Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
Date:   Fri, 22 Oct 2021 10:25:35 -0700
From:   Bjorn Andersson <bjorn.andersson@linaro.org>
To:     Pavel Machek <pavel@ucw.cz>, Rob Herring <robh+dt@kernel.org>,
        Andy Gross <agross@kernel.org>,
        Thierry Reding <thierry.reding@gmail.com>,
        Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>,
        Lee Jones <lee.jones@linaro.org>
Cc:     linux-leds@vger.kernel.org, devicetree@vger.kernel.org,
        linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
        linux-pwm@vger.kernel.org,
        Marijn Suijten <marijn.suijten@somainline.org>,
        Yassine Oudjana <y.oudjana@protonmail.com>,
        Luca Weiss <luca@z3ntu.xyz>,
        Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Subject: Re: [PATCH v10 2/2] leds: Add driver for Qualcomm LPG
Message-ID: <YXL0DyyPkS4/wfB7@ripper>
References: <20211010043912.136640-1-bjorn.andersson@linaro.org>
 <20211010043912.136640-2-bjorn.andersson@linaro.org>
MIME-Version: 1.0
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
In-Reply-To: <20211010043912.136640-2-bjorn.andersson@linaro.org>
Precedence: bulk

On Sat 09 Oct 21:39 PDT 2021, Bjorn Andersson wrote:

> The Light Pulse Generator (LPG) is a PWM-block found in a wide range of
> PMICs from Qualcomm. These PMICs typically comes with 1-8 LPG instances,
> with their output being routed to various other components, such as
> current sinks or GPIOs.
> 
> Each LPG instance can operate on fixed parameters or based on a shared
> lookup-table, altering the duty cycle over time. This provides the means
> for hardware assisted transitions of LED brightness.
> 
> A typical use case for the fixed parameter mode is to drive a PWM
> backlight control signal, the driver therefor allows each LPG instance
> to be exposed to the kernel either through the LED framework or the PWM
> framework.
> 
> A typical use case for the LED configuration is to drive RGB LEDs in
> smartphones etc, for which the driver support multiple channels to be
> ganged up to a MULTICOLOR LED. In this configuration the pattern
> generators will be synchronized, to allow for multi-color patterns.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---

Any feedback on this?

Thanks,
Bjorn

> 
> Change since v9:
> - Replac magic 381 second as upper bound of period length
> - Declare variables inside the blocks where they are used in lpg_calc_freq()
> - Reworked duty calculation to avoid loosing precision
> - Reject inverted polarity in pwm_apply
> 
>  drivers/leds/Kconfig             |    3 +
>  drivers/leds/Makefile            |    3 +
>  drivers/leds/rgb/Kconfig         |   13 +
>  drivers/leds/rgb/Makefile        |    3 +
>  drivers/leds/rgb/leds-qcom-lpg.c | 1302 ++++++++++++++++++++++++++++++
>  5 files changed, 1324 insertions(+)
>  create mode 100644 drivers/leds/rgb/Kconfig
>  create mode 100644 drivers/leds/rgb/Makefile
>  create mode 100644 drivers/leds/rgb/leds-qcom-lpg.c
> 
> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
> index ed800f5da7d8..ffb8777842ff 100644
> --- a/drivers/leds/Kconfig
> +++ b/drivers/leds/Kconfig
> @@ -876,6 +876,9 @@ source "drivers/leds/blink/Kconfig"
>  comment "Flash and Torch LED drivers"
>  source "drivers/leds/flash/Kconfig"
>  
> +comment "RGB LED drivers"
> +source "drivers/leds/rgb/Kconfig"
> +
>  comment "LED Triggers"
>  source "drivers/leds/trigger/Kconfig"
>  
> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
> index c636ec069612..351153f84070 100644
> --- a/drivers/leds/Makefile
> +++ b/drivers/leds/Makefile
> @@ -100,6 +100,9 @@ obj-$(CONFIG_LEDS_USER)			+= uleds.o
>  # Flash and Torch LED Drivers
>  obj-$(CONFIG_LEDS_CLASS_FLASH)		+= flash/
>  
> +# RGB LED Drivers
> +obj-$(CONFIG_LEDS_CLASS_MULTICOLOR)	+= rgb/
> +
>  # LED Triggers
>  obj-$(CONFIG_LEDS_TRIGGERS)		+= trigger/
>  
> diff --git a/drivers/leds/rgb/Kconfig b/drivers/leds/rgb/Kconfig
> new file mode 100644
> index 000000000000..20be3e11fe4a
> --- /dev/null
> +++ b/drivers/leds/rgb/Kconfig
> @@ -0,0 +1,13 @@
> +# SPDX-License-Identifier: GPL-2.0
> +
> +if LEDS_CLASS_MULTICOLOR
> +
> +config LEDS_QCOM_LPG
> +	tristate "LED support for Qualcomm LPG"
> +	depends on OF
> +	depends on SPMI
> +	help
> +	  This option enables support for the Light Pulse Generator found in a
> +	  wide variety of Qualcomm PMICs.
> +
> +endif # LEDS_CLASS_MULTICOLOR
> diff --git a/drivers/leds/rgb/Makefile b/drivers/leds/rgb/Makefile
> new file mode 100644
> index 000000000000..83114f44c4ea
> --- /dev/null
> +++ b/drivers/leds/rgb/Makefile
> @@ -0,0 +1,3 @@
> +# SPDX-License-Identifier: GPL-2.0
> +
> +obj-$(CONFIG_LEDS_QCOM_LPG)	+= leds-qcom-lpg.o
> diff --git a/drivers/leds/rgb/leds-qcom-lpg.c b/drivers/leds/rgb/leds-qcom-lpg.c
> new file mode 100644
> index 000000000000..45ef4ec5ff17
> --- /dev/null
> +++ b/drivers/leds/rgb/leds-qcom-lpg.c
> @@ -0,0 +1,1302 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2017-2021 Linaro Ltd
> + * Copyright (c) 2010-2012, The Linux Foundation. All rights reserved.
> + */
> +#include <linux/bits.h>
> +#include <linux/led-class-multicolor.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/pwm.h>
> +#include <linux/regmap.h>
> +#include <linux/slab.h>
> +
> +#define LPG_PATTERN_CONFIG_REG	0x40
> +#define LPG_SIZE_CLK_REG	0x41
> +#define LPG_PREDIV_CLK_REG	0x42
> +#define PWM_TYPE_CONFIG_REG	0x43
> +#define PWM_VALUE_REG		0x44
> +#define PWM_ENABLE_CONTROL_REG	0x46
> +#define PWM_SYNC_REG		0x47
> +#define LPG_RAMP_DURATION_REG	0x50
> +#define LPG_HI_PAUSE_REG	0x52
> +#define LPG_LO_PAUSE_REG	0x54
> +#define LPG_HI_IDX_REG		0x56
> +#define LPG_LO_IDX_REG		0x57
> +#define PWM_SEC_ACCESS_REG	0xd0
> +#define PWM_DTEST_REG(x)	(0xe2 + (x) - 1)
> +
> +#define TRI_LED_SRC_SEL		0x45
> +#define TRI_LED_EN_CTL		0x46
> +#define TRI_LED_ATC_CTL		0x47
> +
> +#define LPG_LUT_REG(x)		(0x40 + (x) * 2)
> +#define RAMP_CONTROL_REG	0xc8
> +
> +#define LPG_RESOLUTION		512
> +#define LPG_MAX_M		7
> +
> +struct lpg_channel;
> +struct lpg_data;
> +
> +/**
> + * struct lpg - LPG device context
> + * @dev:	struct device for LPG device
> + * @map:	regmap for register access
> + * @pwm:	PWM-chip object, if operating in PWM mode
> + * @data:	reference to version specific data
> + * @lut_base:	base address of the LUT block (optional)
> + * @lut_size:	number of entries in the LUT block
> + * @lut_bitmap:	allocation bitmap for LUT entries
> + * @triled_base: base address of the TRILED block (optional)
> + * @triled_src:	power-source for the TRILED
> + * @triled_has_atc_ctl:	true if there is TRI_LED_ATC_CTL register
> + * @triled_has_src_sel:	true if there is TRI_LED_SRC_SEL register
> + * @channels:	list of PWM channels
> + * @num_channels: number of @channels
> + */
> +struct lpg {
> +	struct device *dev;
> +	struct regmap *map;
> +
> +	struct pwm_chip pwm;
> +
> +	const struct lpg_data *data;
> +
> +	u32 lut_base;
> +	u32 lut_size;
> +	unsigned long *lut_bitmap;
> +
> +	u32 triled_base;
> +	u32 triled_src;
> +	bool triled_has_atc_ctl;
> +	bool triled_has_src_sel;
> +
> +	struct lpg_channel *channels;
> +	unsigned int num_channels;
> +};
> +
> +/**
> + * struct lpg_channel - per channel data
> + * @lpg:	reference to parent lpg
> + * @base:	base address of the PWM channel
> + * @triled_mask: mask in TRILED to enable this channel
> + * @lut_mask:	mask in LUT to start pattern generator for this channel
> + * @in_use:	channel is exposed to LED framework
> + * @color:	color of the LED attached to this channel
> + * @dtest_line:	DTEST line for output, or 0 if disabled
> + * @dtest_value: DTEST line configuration
> + * @pwm_value:	duty (in microseconds) of the generated pulses, overridden by LUT
> + * @enabled:	output enabled?
> + * @period:	period (in nanoseconds) of the generated pulses
> + * @clk:	base frequency of the clock generator
> + * @pre_div:	divider of @clk
> + * @pre_div_exp: exponential divider of @clk
> + * @ramp_enabled: duty cycle is driven by iterating over lookup table
> + * @ramp_ping_pong: reverse through pattern, rather than wrapping to start
> + * @ramp_oneshot: perform only a single pass over the pattern
> + * @ramp_reverse: iterate over pattern backwards
> + * @ramp_tick_ms: length (in milliseconds) of one step in the pattern
> + * @ramp_lo_pause_ms: pause (in milliseconds) before iterating over pattern
> + * @ramp_hi_pause_ms: pause (in milliseconds) after iterating over pattern
> + * @pattern_lo_idx: start index of associated pattern
> + * @pattern_hi_idx: last index of associated pattern
> + */
> +struct lpg_channel {
> +	struct lpg *lpg;
> +
> +	u32 base;
> +	unsigned int triled_mask;
> +	unsigned int lut_mask;
> +
> +	bool in_use;
> +
> +	int color;
> +
> +	u32 dtest_line;
> +	u32 dtest_value;
> +
> +	u16 pwm_value;
> +	bool enabled;
> +
> +	u64 period;
> +	unsigned int clk;
> +	unsigned int pre_div;
> +	unsigned int pre_div_exp;
> +
> +	bool ramp_enabled;
> +	bool ramp_ping_pong;
> +	bool ramp_oneshot;
> +	bool ramp_reverse;
> +	unsigned long ramp_tick_ms;
> +	unsigned long ramp_lo_pause_ms;
> +	unsigned long ramp_hi_pause_ms;
> +
> +	unsigned int pattern_lo_idx;
> +	unsigned int pattern_hi_idx;
> +};
> +
> +/**
> + * struct lpg_led - logical LED object
> + * @lpg:		lpg context reference
> + * @cdev:		LED class device
> + * @mcdev:		Multicolor LED class device
> + * @num_channels:	number of @channels
> + * @channels:		list of channels associated with the LED
> + */
> +struct lpg_led {
> +	struct lpg *lpg;
> +
> +	struct led_classdev cdev;
> +	struct led_classdev_mc mcdev;
> +
> +	unsigned int num_channels;
> +	struct lpg_channel *channels[];
> +};
> +
> +/**
> + * struct lpg_channel_data - per channel initialization data
> + * @base:		base address for PWM channel registers
> + * @triled_mask:	bitmask for controlling this channel in TRILED
> + */
> +struct lpg_channel_data {
> +	unsigned int base;
> +	u8 triled_mask;
> +};
> +
> +/**
> + * struct lpg_data - initialization data
> + * @lut_base:		base address of LUT block
> + * @lut_size:		number of entries in LUT
> + * @triled_base:	base address of TRILED
> + * @triled_has_atc_ctl:	true if there is TRI_LED_ATC_CTL register
> + * @triled_has_src_sel:	true if there is TRI_LED_SRC_SEL register
> + * @pwm_9bit_mask:	bitmask for switching from 6bit to 9bit pwm
> + * @num_channels:	number of channels in LPG
> + * @channels:		list of channel initialization data
> + */
> +struct lpg_data {
> +	unsigned int lut_base;
> +	unsigned int lut_size;
> +	unsigned int triled_base;
> +	bool triled_has_atc_ctl;
> +	bool triled_has_src_sel;
> +	unsigned int pwm_9bit_mask;
> +	int num_channels;
> +	const struct lpg_channel_data *channels;
> +};
> +
> +static int triled_set(struct lpg *lpg, unsigned int mask, unsigned int enable)
> +{
> +	/* Skip if we don't have a triled block */
> +	if (!lpg->triled_base)
> +		return 0;
> +
> +	return regmap_update_bits(lpg->map, lpg->triled_base + TRI_LED_EN_CTL,
> +				  mask, enable);
> +}
> +
> +static int lpg_lut_store(struct lpg *lpg, struct led_pattern *pattern,
> +			 size_t len, unsigned int *lo_idx, unsigned int *hi_idx)
> +{
> +	unsigned int idx;
> +	u16 val;
> +	int i;
> +
> +	/* Hardware does not behave when LO_IDX == HI_IDX */
> +	if (len == 1)
> +		return -EINVAL;
> +
> +	idx = bitmap_find_next_zero_area(lpg->lut_bitmap, lpg->lut_size,
> +					 0, len, 0);
> +	if (idx >= lpg->lut_size)
> +		return -ENOMEM;
> +
> +	for (i = 0; i < len; i++) {
> +		val = pattern[i].brightness;
> +
> +		regmap_bulk_write(lpg->map, lpg->lut_base + LPG_LUT_REG(idx + i),
> +				  &val, sizeof(val));
> +	}
> +
> +	bitmap_set(lpg->lut_bitmap, idx, len);
> +
> +	*lo_idx = idx;
> +	*hi_idx = idx + len - 1;
> +
> +	return 0;
> +}
> +
> +static void lpg_lut_free(struct lpg *lpg, unsigned int lo_idx, unsigned int hi_idx)
> +{
> +	int len;
> +
> +	if (lo_idx == hi_idx)
> +		return;
> +
> +	len = hi_idx - lo_idx + 1;
> +	bitmap_clear(lpg->lut_bitmap, lo_idx, len);
> +}
> +
> +static int lpg_lut_sync(struct lpg *lpg, unsigned int mask)
> +{
> +	return regmap_write(lpg->map, lpg->lut_base + RAMP_CONTROL_REG, mask);
> +}
> +
> +static const unsigned int lpg_clk_rates[] = {1024, 32768, 19200000};
> +static const unsigned int lpg_pre_divs[] = {1, 3, 5, 6};
> +
> +static int lpg_calc_freq(struct lpg_channel *chan, uint64_t period)
> +{
> +	unsigned int clk, best_clk = 0;
> +	unsigned int div, best_div = 0;
> +	unsigned int m, best_m = 0;
> +	unsigned int error;
> +	unsigned int best_err = UINT_MAX;
> +	u64 best_period = 0;
> +
> +	/*
> +	 * The PWM period is determined by:
> +	 *
> +	 *          resolution * pre_div * 2^M
> +	 * period = --------------------------
> +	 *                   refclk
> +	 *
> +	 * With resolution fixed at 2^9 bits, pre_div = {1, 3, 5, 6} and
> +	 * M = [0..7].
> +	 *
> +	 * This allows for periods between 27uS and 384s, as the PWM framework
> +	 * wants a period of equal or lower length than requested, reject
> +	 * anything below 27uS.
> +	 */
> +	if (period <= (u64)NSEC_PER_SEC * LPG_RESOLUTION / 19200000)
> +		return -EINVAL;
> +
> +	/* Limit period to largest possible value, to avoid overflows */
> +	if (period > (u64)NSEC_PER_SEC * LPG_RESOLUTION * 6 * (1 << LPG_MAX_M) / 1024)
> +		period = (u64)NSEC_PER_SEC * LPG_RESOLUTION * 6 * (1 << LPG_MAX_M) / 2014;
> +
> +	/*
> +	 * Search for the pre_div, clk and M by solving the rewritten formula
> +	 * for each clk and pre_div value:
> +	 *
> +	 *                       period * clk
> +	 * M = log2 -------------------------------------
> +	 *           NSEC_PER_SEC * pre_div * resolution
> +	 */
> +	for (clk = 0; clk < ARRAY_SIZE(lpg_clk_rates); clk++) {
> +		u64 nom = period * lpg_clk_rates[clk];
> +
> +		for (div = 0; div < ARRAY_SIZE(lpg_pre_divs); div++) {
> +			u64 denom = (u64)NSEC_PER_SEC * lpg_pre_divs[div] * (1 << 9);
> +			u64 actual;
> +			u64 ratio;
> +
> +			if (nom < denom)
> +				continue;
> +
> +			ratio = div64_u64(nom, denom);
> +			m = ilog2(ratio);
> +			if (m > LPG_MAX_M)
> +				m = LPG_MAX_M;
> +
> +			actual = DIV_ROUND_UP_ULL(denom * (1 << m), lpg_clk_rates[clk]);
> +
> +			error = period - actual;
> +			if (error < best_err) {
> +				best_err = error;
> +
> +				best_div = div;
> +				best_m = m;
> +				best_clk = clk;
> +				best_period = actual;
> +			}
> +		}
> +	}
> +
> +	chan->clk = best_clk;
> +	chan->pre_div = best_div;
> +	chan->pre_div_exp = best_m;
> +	chan->period = best_period;
> +
> +	return 0;
> +}
> +
> +static void lpg_calc_duty(struct lpg_channel *chan, uint64_t duty)
> +{
> +	unsigned int max = LPG_RESOLUTION - 1;
> +	unsigned int val;
> +
> +	val = div64_u64(duty * lpg_clk_rates[chan->clk],
> +			(u64)NSEC_PER_SEC * lpg_pre_divs[chan->pre_div] * (1 << chan->pre_div_exp));
> +
> +	chan->pwm_value = min(val, max);
> +}
> +
> +static void lpg_apply_freq(struct lpg_channel *chan)
> +{
> +	unsigned long val;
> +	struct lpg *lpg = chan->lpg;
> +
> +	if (!chan->enabled)
> +		return;
> +
> +	/* Clock register values are off-by-one from lpg_clk_table */
> +	val = chan->clk + 1;
> +
> +	/* Enable 9bit resolution */
> +	val |= lpg->data->pwm_9bit_mask;
> +
> +	regmap_write(lpg->map, chan->base + LPG_SIZE_CLK_REG, val);
> +
> +	val = chan->pre_div << 5 | chan->pre_div_exp;
> +	regmap_write(lpg->map, chan->base + LPG_PREDIV_CLK_REG, val);
> +}
> +
> +#define LPG_ENABLE_GLITCH_REMOVAL	BIT(5)
> +
> +static void lpg_enable_glitch(struct lpg_channel *chan)
> +{
> +	struct lpg *lpg = chan->lpg;
> +
> +	regmap_update_bits(lpg->map, chan->base + PWM_TYPE_CONFIG_REG,
> +			   LPG_ENABLE_GLITCH_REMOVAL, 0);
> +}
> +
> +static void lpg_disable_glitch(struct lpg_channel *chan)
> +{
> +	struct lpg *lpg = chan->lpg;
> +
> +	regmap_update_bits(lpg->map, chan->base + PWM_TYPE_CONFIG_REG,
> +			   LPG_ENABLE_GLITCH_REMOVAL,
> +			   LPG_ENABLE_GLITCH_REMOVAL);
> +}
> +
> +static void lpg_apply_pwm_value(struct lpg_channel *chan)
> +{
> +	struct lpg *lpg = chan->lpg;
> +	u16 val = chan->pwm_value;
> +
> +	if (!chan->enabled)
> +		return;
> +
> +	regmap_bulk_write(lpg->map, chan->base + PWM_VALUE_REG, &val, sizeof(val));
> +}
> +
> +#define LPG_PATTERN_CONFIG_LO_TO_HI	BIT(4)
> +#define LPG_PATTERN_CONFIG_REPEAT	BIT(3)
> +#define LPG_PATTERN_CONFIG_TOGGLE	BIT(2)
> +#define LPG_PATTERN_CONFIG_PAUSE_HI	BIT(1)
> +#define LPG_PATTERN_CONFIG_PAUSE_LO	BIT(0)
> +
> +static void lpg_apply_lut_control(struct lpg_channel *chan)
> +{
> +	struct lpg *lpg = chan->lpg;
> +	unsigned int hi_pause;
> +	unsigned int lo_pause;
> +	unsigned int conf = 0;
> +	unsigned int step = chan->ramp_tick_ms;
> +	unsigned int lo_idx = chan->pattern_lo_idx;
> +	unsigned int hi_idx = chan->pattern_hi_idx;
> +
> +	if (!chan->ramp_enabled || chan->pattern_lo_idx == chan->pattern_hi_idx)
> +		return;
> +
> +	hi_pause = DIV_ROUND_UP(chan->ramp_hi_pause_ms, step);
> +	lo_pause = DIV_ROUND_UP(chan->ramp_lo_pause_ms, step);
> +
> +	if (!chan->ramp_reverse)
> +		conf |= LPG_PATTERN_CONFIG_LO_TO_HI;
> +	if (!chan->ramp_oneshot)
> +		conf |= LPG_PATTERN_CONFIG_REPEAT;
> +	if (chan->ramp_ping_pong)
> +		conf |= LPG_PATTERN_CONFIG_TOGGLE;
> +	if (chan->ramp_hi_pause_ms)
> +		conf |= LPG_PATTERN_CONFIG_PAUSE_HI;
> +	if (chan->ramp_lo_pause_ms)
> +		conf |= LPG_PATTERN_CONFIG_PAUSE_LO;
> +
> +	regmap_write(lpg->map, chan->base + LPG_PATTERN_CONFIG_REG, conf);
> +	regmap_write(lpg->map, chan->base + LPG_HI_IDX_REG, hi_idx);
> +	regmap_write(lpg->map, chan->base + LPG_LO_IDX_REG, lo_idx);
> +
> +	regmap_write(lpg->map, chan->base + LPG_RAMP_DURATION_REG, step);
> +	regmap_write(lpg->map, chan->base + LPG_HI_PAUSE_REG, hi_pause);
> +	regmap_write(lpg->map, chan->base + LPG_LO_PAUSE_REG, lo_pause);
> +}
> +
> +#define LPG_ENABLE_CONTROL_OUTPUT		BIT(7)
> +#define LPG_ENABLE_CONTROL_BUFFER_TRISTATE	BIT(5)
> +#define LPG_ENABLE_CONTROL_SRC_PWM		BIT(2)
> +#define LPG_ENABLE_CONTROL_RAMP_GEN		BIT(1)
> +
> +static void lpg_apply_control(struct lpg_channel *chan)
> +{
> +	unsigned int ctrl;
> +	struct lpg *lpg = chan->lpg;
> +
> +	ctrl = LPG_ENABLE_CONTROL_BUFFER_TRISTATE;
> +
> +	if (chan->enabled)
> +		ctrl |= LPG_ENABLE_CONTROL_OUTPUT;
> +
> +	if (chan->pattern_lo_idx != chan->pattern_hi_idx)
> +		ctrl |= LPG_ENABLE_CONTROL_RAMP_GEN;
> +	else
> +		ctrl |= LPG_ENABLE_CONTROL_SRC_PWM;
> +
> +	regmap_write(lpg->map, chan->base + PWM_ENABLE_CONTROL_REG, ctrl);
> +
> +	/*
> +	 * Due to LPG hardware bug, in the PWM mode, having enabled PWM,
> +	 * We have to write PWM values one more time.
> +	 */
> +	if (chan->enabled)
> +		lpg_apply_pwm_value(chan);
> +}
> +
> +#define LPG_SYNC_PWM	BIT(0)
> +
> +static void lpg_apply_sync(struct lpg_channel *chan)
> +{
> +	struct lpg *lpg = chan->lpg;
> +
> +	regmap_write(lpg->map, chan->base + PWM_SYNC_REG, LPG_SYNC_PWM);
> +}
> +
> +static int lpg_parse_dtest(struct lpg *lpg)
> +{
> +	struct lpg_channel *chan;
> +	struct device_node *np = lpg->dev->of_node;
> +	int count;
> +	int ret;
> +	int i;
> +
> +	count = of_property_count_u32_elems(np, "qcom,dtest");
> +	if (count == -EINVAL) {
> +		return 0;
> +	} else if (count < 0) {
> +		ret = count;
> +		goto err_malformed;
> +	} else if (count != lpg->data->num_channels * 2) {
> +		dev_err(lpg->dev, "qcom,dtest needs to be %d items\n",
> +			lpg->data->num_channels * 2);
> +		return -EINVAL;
> +	}
> +
> +	for (i = 0; i < lpg->data->num_channels; i++) {
> +		chan = &lpg->channels[i];
> +
> +		ret = of_property_read_u32_index(np, "qcom,dtest", i * 2,
> +						 &chan->dtest_line);
> +		if (ret)
> +			goto err_malformed;
> +
> +		ret = of_property_read_u32_index(np, "qcom,dtest", i * 2 + 1,
> +						 &chan->dtest_value);
> +		if (ret)
> +			goto err_malformed;
> +	}
> +
> +	return 0;
> +
> +err_malformed:
> +	dev_err(lpg->dev, "malformed qcom,dtest\n");
> +	return ret;
> +}
> +
> +static void lpg_apply_dtest(struct lpg_channel *chan)
> +{
> +	struct lpg *lpg = chan->lpg;
> +
> +	if (!chan->dtest_line)
> +		return;
> +
> +	regmap_write(lpg->map, chan->base + PWM_SEC_ACCESS_REG, 0xa5);
> +	regmap_write(lpg->map, chan->base + PWM_DTEST_REG(chan->dtest_line),
> +		     chan->dtest_value);
> +}
> +
> +static void lpg_apply(struct lpg_channel *chan)
> +{
> +	lpg_disable_glitch(chan);
> +	lpg_apply_freq(chan);
> +	lpg_apply_pwm_value(chan);
> +	lpg_apply_control(chan);
> +	lpg_apply_sync(chan);
> +	lpg_apply_lut_control(chan);
> +	lpg_enable_glitch(chan);
> +}
> +
> +static void lpg_brightness_set(struct lpg_led *led, struct led_classdev *cdev,
> +			       struct mc_subled *subleds)
> +{
> +	enum led_brightness brightness;
> +	struct lpg_channel *chan;
> +	unsigned int triled_enabled = 0;
> +	unsigned int triled_mask = 0;
> +	unsigned int lut_mask = 0;
> +	unsigned int duty;
> +	struct lpg *lpg = led->lpg;
> +	int i;
> +
> +	for (i = 0; i < led->num_channels; i++) {
> +		chan = led->channels[i];
> +		brightness = subleds[i].brightness;
> +
> +		if (brightness == LED_OFF) {
> +			chan->enabled = false;
> +			chan->ramp_enabled = false;
> +		} else if (chan->pattern_lo_idx != chan->pattern_hi_idx) {
> +			lpg_calc_freq(chan, NSEC_PER_MSEC);
> +
> +			chan->enabled = true;
> +			chan->ramp_enabled = true;
> +
> +			lut_mask |= chan->lut_mask;
> +			triled_enabled |= chan->triled_mask;
> +		} else {
> +			lpg_calc_freq(chan, NSEC_PER_MSEC);
> +
> +			duty = div_u64(brightness * chan->period, cdev->max_brightness);
> +			lpg_calc_duty(chan, duty);
> +			chan->enabled = true;
> +			chan->ramp_enabled = false;
> +
> +			triled_enabled |= chan->triled_mask;
> +		}
> +
> +		triled_mask |= chan->triled_mask;
> +
> +		lpg_apply(chan);
> +	}
> +
> +	/* Toggle triled lines */
> +	if (triled_mask)
> +		triled_set(lpg, triled_mask, triled_enabled);
> +
> +	/* Trigger start of ramp generator(s) */
> +	if (lut_mask)
> +		lpg_lut_sync(lpg, lut_mask);
> +}
> +
> +static void lpg_brightness_single_set(struct led_classdev *cdev,
> +				      enum led_brightness value)
> +{
> +	struct lpg_led *led = container_of(cdev, struct lpg_led, cdev);
> +	struct mc_subled info;
> +
> +	info.brightness = value;
> +	lpg_brightness_set(led, cdev, &info);
> +}
> +
> +static void lpg_brightness_mc_set(struct led_classdev *cdev,
> +				  enum led_brightness value)
> +{
> +	struct led_classdev_mc *mc = lcdev_to_mccdev(cdev);
> +	struct lpg_led *led = container_of(mc, struct lpg_led, mcdev);
> +
> +	led_mc_calc_color_components(mc, value);
> +	lpg_brightness_set(led, cdev, mc->subled_info);
> +}
> +
> +static int lpg_blink_set(struct lpg_led *led,
> +			 unsigned long *delay_on, unsigned long *delay_off)
> +{
> +	struct lpg_channel *chan;
> +	unsigned int period;
> +	unsigned int triled_mask = 0;
> +	struct lpg *lpg = led->lpg;
> +	u64 duty;
> +	int i;
> +
> +	if (!*delay_on && !*delay_off) {
> +		*delay_on = 500;
> +		*delay_off = 500;
> +	}
> +
> +	duty = *delay_on * NSEC_PER_MSEC;
> +	period = (*delay_on + *delay_off) * NSEC_PER_MSEC;
> +
> +	for (i = 0; i < led->num_channels; i++) {
> +		chan = led->channels[i];
> +
> +		lpg_calc_freq(chan, period);
> +		lpg_calc_duty(chan, duty);
> +
> +		chan->enabled = true;
> +		chan->ramp_enabled = false;
> +
> +		triled_mask |= chan->triled_mask;
> +
> +		lpg_apply(chan);
> +	}
> +
> +	/* Enable triled lines */
> +	triled_set(lpg, triled_mask, triled_mask);
> +
> +	chan = led->channels[0];
> +	duty = div_u64(chan->pwm_value * chan->period, LPG_RESOLUTION);
> +	*delay_on = div_u64(duty, NSEC_PER_MSEC);
> +	*delay_off = div_u64(chan->period - duty, NSEC_PER_MSEC);
> +
> +	return 0;
> +}
> +
> +static int lpg_blink_single_set(struct led_classdev *cdev,
> +				unsigned long *delay_on, unsigned long *delay_off)
> +{
> +	struct lpg_led *led = container_of(cdev, struct lpg_led, cdev);
> +
> +	return lpg_blink_set(led, delay_on, delay_off);
> +}
> +
> +static int lpg_blink_mc_set(struct led_classdev *cdev,
> +			    unsigned long *delay_on, unsigned long *delay_off)
> +{
> +	struct led_classdev_mc *mc = lcdev_to_mccdev(cdev);
> +	struct lpg_led *led = container_of(mc, struct lpg_led, mcdev);
> +
> +	return lpg_blink_set(led, delay_on, delay_off);
> +}
> +
> +static int lpg_pattern_set(struct lpg_led *led, struct led_pattern *pattern,
> +			   u32 len, int repeat)
> +{
> +	struct lpg_channel *chan;
> +	struct lpg *lpg = led->lpg;
> +	unsigned int hi_pause;
> +	unsigned int lo_pause;
> +	unsigned int lo_idx;
> +	unsigned int hi_idx;
> +	bool ping_pong = true;
> +	int brightness_a;
> +	int brightness_b;
> +	int ret;
> +	int i;
> +
> +	/* Only support oneshot or indefinite loops, due to limited pattern space */
> +	if (repeat != -1 && repeat != 1)
> +		return -EINVAL;
> +
> +	/*
> +	 * The LPG plays patterns with at a fixed pace, a "low pause" can be
> +	 * performed before the pattern and a "high pause" after. In order to
> +	 * save space the pattern can be played in "ping pong" mode, in which
> +	 * the pattern is first played forward, then "high pause" is applied,
> +	 * then the pattern is played backwards and finally the "low pause" is
> +	 * applied.
> +	 *
> +	 * The delta_t of the first entry is used to determine the pace of the
> +	 * pattern.
> +	 *
> +	 * If the specified pattern is a palindrome the ping pong mode is
> +	 * enabled. In this scenario the delta_t of the last entry determines
> +	 * the "low pause" time and the delta_t of the middle entry (i.e. the
> +	 * last in the programmed pattern) determines the "high pause". If the
> +	 * pattern consists of an odd number of values, no "high pause" is
> +	 * used.
> +	 *
> +	 * When ping pong mode is not selected, the delta_t of the last entry
> +	 * is used as "high pause". No "low pause" is used.
> +	 *
> +	 * delta_t of any other members of the pattern is ignored.
> +	 */
> +
> +	/* Detect palindromes and use "ping pong" to reduce LUT usage */
> +	for (i = 0; i < len / 2; i++) {
> +		brightness_a = pattern[i].brightness;
> +		brightness_b = pattern[len - i - 1].brightness;
> +
> +		if (brightness_a != brightness_b) {
> +			ping_pong = false;
> +			break;
> +		}
> +	}
> +
> +	if (ping_pong) {
> +		if (len % 2)
> +			hi_pause = 0;
> +		else
> +			hi_pause = pattern[(len + 1) / 2].delta_t;
> +		lo_pause = pattern[len - 1].delta_t;
> +
> +		len = (len + 1) / 2;
> +	} else {
> +		hi_pause = pattern[len - 1].delta_t;
> +		lo_pause = 0;
> +	}
> +
> +	ret = lpg_lut_store(lpg, pattern, len, &lo_idx, &hi_idx);
> +	if (ret < 0)
> +		return ret;
> +
> +	for (i = 0; i < led->num_channels; i++) {
> +		chan = led->channels[i];
> +
> +		chan->ramp_tick_ms = pattern[0].delta_t;
> +		chan->ramp_ping_pong = ping_pong;
> +		chan->ramp_oneshot = repeat != -1;
> +
> +		chan->ramp_lo_pause_ms = lo_pause;
> +		chan->ramp_hi_pause_ms = hi_pause;
> +
> +		chan->pattern_lo_idx = lo_idx;
> +		chan->pattern_hi_idx = hi_idx;
> +	}
> +
> +	return 0;
> +}
> +
> +static int lpg_pattern_single_set(struct led_classdev *cdev,
> +				  struct led_pattern *pattern, u32 len,
> +				  int repeat)
> +{
> +	struct lpg_led *led = container_of(cdev, struct lpg_led, cdev);
> +	int ret;
> +
> +	ret = lpg_pattern_set(led, pattern, len, repeat);
> +	if (ret < 0)
> +		return ret;
> +
> +	lpg_brightness_single_set(cdev, LED_FULL);
> +
> +	return 0;
> +}
> +
> +static int lpg_pattern_mc_set(struct led_classdev *cdev,
> +			      struct led_pattern *pattern, u32 len,
> +			      int repeat)
> +{
> +	struct led_classdev_mc *mc = lcdev_to_mccdev(cdev);
> +	struct lpg_led *led = container_of(mc, struct lpg_led, mcdev);
> +	int ret;
> +
> +	ret = lpg_pattern_set(led, pattern, len, repeat);
> +	if (ret < 0)
> +		return ret;
> +
> +	led_mc_calc_color_components(mc, LED_FULL);
> +	lpg_brightness_set(led, cdev, mc->subled_info);
> +
> +	return 0;
> +}
> +
> +static int lpg_pattern_clear(struct lpg_led *led)
> +{
> +	struct lpg_channel *chan;
> +	struct lpg *lpg = led->lpg;
> +	int i;
> +
> +	chan = led->channels[0];
> +	lpg_lut_free(lpg, chan->pattern_lo_idx, chan->pattern_hi_idx);
> +
> +	for (i = 0; i < led->num_channels; i++) {
> +		chan = led->channels[i];
> +		chan->pattern_lo_idx = 0;
> +		chan->pattern_hi_idx = 0;
> +	}
> +
> +	return 0;
> +}
> +
> +static int lpg_pattern_single_clear(struct led_classdev *cdev)
> +{
> +	struct lpg_led *led = container_of(cdev, struct lpg_led, cdev);
> +
> +	return lpg_pattern_clear(led);
> +}
> +
> +static int lpg_pattern_mc_clear(struct led_classdev *cdev)
> +{
> +	struct led_classdev_mc *mc = lcdev_to_mccdev(cdev);
> +	struct lpg_led *led = container_of(mc, struct lpg_led, mcdev);
> +
> +	return lpg_pattern_clear(led);
> +}
> +
> +static int lpg_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
> +{
> +	struct lpg *lpg = container_of(chip, struct lpg, pwm);
> +	struct lpg_channel *chan = &lpg->channels[pwm->hwpwm];
> +
> +	return chan->in_use ? -EBUSY : 0;
> +}
> +
> +/*
> + * Limitations:
> + * - Updating both duty and period is not done atomically, so the output signal
> + *   will momentarily be a mix of the settings.
> + */
> +static int lpg_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
> +			 const struct pwm_state *state)
> +{
> +	struct lpg *lpg = container_of(chip, struct lpg, pwm);
> +	struct lpg_channel *chan = &lpg->channels[pwm->hwpwm];
> +	int ret;
> +
> +	if (state->polarity != PWM_POLARITY_NORMAL)
> +		return -EINVAL;
> +
> +	ret = lpg_calc_freq(chan, state->period);
> +	if (ret < 0)
> +		return ret;
> +
> +	lpg_calc_duty(chan, state->duty_cycle);
> +	chan->enabled = state->enabled;
> +
> +	lpg_apply(chan);
> +
> +	triled_set(lpg, chan->triled_mask, chan->enabled ? chan->triled_mask : 0);
> +
> +	return 0;
> +}
> +
> +static void lpg_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
> +			      struct pwm_state *state)
> +{
> +	struct lpg *lpg = container_of(chip, struct lpg, pwm);
> +	struct lpg_channel *chan = &lpg->channels[pwm->hwpwm];
> +	u64 duty = DIV_ROUND_UP_ULL(chan->pwm_value * chan->period, LPG_RESOLUTION - 1);
> +
> +	state->period = chan->period;
> +	state->duty_cycle = duty;
> +	state->polarity = PWM_POLARITY_NORMAL;
> +	state->enabled = chan->enabled;
> +}
> +
> +static const struct pwm_ops lpg_pwm_ops = {
> +	.request = lpg_pwm_request,
> +	.apply = lpg_pwm_apply,
> +	.get_state = lpg_pwm_get_state,
> +	.owner = THIS_MODULE,
> +};
> +
> +static int lpg_add_pwm(struct lpg *lpg)
> +{
> +	int ret;
> +
> +	lpg->pwm.base = -1;
> +	lpg->pwm.dev = lpg->dev;
> +	lpg->pwm.npwm = lpg->num_channels;
> +	lpg->pwm.ops = &lpg_pwm_ops;
> +
> +	ret = pwmchip_add(&lpg->pwm);
> +	if (ret)
> +		dev_err(lpg->dev, "failed to add PWM chip: ret %d\n", ret);
> +
> +	return ret;
> +}
> +
> +static int lpg_parse_channel(struct lpg *lpg, struct device_node *np,
> +			     struct lpg_channel **channel)
> +{
> +	struct lpg_channel *chan;
> +	u32 color = LED_COLOR_ID_GREEN;
> +	u32 reg;
> +	int ret;
> +
> +	ret = of_property_read_u32(np, "reg", &reg);
> +	if (ret || !reg || reg > lpg->num_channels) {
> +		dev_err(lpg->dev, "invalid \"reg\" of %pOFn\n", np);
> +		return -EINVAL;
> +	}
> +
> +	chan = &lpg->channels[reg - 1];
> +	chan->in_use = true;
> +
> +	ret = of_property_read_u32(np, "color", &color);
> +	if (ret < 0 && ret != -EINVAL) {
> +		dev_err(lpg->dev, "failed to parse \"color\" of %pOF\n", np);
> +		return ret;
> +	}
> +
> +	chan->color = color;
> +
> +	*channel = chan;
> +
> +	return 0;
> +}
> +
> +static int lpg_add_led(struct lpg *lpg, struct device_node *np)
> +{
> +	struct led_init_data init_data = {};
> +	struct led_classdev *cdev;
> +	struct device_node *child;
> +	struct mc_subled *info;
> +	struct lpg_led *led;
> +	const char *state;
> +	int num_channels;
> +	u32 color = 0;
> +	int ret;
> +	int i;
> +
> +	ret = of_property_read_u32(np, "color", &color);
> +	if (ret < 0 && ret != -EINVAL) {
> +		dev_err(lpg->dev, "failed to parse \"color\" of %pOF\n", np);
> +		return ret;
> +	}
> +
> +	if (color == LED_COLOR_ID_RGB)
> +		num_channels = of_get_available_child_count(np);
> +	else
> +		num_channels = 1;
> +
> +	led = devm_kzalloc(lpg->dev, struct_size(led, channels, num_channels), GFP_KERNEL);
> +	if (!led)
> +		return -ENOMEM;
> +
> +	led->lpg = lpg;
> +	led->num_channels = num_channels;
> +
> +	if (color == LED_COLOR_ID_RGB) {
> +		info = devm_kcalloc(lpg->dev, num_channels, sizeof(*info), GFP_KERNEL);
> +		if (!info)
> +			return -ENOMEM;
> +		i = 0;
> +		for_each_available_child_of_node(np, child) {
> +			ret = lpg_parse_channel(lpg, child, &led->channels[i]);
> +			if (ret < 0)
> +				return ret;
> +
> +			info[i].color_index = led->channels[i]->color;
> +			info[i].intensity = LED_FULL;
> +			i++;
> +		}
> +
> +		led->mcdev.subled_info = info;
> +		led->mcdev.num_colors = num_channels;
> +
> +		cdev = &led->mcdev.led_cdev;
> +		cdev->brightness_set = lpg_brightness_mc_set;
> +		cdev->blink_set = lpg_blink_mc_set;
> +
> +		/* Register pattern accessors only if we have a LUT block */
> +		if (lpg->lut_base) {
> +			cdev->pattern_set = lpg_pattern_mc_set;
> +			cdev->pattern_clear = lpg_pattern_mc_clear;
> +		}
> +	} else {
> +		ret = lpg_parse_channel(lpg, np, &led->channels[0]);
> +		if (ret < 0)
> +			return ret;
> +
> +		cdev = &led->cdev;
> +		cdev->brightness_set = lpg_brightness_single_set;
> +		cdev->blink_set = lpg_blink_single_set;
> +
> +		/* Register pattern accessors only if we have a LUT block */
> +		if (lpg->lut_base) {
> +			cdev->pattern_set = lpg_pattern_single_set;
> +			cdev->pattern_clear = lpg_pattern_single_clear;
> +		}
> +	}
> +
> +	cdev->default_trigger = of_get_property(np, "linux,default-trigger", NULL);
> +	cdev->max_brightness = 255;
> +
> +	if (!of_property_read_string(np, "default-state", &state) &&
> +	    !strcmp(state, "on"))
> +		cdev->brightness = LED_FULL;
> +	else
> +		cdev->brightness = LED_OFF;
> +
> +	cdev->brightness_set(cdev, cdev->brightness);
> +
> +	init_data.fwnode = of_fwnode_handle(np);
> +
> +	if (color == LED_COLOR_ID_RGB)
> +		ret = devm_led_classdev_multicolor_register_ext(lpg->dev, &led->mcdev, &init_data);
> +	else
> +		ret = devm_led_classdev_register_ext(lpg->dev, &led->cdev, &init_data);
> +	if (ret)
> +		dev_err(lpg->dev, "unable to register %s\n", cdev->name);
> +
> +	return ret;
> +}
> +
> +static int lpg_init_channels(struct lpg *lpg)
> +{
> +	const struct lpg_data *data = lpg->data;
> +	int i;
> +
> +	lpg->num_channels = data->num_channels;
> +	lpg->channels = devm_kcalloc(lpg->dev, data->num_channels,
> +				     sizeof(struct lpg_channel), GFP_KERNEL);
> +	if (!lpg->channels)
> +		return -ENOMEM;
> +
> +	for (i = 0; i < data->num_channels; i++) {
> +		lpg->channels[i].lpg = lpg;
> +		lpg->channels[i].base = data->channels[i].base;
> +		lpg->channels[i].triled_mask = data->channels[i].triled_mask;
> +		lpg->channels[i].lut_mask = BIT(i);
> +	}
> +
> +	return 0;
> +}
> +
> +static int lpg_init_triled(struct lpg *lpg)
> +{
> +	struct device_node *np = lpg->dev->of_node;
> +	int ret;
> +
> +	/* Skip initialization if we don't have a triled block */
> +	if (!lpg->data->triled_base)
> +		return 0;
> +
> +	lpg->triled_base = lpg->data->triled_base;
> +	lpg->triled_has_atc_ctl = lpg->data->triled_has_atc_ctl;
> +	lpg->triled_has_src_sel = lpg->data->triled_has_src_sel;
> +
> +	if (lpg->triled_has_src_sel) {
> +		ret = of_property_read_u32(np, "qcom,power-source", &lpg->triled_src);
> +		if (ret || lpg->triled_src == 2 || lpg->triled_src > 3) {
> +			dev_err(lpg->dev, "invalid power source\n");
> +			return -EINVAL;
> +		}
> +	}
> +
> +	/* Disable automatic trickle charge LED */
> +	if (lpg->triled_has_atc_ctl)
> +		regmap_write(lpg->map, lpg->triled_base + TRI_LED_ATC_CTL, 0);
> +
> +	/* Configure power source */
> +	if (lpg->triled_has_src_sel)
> +		regmap_write(lpg->map, lpg->triled_base + TRI_LED_SRC_SEL, lpg->triled_src);
> +
> +	/* Default all outputs to off */
> +	regmap_write(lpg->map, lpg->triled_base + TRI_LED_EN_CTL, 0);
> +
> +	return 0;
> +}
> +
> +static int lpg_init_lut(struct lpg *lpg)
> +{
> +	const struct lpg_data *data = lpg->data;
> +	size_t bitmap_size;
> +
> +	if (!data->lut_base)
> +		return 0;
> +
> +	lpg->lut_base = data->lut_base;
> +	lpg->lut_size = data->lut_size;
> +
> +	bitmap_size = BITS_TO_BYTES(lpg->lut_size);
> +	lpg->lut_bitmap = devm_kzalloc(lpg->dev, bitmap_size, GFP_KERNEL);
> +	if (!lpg->lut_bitmap)
> +		return -ENOMEM;
> +
> +	return 0;
> +}
> +
> +static int lpg_probe(struct platform_device *pdev)
> +{
> +	struct device_node *np;
> +	struct lpg *lpg;
> +	int ret;
> +	int i;
> +
> +	lpg = devm_kzalloc(&pdev->dev, sizeof(*lpg), GFP_KERNEL);
> +	if (!lpg)
> +		return -ENOMEM;
> +
> +	lpg->data = of_device_get_match_data(&pdev->dev);
> +	if (!lpg->data)
> +		return -EINVAL;
> +
> +	platform_set_drvdata(pdev, lpg);
> +
> +	lpg->dev = &pdev->dev;
> +
> +	lpg->map = dev_get_regmap(pdev->dev.parent, NULL);
> +	if (!lpg->map) {
> +		dev_err(&pdev->dev, "parent regmap unavailable\n");
> +		return -ENXIO;
> +	}
> +
> +	ret = lpg_init_channels(lpg);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = lpg_parse_dtest(lpg);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = lpg_init_triled(lpg);
> +	if (ret < 0)
> +		return ret;
> +
> +	ret = lpg_init_lut(lpg);
> +	if (ret < 0)
> +		return ret;
> +
> +	for_each_available_child_of_node(pdev->dev.of_node, np) {
> +		ret = lpg_add_led(lpg, np);
> +		if (ret)
> +			return ret;
> +	}
> +
> +	for (i = 0; i < lpg->num_channels; i++)
> +		lpg_apply_dtest(&lpg->channels[i]);
> +
> +	return lpg_add_pwm(lpg);
> +}
> +
> +static int lpg_remove(struct platform_device *pdev)
> +{
> +	struct lpg *lpg = platform_get_drvdata(pdev);
> +
> +	pwmchip_remove(&lpg->pwm);
> +
> +	return 0;
> +}
> +
> +static const struct lpg_data pm8916_pwm_data = {
> +	.pwm_9bit_mask = BIT(2),
> +
> +	.num_channels = 1,
> +	.channels = (const struct lpg_channel_data[]) {
> +		{ .base = 0xbc00 },
> +	},
> +};
> +
> +static const struct lpg_data pm8941_lpg_data = {
> +	.lut_base = 0xb000,
> +	.lut_size = 64,
> +
> +	.triled_base = 0xd000,
> +	.triled_has_atc_ctl = true,
> +	.triled_has_src_sel = true,
> +
> +	.pwm_9bit_mask = 3 << 4,
> +
> +	.num_channels = 8,
> +	.channels = (const struct lpg_channel_data[]) {
> +		{ .base = 0xb100 },
> +		{ .base = 0xb200 },
> +		{ .base = 0xb300 },
> +		{ .base = 0xb400 },
> +		{ .base = 0xb500, .triled_mask = BIT(5) },
> +		{ .base = 0xb600, .triled_mask = BIT(6) },
> +		{ .base = 0xb700, .triled_mask = BIT(7) },
> +		{ .base = 0xb800 },
> +	},
> +};
> +
> +static const struct lpg_data pm8994_lpg_data = {
> +	.lut_base = 0xb000,
> +	.lut_size = 64,
> +
> +	.pwm_9bit_mask = 3 << 4,
> +
> +	.num_channels = 6,
> +	.channels = (const struct lpg_channel_data[]) {
> +		{ .base = 0xb100 },
> +		{ .base = 0xb200 },
> +		{ .base = 0xb300 },
> +		{ .base = 0xb400 },
> +		{ .base = 0xb500 },
> +		{ .base = 0xb600 },
> +	},
> +};
> +
> +static const struct lpg_data pmi8994_lpg_data = {
> +	.lut_base = 0xb000,
> +	.lut_size = 24,
> +
> +	.triled_base = 0xd000,
> +	.triled_has_atc_ctl = true,
> +	.triled_has_src_sel = true,
> +
> +	.pwm_9bit_mask = BIT(4),
> +
> +	.num_channels = 4,
> +	.channels = (const struct lpg_channel_data[]) {
> +		{ .base = 0xb100, .triled_mask = BIT(5) },
> +		{ .base = 0xb200, .triled_mask = BIT(6) },
> +		{ .base = 0xb300, .triled_mask = BIT(7) },
> +		{ .base = 0xb400 },
> +	},
> +};
> +
> +static const struct lpg_data pmi8998_lpg_data = {
> +	.lut_base = 0xb000,
> +	.lut_size = 49,
> +
> +	.triled_base = 0xd000,
> +
> +	.pwm_9bit_mask = BIT(4),
> +
> +	.num_channels = 6,
> +	.channels = (const struct lpg_channel_data[]) {
> +		{ .base = 0xb100 },
> +		{ .base = 0xb200 },
> +		{ .base = 0xb300, .triled_mask = BIT(5) },
> +		{ .base = 0xb400, .triled_mask = BIT(6) },
> +		{ .base = 0xb500, .triled_mask = BIT(7) },
> +		{ .base = 0xb600 },
> +	},
> +};
> +
> +static const struct lpg_data pm8150b_lpg_data = {
> +	.lut_base = 0xb000,
> +	.lut_size = 24,
> +
> +	.triled_base = 0xd000,
> +
> +	.pwm_9bit_mask = BIT(4),
> +
> +	.num_channels = 2,
> +	.channels = (const struct lpg_channel_data[]) {
> +		{ .base = 0xb100, .triled_mask = BIT(7) },
> +		{ .base = 0xb200, .triled_mask = BIT(6) },
> +	},
> +};
> +
> +static const struct lpg_data pm8150l_lpg_data = {
> +	.lut_base = 0xb000,
> +	.lut_size = 48,
> +
> +	.triled_base = 0xd000,
> +
> +	.pwm_9bit_mask = BIT(4),
> +
> +	.num_channels = 5,
> +	.channels = (const struct lpg_channel_data[]) {
> +		{ .base = 0xb100, .triled_mask = BIT(7) },
> +		{ .base = 0xb200, .triled_mask = BIT(6) },
> +		{ .base = 0xb300, .triled_mask = BIT(5) },
> +		{ .base = 0xbc00 },
> +		{ .base = 0xbd00 },
> +
> +	},
> +};
> +
> +static const struct of_device_id lpg_of_table[] = {
> +	{ .compatible = "qcom,pm8150b-lpg", .data = &pm8150b_lpg_data },
> +	{ .compatible = "qcom,pm8150l-lpg", .data = &pm8150l_lpg_data },
> +	{ .compatible = "qcom,pm8916-pwm", .data = &pm8916_pwm_data },
> +	{ .compatible = "qcom,pm8941-lpg", .data = &pm8941_lpg_data },
> +	{ .compatible = "qcom,pm8994-lpg", .data = &pm8994_lpg_data },
> +	{ .compatible = "qcom,pmi8994-lpg", .data = &pmi8994_lpg_data },
> +	{ .compatible = "qcom,pmi8998-lpg", .data = &pmi8998_lpg_data },
> +	{ .compatible = "qcom,pmc8180c-lpg", .data = &pm8150l_lpg_data },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, lpg_of_table);
> +
> +static struct platform_driver lpg_driver = {
> +	.probe = lpg_probe,
> +	.remove = lpg_remove,
> +	.driver = {
> +		.name = "qcom-spmi-lpg",
> +		.of_match_table = lpg_of_table,
> +	},
> +};
> +module_platform_driver(lpg_driver);
> +
> +MODULE_DESCRIPTION("Qualcomm LPG LED driver");
> +MODULE_LICENSE("GPL v2");
> -- 
> 2.29.2
>