Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
From:   Paul Kocialkowski <paul.kocialkowski@bootlin.com>
To:     linux-media@vger.kernel.org, devicetree@vger.kernel.org,
        linux-arm-kernel@lists.infradead.org, linux-sunxi@lists.linux.dev,
        linux-kernel@vger.kernel.org, linux-phy@lists.infradead.org,
        linux-clk@vger.kernel.org, linux-staging@lists.linux.dev
Cc:     Yong Deng <yong.deng@magewell.com>,
        Mauro Carvalho Chehab <mchehab@kernel.org>,
        Rob Herring <robh+dt@kernel.org>,
        Maxime Ripard <mripard@kernel.org>,
        Sakari Ailus <sakari.ailus@linux.intel.com>,
        Hans Verkuil <hans.verkuil@cisco.com>,
        Chen-Yu Tsai <wens@csie.org>,
        Jernej Skrabec <jernej.skrabec@gmail.com>,
        Paul Kocialkowski <paul.kocialkowski@bootlin.com>,
        Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
        Helen Koike <helen.koike@collabora.com>,
        Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
        Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Subject: [PATCH 09/22] ARM: dts: sun8i: v3s: Add nodes for MIPI CSI-2 support
Date:   Fri, 10 Sep 2021 20:41:34 +0200
Message-Id: <20210910184147.336618-10-paul.kocialkowski@bootlin.com>
In-Reply-To: <20210910184147.336618-1-paul.kocialkowski@bootlin.com>
References: <20210910184147.336618-1-paul.kocialkowski@bootlin.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

MIPI CSI-2 is supported on the V3s with an A31-based MIPI CSI-2 bridge
controller. The controller uses a separate D-PHY, which is the same
that is otherwise used for MIPI DSI, but used in Rx mode.

On the V3s, the CSI0 controller is dedicated to MIPI CSI-2 as it does
not have access to any parallel interface pins.

Add all the necessary nodes (CSI0, MIPI CSI-2 bridge and D-PHY) to
support the MIPI CSI-2 interface.

Note that a fwnode graph link is created between CSI0 and MIPI CSI-2
even when no sensor is connected. This will result in a probe failure
for the controller as long as no sensor is connected but this is fine
since no other interface is available.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
---
 arch/arm/boot/dts/sun8i-v3s.dtsi | 72 ++++++++++++++++++++++++++++++++
 1 file changed, 72 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index a77b63362a1d..ec7fa6459547 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -612,6 +612,34 @@ spi0: spi@1c68000 {
 			#size-cells = <0>;
 		};
 
+		csi0: camera@1cb0000 {
+			compatible = "allwinner,sun8i-v3s-csi";
+			reg = <0x01cb0000 0x1000>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI1_SCLK>,
+				 <&ccu CLK_DRAM_CSI>;
+			clock-names = "bus", "mod", "ram";
+			resets = <&ccu RST_BUS_CSI>;
+			status = "disabled";
+
+			assigned-clocks = <&ccu CLK_CSI1_SCLK>;
+			assigned-clock-parents = <&ccu CLK_PLL_ISP>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@1 {
+					reg = <1>;
+
+					csi0_in_mipi_csi2: endpoint {
+						remote-endpoint = <&mipi_csi2_out_csi0>;
+					};
+				};
+			};
+		};
+
 		csi1: camera@1cb4000 {
 			compatible = "allwinner,sun8i-v3s-csi";
 			reg = <0x01cb4000 0x3000>;
@@ -637,5 +665,49 @@ gic: interrupt-controller@1c81000 {
 			#interrupt-cells = <3>;
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
+
+		mipi_csi2: csi@1cb1000 {
+			compatible = "allwinner,sun8i-v3s-mipi-csi2",
+				     "allwinner,sun6i-a31-mipi-csi2";
+			reg = <0x01cb1000 0x1000>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI1_SCLK>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_CSI>;
+			status = "disabled";
+
+			phys = <&dphy>;
+			phy-names = "dphy";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mipi_csi2_in: port@0 {
+					reg = <0>;
+				};
+
+				mipi_csi2_out: port@1 {
+					reg = <1>;
+
+					mipi_csi2_out_csi0: endpoint {
+						remote-endpoint = <&csi0_in_mipi_csi2>;
+					};
+				};
+			};
+		};
+
+		dphy: d-phy@1cb2000 {
+			compatible = "allwinner,sun6i-a31-mipi-dphy";
+			reg = <0x01cb2000 0x1000>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_MIPI_CSI>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_CSI>;
+			allwinner,direction = "rx";
+			status = "disabled";
+			#phy-cells = <0>;
+		};
 	};
 };
-- 
2.32.0