Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   David Virag <virag.david003@gmail.com>
Cc:     David Virag <virag.david003@gmail.com>,
        Rob Herring <robh+dt@kernel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
        Alim Akhtar <alim.akhtar@samsung.com>,
        Sylwester Nawrocki <s.nawrocki@samsung.com>,
        Tomasz Figa <tomasz.figa@gmail.com>,
        Chanwoo Choi <cw00.choi@samsung.com>,
        Michael Turquette <mturquette@baylibre.com>,
        Stephen Boyd <sboyd@kernel.org>,
        Sam Protsenko <semen.protsenko@linaro.org>,
        devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
        linux-samsung-soc@vger.kernel.org, linux-kernel@vger.kernel.org,
        linux-clk@vger.kernel.org
Subject: [PATCH 2/2] arm64: dts: exynos: Correct UART clocks on Exynos7885
Date:   Thu, 26 May 2022 07:58:40 +0200
Message-Id: <20220526055840.45209-3-virag.david003@gmail.com>
In-Reply-To: <20220526055840.45209-1-virag.david003@gmail.com>
References: <20220526055840.45209-1-virag.david003@gmail.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
To:     unlisted-recipients:; (no To-header on input)
Precedence: bulk

The clocks in the serial UART nodes were swapped by mistake on
Exynos7885. This only worked correctly because of a mistake in the clock
driver which has been fixed. With the fixed clock driver in place, the
baudrate of the UARTs get miscalculated. Fix this by correcting the
clocks in the dtsi.

Fixes: 06874015327b ("arm64: dts: exynos: Add initial device tree support for Exynos7885 SoC")
Signed-off-by: David Virag <virag.david003@gmail.com>
---
 arch/arm64/boot/dts/exynos/exynos7885.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/exynos/exynos7885.dtsi b/arch/arm64/boot/dts/exynos/exynos7885.dtsi
index 3170661f5b67..9c233c56558c 100644
--- a/arch/arm64/boot/dts/exynos/exynos7885.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos7885.dtsi
@@ -280,8 +280,8 @@ serial_0: serial@13800000 {
 			interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_bus>;
-			clocks = <&cmu_peri CLK_GOUT_UART0_EXT_UCLK>,
-				 <&cmu_peri CLK_GOUT_UART0_PCLK>;
+			clocks = <&cmu_peri CLK_GOUT_UART0_PCLK>,
+				 <&cmu_peri CLK_GOUT_UART0_EXT_UCLK>;
 			clock-names = "uart", "clk_uart_baud0";
 			samsung,uart-fifosize = <64>;
 			status = "disabled";
@@ -293,8 +293,8 @@ serial_1: serial@13810000 {
 			interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart1_bus>;
-			clocks = <&cmu_peri CLK_GOUT_UART1_EXT_UCLK>,
-				 <&cmu_peri CLK_GOUT_UART1_PCLK>;
+			clocks = <&cmu_peri CLK_GOUT_UART1_PCLK>,
+				 <&cmu_peri CLK_GOUT_UART1_EXT_UCLK>;
 			clock-names = "uart", "clk_uart_baud0";
 			samsung,uart-fifosize = <256>;
 			status = "disabled";
@@ -306,8 +306,8 @@ serial_2: serial@13820000 {
 			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart2_bus>;
-			clocks = <&cmu_peri CLK_GOUT_UART2_EXT_UCLK>,
-				 <&cmu_peri CLK_GOUT_UART2_PCLK>;
+			clocks = <&cmu_peri CLK_GOUT_UART2_PCLK>,
+				 <&cmu_peri CLK_GOUT_UART2_EXT_UCLK>;
 			clock-names = "uart", "clk_uart_baud0";
 			samsung,uart-fifosize = <256>;
 			status = "disabled";
-- 
2.35.1