Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
Date:   Fri, 26 Aug 2022 21:59:53 +0300
From:   Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To:     Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Cc:     devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
        linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org,
        linux-media@vger.kernel.org, Rob Herring <robh+dt@kernel.org>,
        Chen-Yu Tsai <wens@csie.org>,
        Jernej Skrabec <jernej.skrabec@gmail.com>,
        Samuel Holland <samuel@sholland.org>,
        Michael Turquette <mturquette@baylibre.com>,
        Stephen Boyd <sboyd@kernel.org>,
        Frank Rowand <frowand.list@gmail.com>,
        Maxime Ripard <mripard@kernel.org>,
        Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Subject: Re: [PATCH v5 5/6] ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller
 node
Message-ID: <YwkYKcffdRGnq+pK@pendragon.ideasonboard.com>
References: <20220826182803.604563-1-paul.kocialkowski@bootlin.com>
 <20220826182803.604563-6-paul.kocialkowski@bootlin.com>
MIME-Version: 1.0
Content-Type: text/plain; charset=utf-8
Content-Disposition: inline
In-Reply-To: <20220826182803.604563-6-paul.kocialkowski@bootlin.com>
Precedence: bulk

Hi Paul,

Thank you for the patch.

On Fri, Aug 26, 2022 at 08:28:02PM +0200, Paul Kocialkowski wrote:
> MIPI CSI-2 is supported on the A83T with a dedicated controller that
> covers both the protocol and D-PHY. It can be connected to the CSI
> interface as a V4L2 subdev through the fwnode graph.
> 
> This is not done by default since connecting the bridge without a
> subdev attached to it will cause a failure on the CSI driver.

No urgency, but would it be possible to fix this so that the CSI-2
receiver can be connected to the CSI unconditionally in DT ? The
connection exists at the hardware level in the SoC, and should thus
exist here too, regardless of whether or not a sensor is connected.

> Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
> ---
>  arch/arm/boot/dts/sun8i-a83t.dtsi | 26 ++++++++++++++++++++++++++
>  1 file changed, 26 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
> index 82fdb04122ca..ecf9f3b2c0c0 100644
> --- a/arch/arm/boot/dts/sun8i-a83t.dtsi
> +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
> @@ -1064,6 +1064,32 @@ csi: camera@1cb0000 {
>  			status = "disabled";
>  		};
>  
> +		mipi_csi2: csi@1cb1000 {
> +			compatible = "allwinner,sun8i-a83t-mipi-csi2";
> +			reg = <0x01cb1000 0x1000>;
> +			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_CSI>,
> +				 <&ccu CLK_CSI_SCLK>,
> +				 <&ccu CLK_MIPI_CSI>,
> +				 <&ccu CLK_CSI_MISC>;
> +			clock-names = "bus", "mod", "mipi", "misc";
> +			resets = <&ccu RST_BUS_CSI>;
> +			status = "disabled";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				mipi_csi2_in: port@0 {
> +					reg = <0>;
> +				};
> +
> +				mipi_csi2_out: port@1 {
> +					reg = <1>;
> +				};
> +			};
> +		};
> +
>  		hdmi: hdmi@1ee0000 {
>  			compatible = "allwinner,sun8i-a83t-dw-hdmi";
>  			reg = <0x01ee0000 0x10000>;

-- 
Regards,

Laurent Pinchart