Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
From:   Aswath Govindraju <a-govindraju@ti.com>
CC:     <linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
        Rob Herring <robh+dt@kernel.org>,
        Tero Kristo <kristo@kernel.org>,
        Vignesh Raghavendra <vigneshr@ti.com>,
        Nishanth Menon <nm@ti.com>,
        Aswath Govindraju <a-govindraju@ti.com>
Subject: [PATCH 5/6] arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support
Date:   Tue, 25 Jan 2022 18:41:12 +0530
Message-ID: <20220125131113.727-6-a-govindraju@ti.com>
In-Reply-To: <20220125131113.727-1-a-govindraju@ti.com>
References: <20220125131113.727-1-a-govindraju@ti.com>
MIME-Version: 1.0
Content-Type: text/plain
To:     unlisted-recipients:; (no To-header on input)
Precedence: bulk

The board uses lane 1 of SERDES for USB. Set the mux
accordingly.

The USB controller and EVM supports super-speed for USB0
on the Type-C port. However, the SERDES has a limitation
that upto 2 protocols can be used at a time. The SERDES is
wired for PCIe, eDP and USB super-speed. It has been
chosen to use PCIe and eDP as default. So restrict
USB0 to high-speed mode.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index 791f235bd95f..aa75dc541842 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -147,6 +147,12 @@
 			J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */
 		>;
 	};
+
+	main_usbss0_pins_default: main-usbss0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
+		>;
+	};
 };
 
 &wkup_pmx0 {
@@ -372,6 +378,22 @@
 	};
 };
 
+&usb_serdes_mux {
+	idle-states = <1>; /* USB0 to SERDES lane 1 */
+};
+
+&usbss0 {
+	pinctrl-0 = <&main_usbss0_pins_default>;
+	pinctrl-names = "default";
+	ti,vbus-divider;
+	ti,usb2-only;
+};
+
+&usb0 {
+	dr_mode = "otg";
+	maximum-speed = "high-speed";
+};
+
 &mcu_mcan0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_mcan0_pins_default>;
-- 
2.17.1