Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Wesley Cheng <quic_wcheng@quicinc.com>
To:     <balbi@kernel.org>, <gregkh@linuxfoundation.org>
CC:     <linux-usb@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
        <quic_jackp@quicinc.com>, <Thinh.Nguyen@synopsys.com>,
        Wesley Cheng <quic_wcheng@quicinc.com>
Subject: [RFC PATCH 1/3] usb: dwc3: Flush pending SETUP data during stop active xfers
Date:   Thu, 3 Feb 2022 00:00:15 -0800
Message-ID: <20220203080017.27339-2-quic_wcheng@quicinc.com>
In-Reply-To: <20220203080017.27339-1-quic_wcheng@quicinc.com>
References: <20220203080017.27339-1-quic_wcheng@quicinc.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Content-Type: text/plain
Precedence: bulk

While running the pullup disable sequence, if there are pending SETUP
transfers stored in the controller, then the endxfer commands will
fail w/ ETIMEDOUT.  As a suggestion from SNPS, in order to drain the
SETUP packets, SW needs to issue a STARTXFER command.  After issuing
the STARTXFER, and retrying the ENDXFER, the command should succeed.
Else, if the endpoints are not properly stopped, the controller halt
sequence will fail as well.

One limitation is that the current logic will drop the SETUP data
being received (ie dropping the SETUP packet), however, it should be
acceptable in the pullup disable case, as the device is eventually
going to disconnect from the host.

Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
---
 drivers/usb/dwc3/core.h   |  7 +++++++
 drivers/usb/dwc3/ep0.c    | 21 ++++++++++++--------
 drivers/usb/dwc3/gadget.c | 42 ++++++++++++++++++++++++++++++++++-----
 3 files changed, 57 insertions(+), 13 deletions(-)

diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index e1cc3f7398fb..a124694c0038 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -1546,6 +1546,8 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
 int dwc3_send_gadget_generic_command(struct dwc3 *dwc, unsigned int cmd,
 		u32 param);
 void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc);
+void dwc3_ep0_stall_and_restart(struct dwc3 *dwc);
+void dwc3_ep0_end_control_data(struct dwc3 *dwc, struct dwc3_ep *dep);
 #else
 static inline int dwc3_gadget_init(struct dwc3 *dwc)
 { return 0; }
@@ -1567,6 +1569,11 @@ static inline int dwc3_send_gadget_generic_command(struct dwc3 *dwc,
 { return 0; }
 static inline void dwc3_gadget_clear_tx_fifos(struct dwc3 *dwc)
 { }
+static inline void dwc3_ep0_stall_and_restart(struct dwc3 *dwc)
+{ }
+static inline void dwc3_ep0_end_control_data(struct dwc3 *dwc,
+					     struct dwc3_ep *dep)
+{ }
 #endif
 
 #if IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c
index 658739410992..eb677b888610 100644
--- a/drivers/usb/dwc3/ep0.c
+++ b/drivers/usb/dwc3/ep0.c
@@ -197,7 +197,7 @@ int dwc3_gadget_ep0_queue(struct usb_ep *ep, struct usb_request *request,
 	int				ret;
 
 	spin_lock_irqsave(&dwc->lock, flags);
-	if (!dep->endpoint.desc || !dwc->pullups_connected) {
+	if (!dep->endpoint.desc || !dwc->pullups_connected || !dwc->connected) {
 		dev_err(dwc->dev, "%s: can't queue to disabled endpoint\n",
 				dep->name);
 		ret = -ESHUTDOWN;
@@ -218,19 +218,21 @@ int dwc3_gadget_ep0_queue(struct usb_ep *ep, struct usb_request *request,
 	return ret;
 }
 
-static void dwc3_ep0_stall_and_restart(struct dwc3 *dwc)
+void dwc3_ep0_stall_and_restart(struct dwc3 *dwc)
 {
 	struct dwc3_ep		*dep;
 
 	/* reinitialize physical ep1 */
 	dep = dwc->eps[1];
 	dep->flags = DWC3_EP_ENABLED;
+	dep->trb_enqueue = 0;
 
 	/* stall is always issued on EP0 */
 	dep = dwc->eps[0];
 	__dwc3_gadget_ep_set_halt(dep, 1, false);
 	dep->flags = DWC3_EP_ENABLED;
 	dwc->delayed_status = false;
+	dep->trb_enqueue = 0;
 
 	if (!list_empty(&dep->pending_list)) {
 		struct dwc3_request	*req;
@@ -240,7 +242,9 @@ static void dwc3_ep0_stall_and_restart(struct dwc3 *dwc)
 	}
 
 	dwc->ep0state = EP0_SETUP_PHASE;
-	dwc3_ep0_out_start(dwc);
+	complete(&dwc->ep0_in_setup);
+	if (dwc->softconnect)
+		dwc3_ep0_out_start(dwc);
 }
 
 int __dwc3_gadget_ep0_set_halt(struct usb_ep *ep, int value)
@@ -272,8 +276,6 @@ void dwc3_ep0_out_start(struct dwc3 *dwc)
 	struct dwc3_ep			*dep;
 	int				ret;
 
-	complete(&dwc->ep0_in_setup);
-
 	dep = dwc->eps[0];
 	dwc3_ep0_prepare_one_trb(dep, dwc->ep0_trb_addr, 8,
 			DWC3_TRBCTL_CONTROL_SETUP, false);
@@ -922,7 +924,9 @@ static void dwc3_ep0_complete_status(struct dwc3 *dwc,
 		dwc->setup_packet_pending = true;
 
 	dwc->ep0state = EP0_SETUP_PHASE;
-	dwc3_ep0_out_start(dwc);
+	complete(&dwc->ep0_in_setup);
+	if (dwc->softconnect)
+		dwc3_ep0_out_start(dwc);
 }
 
 static void dwc3_ep0_xfer_complete(struct dwc3 *dwc,
@@ -1073,7 +1077,7 @@ void dwc3_ep0_send_delayed_status(struct dwc3 *dwc)
 	__dwc3_ep0_do_control_status(dwc, dwc->eps[direction]);
 }
 
-static void dwc3_ep0_end_control_data(struct dwc3 *dwc, struct dwc3_ep *dep)
+void dwc3_ep0_end_control_data(struct dwc3 *dwc, struct dwc3_ep *dep)
 {
 	struct dwc3_gadget_ep_cmd_params params;
 	u32			cmd;
@@ -1083,7 +1087,8 @@ static void dwc3_ep0_end_control_data(struct dwc3 *dwc, struct dwc3_ep *dep)
 		return;
 
 	cmd = DWC3_DEPCMD_ENDTRANSFER;
-	cmd |= DWC3_DEPCMD_CMDIOC;
+	cmd |= dwc->connected ? 0 : DWC3_DEPCMD_HIPRI_FORCERM;
+	cmd |= dwc->connected ? DWC3_DEPCMD_CMDIOC : 0;
 	cmd |= DWC3_DEPCMD_PARAM(dep->resource_index);
 	memset(&params, 0, sizeof(params));
 	ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 520031ba38aa..19b8d837e9d0 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -885,12 +885,13 @@ static int __dwc3_gadget_ep_enable(struct dwc3_ep *dep, unsigned int action)
 		reg |= DWC3_DALEPENA_EP(dep->number);
 		dwc3_writel(dwc->regs, DWC3_DALEPENA, reg);
 
-		if (usb_endpoint_xfer_control(desc))
-			goto out;
-
 		/* Initialize the TRB ring */
 		dep->trb_dequeue = 0;
 		dep->trb_enqueue = 0;
+
+		if (usb_endpoint_xfer_control(desc))
+			goto out;
+
 		memset(dep->trb_pool, 0,
 		       sizeof(struct dwc3_trb) * DWC3_TRB_NUM);
 
@@ -2463,7 +2464,8 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
 	 * Per databook, when we want to stop the gadget, if a control transfer
 	 * is still in process, complete it and get the core into setup phase.
 	 */
-	if (!is_on && dwc->ep0state != EP0_SETUP_PHASE) {
+	if ((!is_on && (dwc->ep0state != EP0_SETUP_PHASE ||
+	     dwc->ep0_next_event != DWC3_EP0_COMPLETE))) {
 		reinit_completion(&dwc->ep0_in_setup);
 
 		ret = wait_for_completion_timeout(&dwc->ep0_in_setup,
@@ -2506,6 +2508,17 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
 		u32 count;
 
 		dwc->connected = false;
+
+		/*
+		 * Ensure no pending data/setup stages, and disable ep0 to
+		 * block further EP0 transactions before stopping pending
+		 * transfers.
+		 */
+		dwc3_ep0_end_control_data(dwc, dwc->eps[1]);
+		dwc3_ep0_stall_and_restart(dwc);
+		__dwc3_gadget_ep_disable(dwc->eps[0]);
+		__dwc3_gadget_ep_disable(dwc->eps[1]);
+
 		/*
 		 * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
 		 * Section 4.1.8 Table 4-7, it states that for a device-initiated
@@ -3587,8 +3600,10 @@ static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
 	bool interrupt)
 {
 	struct dwc3_gadget_ep_cmd_params params;
+	struct dwc3 *dwc = dep->dwc;
 	u32 cmd;
 	int ret;
+	int retries = 1;
 
 	if (!(dep->flags & DWC3_EP_TRANSFER_STARTED) ||
 	    (dep->flags & DWC3_EP_END_TRANSFER_PENDING))
@@ -3620,7 +3635,7 @@ static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
 	 *
 	 * This mode is NOT available on the DWC_usb31 IP.
 	 */
-
+retry:
 	cmd = DWC3_DEPCMD_ENDTRANSFER;
 	cmd |= force ? DWC3_DEPCMD_HIPRI_FORCERM : 0;
 	cmd |= interrupt ? DWC3_DEPCMD_CMDIOC : 0;
@@ -3628,6 +3643,23 @@ static void dwc3_stop_active_transfer(struct dwc3_ep *dep, bool force,
 	memset(&params, 0, sizeof(params));
 	ret = dwc3_send_gadget_ep_cmd(dep, cmd, &params);
 	WARN_ON_ONCE(ret);
+	if (ret == -ETIMEDOUT) {
+		if (!dwc->connected) {
+			/*
+			 * While the controller is in an active setup/control
+			 * transfer, the HW is unable to service other eps
+			 * potentially leading to an endxfer command timeout.
+			 * It was recommended to ensure that there are no
+			 * pending/cached setup packets stored in internal
+			 * memory.  Only way to achieve this is to issue another
+			 * start transfer, and retry.
+			 */
+			if (retries--) {
+				dwc3_ep0_out_start(dwc);
+				goto retry;
+			}
+		}
+	}
 	dep->resource_index = 0;
 
 	if (!interrupt)