is selected for both initial
>   * and poll delay.
> + * Power on Reset can take max upto 500 us to complete, so sleep for 1000 us

s/max upto/up to/

> + * to 1200 us safely.

I don't really get why, if the maximum is 500, then let's wait for
500us.

>   */
>  #define SPINAND_READ_INITIAL_DELAY_US	6
>  #define SPINAND_READ_POLL_DELAY_US	5
> @@ -227,6 +241,8 @@ struct spinand_device;
>  #define SPINAND_WRITE_POLL_DELAY_US	15
>  #define SPINAND_ERASE_INITIAL_DELAY_US	250
>  #define SPINAND_ERASE_POLL_DELAY_US	50
> +#define SPINAND_POR_MIN_DELAY_US	1000
> +#define SPINAND_POR_MAX_DELAY_US	1200
>  
>  #define SPINAND_WAITRDY_TIMEOUT_MS	400
>  
> @@ -351,6 +367,7 @@ struct spinand_ecc_info {
>  #define SPINAND_HAS_QE_BIT		BIT(0)
>  #define SPINAND_HAS_CR_FEAT_BIT		BIT(1)
>  #define SPINAND_HAS_OCTAL_DTR_BIT	BIT(2)
> +#define SPINAND_HAS_POR_CMD_BIT		BIT(3)
>  
>  /**
>   * struct spinand_ondie_ecc_conf - private SPI-NAND on-die ECC engine structure


Thanks,
Miquèl