Received-SPF: softfail (google.com: domain of transitioning linux-kernel-owner@vger.kernel.org does not designate 23.128.96.19 as permitted sender) client-ip=23.128.96.19;
From:   Aswath Govindraju <a-govindraju@ti.com>
CC:     Roger Quadros <rogerq@kernel.org>,
        Vignesh Raghavendra <vigneshr@ti.com>,
        Kishon Vijay Abraham I <kishon@ti.com>,
        Aswath Govindraju <a-govindraju@ti.com>,
        Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
        Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Felipe Balbi <balbi@kernel.org>, <linux-usb@vger.kernel.org>,
        <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH v4 2/2] drivers: usb: dwc3: Add AM62 USB wrapper driver
Date:   Thu, 14 Apr 2022 16:02:09 +0530
Message-ID: <20220414103211.16202-3-a-govindraju@ti.com>
In-Reply-To: <20220414103211.16202-1-a-govindraju@ti.com>
References: <20220414103211.16202-1-a-govindraju@ti.com>
MIME-Version: 1.0
Content-Type: text/plain
To:     unlisted-recipients:; (no To-header on input)
Precedence: bulk

In AM62 SoC, the Designware Core USB3 IP is progammed to operate in USB2.0
only mode. Add driver for AM62 USB DWC3 Wrapper.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---

Changes since v3:
- Removed the VBUS_VALID interrupt servicing as mode valid bit
  need not be switched based on the connect/disconnect event.
  The mode valid bit is being set during probe and cleared
  during remove

 drivers/usb/dwc3/Kconfig     |   9 +
 drivers/usb/dwc3/Makefile    |   1 +
 drivers/usb/dwc3/dwc3-am62.c | 332 +++++++++++++++++++++++++++++++++++
 3 files changed, 342 insertions(+)
 create mode 100644 drivers/usb/dwc3/dwc3-am62.c

diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
index c483f28b695d..cd9a734522a7 100644
--- a/drivers/usb/dwc3/Kconfig
+++ b/drivers/usb/dwc3/Kconfig
@@ -159,4 +159,13 @@ config USB_DWC3_XILINX
 	  This driver handles both ZynqMP and Versal SoC operations.
 	  Say 'Y' or 'M' if you have one such device.
 
+config USB_DWC3_AM62
+	tristate "Texas Instruments AM62 Platforms"
+	depends on ARCH_K3 || COMPILE_TEST
+	default USB_DWC3
+	help
+	  Support TI's AM62 platforms with DesignWare Core USB3 IP.
+	  The Designware Core USB3 IP is progammed to operate in
+	  in USB 2.0 mode only.
+	  Say 'Y' or 'M' here if you have one such device
 endif
diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
index 2d499de6f66a..9f66bd82b639 100644
--- a/drivers/usb/dwc3/Makefile
+++ b/drivers/usb/dwc3/Makefile
@@ -42,6 +42,7 @@ endif
 # and allyesconfig builds.
 ##
 
+obj-$(CONFIG_USB_DWC3_AM62)		+= dwc3-am62.o
 obj-$(CONFIG_USB_DWC3_OMAP)		+= dwc3-omap.o
 obj-$(CONFIG_USB_DWC3_EXYNOS)		+= dwc3-exynos.o
 obj-$(CONFIG_USB_DWC3_PCI)		+= dwc3-pci.o
diff --git a/drivers/usb/dwc3/dwc3-am62.c b/drivers/usb/dwc3/dwc3-am62.c
new file mode 100644
index 000000000000..730f2be46ef5
--- /dev/null
+++ b/drivers/usb/dwc3/dwc3-am62.c
@@ -0,0 +1,332 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dwc3-am62.c - TI specific Glue layer for AM62 DWC3 USB Controller
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/clk.h>
+#include <linux/regmap.h>
+#include <linux/pinctrl/consumer.h>
+
+/* USB WRAPPER register offsets */
+#define USBSS_PID			0x0
+#define USBSS_OVERCURRENT_CTRL		0x4
+#define USBSS_PHY_CONFIG		0x8
+#define USBSS_PHY_TEST			0xc
+#define USBSS_CORE_STAT			0x14
+#define USBSS_HOST_VBUS_CTRL		0x18
+#define USBSS_MODE_CONTROL		0x1c
+#define USBSS_WAKEUP_CONFIG		0x30
+#define USBSS_WAKEUP_STAT		0x34
+#define USBSS_OVERRIDE_CONFIG		0x38
+#define USBSS_IRQ_MISC_STATUS_RAW	0x430
+#define USBSS_IRQ_MISC_STATUS		0x434
+#define USBSS_IRQ_MISC_ENABLE_SET	0x438
+#define USBSS_IRQ_MISC_ENABLE_CLR	0x43c
+#define USBSS_IRQ_MISC_EOI		0x440
+#define USBSS_INTR_TEST			0x490
+#define USBSS_VBUS_FILTER		0x614
+#define USBSS_VBUS_STAT			0x618
+#define USBSS_DEBUG_CFG			0x708
+#define USBSS_DEBUG_DATA		0x70c
+#define USBSS_HOST_HUB_CTRL		0x714
+
+/* PHY CONFIG register bits */
+#define USBSS_PHY_VBUS_SEL_MASK		GENMASK(2, 1)
+#define USBSS_PHY_VBUS_SEL_SHIFT	1
+#define USBSS_PHY_LANE_REVERSE		BIT(0)
+
+/* MODE CONTROL register bits */
+#define USBSS_MODE_VALID	BIT(0)
+
+/* WAKEUP CONFIG register bits */
+#define USBSS_WAKEUP_CFG_OVERCURRENT_EN	BIT(3)
+#define USBSS_WAKEUP_CFG_LINESTATE_EN	BIT(2)
+#define USBSS_WAKEUP_CFG_SESSVALID_EN	BIT(1)
+#define USBSS_WAKEUP_CFG_VBUSVALID_EN	BIT(0)
+
+/* WAKEUP STAT register bits */
+#define USBSS_WAKEUP_STAT_OVERCURRENT	BIT(4)
+#define USBSS_WAKEUP_STAT_LINESTATE	BIT(3)
+#define USBSS_WAKEUP_STAT_SESSVALID	BIT(2)
+#define USBSS_WAKEUP_STAT_VBUSVALID	BIT(1)
+#define USBSS_WAKEUP_STAT_CLR		BIT(0)
+
+/* IRQ_MISC_STATUS_RAW register bits */
+#define USBSS_IRQ_MISC_RAW_VBUSVALID	BIT(22)
+#define USBSS_IRQ_MISC_RAW_SESSVALID	BIT(20)
+
+/* IRQ_MISC_STATUS register bits */
+#define USBSS_IRQ_MISC_VBUSVALID	BIT(22)
+#define USBSS_IRQ_MISC_SESSVALID	BIT(20)
+
+/* IRQ_MISC_ENABLE_SET register bits */
+#define USBSS_IRQ_MISC_ENABLE_SET_VBUSVALID	BIT(22)
+#define USBSS_IRQ_MISC_ENABLE_SET_SESSVALID	BIT(20)
+
+/* IRQ_MISC_ENABLE_CLR register bits */
+#define USBSS_IRQ_MISC_ENABLE_CLR_VBUSVALID	BIT(22)
+#define USBSS_IRQ_MISC_ENABLE_CLR_SESSVALID	BIT(20)
+
+/* IRQ_MISC_EOI register bits */
+#define USBSS_IRQ_MISC_EOI_VECTOR	BIT(0)
+
+/* VBUS_STAT register bits */
+#define USBSS_VBUS_STAT_SESSVALID	BIT(2)
+#define USBSS_VBUS_STAT_VBUSVALID	BIT(0)
+
+/* Mask for PHY PLL REFCLK */
+#define PHY_PLL_REFCLK_MASK	GENMASK(3, 0)
+
+#define DWC3_AM62_AUTOSUSPEND_DELAY	100
+
+struct dwc3_data {
+	struct device *dev;
+	void __iomem *usbss;
+	struct clk *usb2_refclk;
+	int rate_code;
+	struct regmap *syscon;
+	unsigned int offset;
+	unsigned int vbus_divider;
+};
+
+static const int dwc3_ti_rate_table[] = {	/* in KHZ */
+	9600,
+	10000,
+	12000,
+	19200,
+	20000,
+	24000,
+	25000,
+	26000,
+	38400,
+	40000,
+	58000,
+	50000,
+	52000,
+};
+
+static inline u32 dwc3_ti_readl(struct dwc3_data *data, u32 offset)
+{
+	return readl((data->usbss) + offset);
+}
+
+static inline void dwc3_ti_writel(struct dwc3_data *data, u32 offset, u32 value)
+{
+	writel(value, (data->usbss) + offset);
+}
+
+static int phy_syscon_pll_refclk(struct dwc3_data *data)
+{
+	struct device *dev = data->dev;
+	struct device_node *node = dev->of_node;
+	struct of_phandle_args args;
+	struct regmap *syscon;
+	int ret;
+
+	syscon = syscon_regmap_lookup_by_phandle(node, "ti,syscon-phy-pll-refclk");
+	if (IS_ERR(syscon)) {
+		dev_err(dev, "unable to get ti,syscon-phy-pll-refclk regmap\n");
+		return PTR_ERR(syscon);
+	}
+
+	data->syscon = syscon;
+
+	ret = of_parse_phandle_with_fixed_args(node, "ti,syscon-phy-pll-refclk", 1,
+					       0, &args);
+	if (ret)
+		return ret;
+
+	data->offset = args.args[0];
+
+	ret = regmap_update_bits(data->syscon, data->offset, PHY_PLL_REFCLK_MASK, data->rate_code);
+	if (ret) {
+		dev_err(dev, "failed to set phy pll reference clock rate\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int dwc3_ti_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = pdev->dev.of_node;
+	struct dwc3_data *data;
+	int i, ret;
+	unsigned long rate;
+	u32 reg;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->dev = dev;
+	platform_set_drvdata(pdev, data);
+
+	data->usbss = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(data->usbss)) {
+		dev_err(dev, "can't map IOMEM resource\n");
+		return PTR_ERR(data->usbss);
+	}
+
+	data->usb2_refclk = devm_clk_get(dev, "ref");
+	if (IS_ERR(data->usb2_refclk)) {
+		dev_err(dev, "can't get usb2_refclk\n");
+		return PTR_ERR(data->usb2_refclk);
+	}
+
+	/* Calculate the rate code */
+	rate = clk_get_rate(data->usb2_refclk);
+	rate /= 1000;	// To KHz
+	for (i = 0; i < ARRAY_SIZE(dwc3_ti_rate_table); i++) {
+		if (dwc3_ti_rate_table[i] == rate)
+			break;
+	}
+
+	if (i == ARRAY_SIZE(dwc3_ti_rate_table)) {
+		dev_err(dev, "unsupported usb2_refclk rate: %lu KHz\n", rate);
+		ret = -EINVAL;
+		goto err_clk_disable;
+	}
+
+	data->rate_code = i;
+
+	/* Read the syscon property and set the rate code */
+	ret = phy_syscon_pll_refclk(data);
+	if (ret)
+		goto err_clk_disable;
+
+	/* VBUS divider select */
+	data->vbus_divider = device_property_read_bool(dev, "ti,vbus-divider");
+	reg = dwc3_ti_readl(data, USBSS_PHY_CONFIG);
+	if (data->vbus_divider)
+		reg |= 1 << USBSS_PHY_VBUS_SEL_SHIFT;
+
+	dwc3_ti_writel(data, USBSS_PHY_CONFIG, reg);
+
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	/*
+	 * Don't ignore its dependencies with its children
+	 */
+	pm_suspend_ignore_children(dev, false);
+	clk_prepare_enable(data->usb2_refclk);
+	pm_runtime_get_noresume(dev);
+
+	ret = of_platform_populate(node, NULL, NULL, dev);
+	if (ret) {
+		dev_err(dev, "failed to create dwc3 core: %d\n", ret);
+		goto err_pm_disable;
+	}
+
+	/* Set mode valid bit to indicate role is valid */
+	reg = dwc3_ti_readl(data, USBSS_MODE_CONTROL);
+	reg |= USBSS_MODE_VALID;
+	dwc3_ti_writel(data, USBSS_MODE_CONTROL, reg);
+
+	/* Setting up autosuspend */
+	pm_runtime_set_autosuspend_delay(dev, DWC3_AM62_AUTOSUSPEND_DELAY);
+	pm_runtime_use_autosuspend(dev);
+	pm_runtime_mark_last_busy(dev);
+	pm_runtime_put_autosuspend(dev);
+	return 0;
+
+err_pm_disable:
+	clk_disable_unprepare(data->usb2_refclk);
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
+err_clk_disable:
+	clk_put(data->usb2_refclk);
+	return ret;
+}
+
+static int dwc3_ti_remove_core(struct device *dev, void *c)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+
+	platform_device_unregister(pdev);
+	return 0;
+}
+
+static int dwc3_ti_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct dwc3_data *data = platform_get_drvdata(pdev);
+	u32 reg;
+
+	device_for_each_child(dev, NULL, dwc3_ti_remove_core);
+
+	/* Clear mode valid bit */
+	reg = dwc3_ti_readl(data, USBSS_MODE_CONTROL);
+	reg &= ~USBSS_MODE_VALID;
+	dwc3_ti_writel(data, USBSS_MODE_CONTROL, reg);
+
+	pm_runtime_put_sync(dev);
+	clk_disable_unprepare(data->usb2_refclk);
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
+
+	clk_put(data->usb2_refclk);
+	platform_set_drvdata(pdev, NULL);
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int dwc3_ti_suspend_common(struct device *dev)
+{
+	struct dwc3_data *data = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(data->usb2_refclk);
+
+	return 0;
+}
+
+static int dwc3_ti_resume_common(struct device *dev)
+{
+	struct dwc3_data *data = dev_get_drvdata(dev);
+
+	clk_prepare_enable(data->usb2_refclk);
+
+	return 0;
+}
+
+static UNIVERSAL_DEV_PM_OPS(dwc3_ti_pm_ops, dwc3_ti_suspend_common,
+			    dwc3_ti_resume_common, NULL);
+
+#define DEV_PM_OPS	(&dwc3_ti_pm_ops)
+#else
+#define DEV_PM_OPS	NULL
+#endif /* CONFIG_PM */
+
+static const struct of_device_id dwc3_ti_of_match[] = {
+	{ .compatible = "ti,am62-usb"},
+	{},
+};
+MODULE_DEVICE_TABLE(of, dwc3_ti_of_match);
+
+static struct platform_driver dwc3_ti_driver = {
+	.probe		= dwc3_ti_probe,
+	.remove		= dwc3_ti_remove,
+	.driver		= {
+		.name	= "dwc3-am62",
+		.pm	= DEV_PM_OPS,
+		.of_match_table = dwc3_ti_of_match,
+	},
+};
+
+module_platform_driver(dwc3_ti_driver);
+
+MODULE_ALIAS("platform:dwc3-am62");
+MODULE_AUTHOR("Aswath Govindraju <a-govindraju@ti.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("DesignWare USB3 TI Glue Layer");
-- 
2.17.1