Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1758062AbXFUSPV (ORCPT ); Thu, 21 Jun 2007 14:15:21 -0400 Received: (majordomo@vger.kernel.org) by vger.kernel.org id S1755433AbXFUSPK (ORCPT ); Thu, 21 Jun 2007 14:15:10 -0400 Received: from smtp-03.mandic.com.br ([200.225.81.143]:59825 "EHLO smtp-03.mandic.com.br" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1754190AbXFUSPI (ORCPT ); Thu, 21 Jun 2007 14:15:08 -0400 Message-ID: <467AC01E.4020503@mandic.com.br> Date: Thu, 21 Jun 2007 15:14:54 -0300 From: "Renato S. Yamane" User-Agent: Thunderbird 2.0.0.4 (X11/20070604) MIME-Version: 1.0 To: Kernel development list , shemminger@osdl.org Subject: sky2 crash on suspend to RAM Content-Type: text/plain; charset=ISO-8859-1; format=flowed Content-Transfer-Encoding: 8bit Sender: linux-kernel-owner@vger.kernel.org X-Mailing-List: linux-kernel@vger.kernel.org Content-Length: 8002 Lines: 160 Hi, Suspend to ram work very fine in my Toshiba M45-S355, but when laptop return (from RAM), my network connection crash, and I need unload and load again my sky2 module (using kernel 2.6.21.1). My NIC is: Marvell Technology Group Ltd. 88E8036 PCI-E Fast Ethernet Controller (rev 10) See below my logs when return from ram: kernel: sky2 eth1: disabling interface kernel: sky2 eth1: enabling interface kernel: sky2 eth1: ram buffer 4K kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready kernel: uhci_hcd 0000:00:1d.3: remove, state 4 kernel: usb usb4: USB disconnect, address 1 kernel: uhci_hcd 0000:00:1d.3: USB bus 4 deregistered kernel: ACPI: PCI interrupt for device 0000:00:1d.3 disabled kernel: uhci_hcd 0000:00:1d.2: remove, state 4 kernel: usb usb3: USB disconnect, address 1 kernel: uhci_hcd 0000:00:1d.2: USB bus 3 deregistered kernel: ACPI: PCI interrupt for device 0000:00:1d.2 disabled kernel: uhci_hcd 0000:00:1d.1: remove, state 4 kernel: usb usb2: USB disconnect, address 1 kernel: uhci_hcd 0000:00:1d.1: USB bus 2 deregistered kernel: ACPI: PCI interrupt for device 0000:00:1d.1 disabled kernel: uhci_hcd 0000:00:1d.0: remove, state 1 kernel: usb usb1: USB disconnect, address 1 kernel: usb 1-1: USB disconnect, address 4 kernel: uhci_hcd 0000:00:1d.0: USB bus 1 deregistered kernel: ACPI: PCI interrupt for device 0000:00:1d.0 disabled kernel: Stopping tasks ... done. kernel: Suspending console(s) kernel: sky2 eth1: Link is up at 100 Mbps, full duplex, flow control both kernel: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready kernel: ACPI: PCI interrupt for device 0000:05:06.4 disabled kernel: ACPI: PCI interrupt for device 0000:05:06.3 disabled kernel: eth2: Going into suspend... kernel: ACPI: PCI interrupt for device 0000:05:04.0 disabled kernel: sky2 eth1: disabling interface kernel: ACPI: PCI interrupt for device 0000:00:1f.2 disabled kernel: ACPI: PCI interrupt for device 0000:00:1e.3 disabled kernel: ACPI: PCI interrupt for device 0000:00:1e.2 disabled kernel: ACPI: PCI interrupt for device 0000:00:1d.7 disabled kernel: Intel machine check architecture supported. kernel: Intel machine check reporting enabled on CPU#0. kernel: ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 kernel: ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 kernel: ACPI: PCI Interrupt 0000:00:1c.1[B] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 kernel: PCI: Enabling device 0000:00:1d.7 (0000 -> 0002) kernel: ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10 kernel: ACPI: PCI Interrupt 0000:00:1e.2[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 kernel: ACPI: PCI Interrupt 0000:00:1e.3[B] -> Link [LNKE] -> GSI 5 (level, low) -> IRQ 5 kernel: ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 kernel: sky2 eth1: enabling interface kernel: sky2 eth1: ram buffer 4K kernel: eth2: Coming out of suspend... kernel: PCI: Enabling device 0000:05:04.0 (0000 -> 0002) kernel: ACPI: PCI Interrupt 0000:05:04.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 kernel: ACPI: PCI Interrupt 0000:05:06.2[C] -> Link [LNKG] -> GSI 6 (level, low) -> IRQ 6 kernel: ACPI: PCI Interrupt 0000:05:06.3[D] -> Link [LNKE] -> GSI 5 (level, low) -> IRQ 5 kernel: ACPI: PCI Interrupt 0000:05:06.4[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 kernel: ata1.00: configured for UDMA/100 kernel: SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB) kernel: sda: Write Protect is off kernel: SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA kernel: sky2 eth1: Link is up at 100 Mbps, full duplex, flow control both kernel: ata2.00: configured for UDMA/33 kernel: Restarting tasks ... done. kernel: ipw2200: Radio Frequency Kill Switch is On: kernel: Kill switch must be turned off for wireless networking to work. kernel: ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[b8000000-b80007ff] Max Packet=[2048] IR/IT contexts=[4/8] kernel: eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) kernel: USB Universal Host Controller Interface driver v3.0 kernel: ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10 kernel: uhci_hcd 0000:00:1d.0: UHCI Host Controller kernel: uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 kernel: uhci_hcd 0000:00:1d.0: irq 10, io base 0x00001200 kernel: usb usb1: configuration #1 chosen from 1 choice kernel: hub 1-0:1.0: USB hub found kernel: hub 1-0:1.0: 2 ports detected kernel: ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 kernel: uhci_hcd 0000:00:1d.1: UHCI Host Controller kernel: uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 kernel: uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001220 kernel: usb usb2: configuration #1 chosen from 1 choice kernel: hub 2-0:1.0: USB hub found kernel: hub 2-0:1.0: 2 ports detected kernel: ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 kernel: uhci_hcd 0000:00:1d.2: UHCI Host Controller kernel: uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 kernel: uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001240 kernel: usb usb3: configuration #1 chosen from 1 choice kernel: hub 3-0:1.0: USB hub found kernel: hub 3-0:1.0: 2 ports detected kernel: ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 kernel: uhci_hcd 0000:00:1d.3: UHCI Host Controller kernel: uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 kernel: uhci_hcd 0000:00:1d.3: irq 11, io base 0x00001260 kernel: usb usb4: configuration #1 chosen from 1 choice kernel: hub 4-0:1.0: USB hub found kernel: hub 4-0:1.0: 2 ports detected kernel: usb 1-1: new low speed USB device using uhci_hcd and address 2 kernel: sky2 eth1: disabling interface kernel: sky2 eth1: enabling interface kernel: sky2 eth1: ram buffer 4K kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready kernel: usb 1-1: configuration #1 chosen from 1 choice kernel: input: Microsoft Microsoft 3-Button Mouse with IntelliEye? as /class/input/input8 kernel: input: USB HID v1.00 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye?] on usb-0000:00:1d.0-1 kernel: ADDRCONF(NETDEV_UP): eth2: link is not ready kernel: sky2 eth1: Link is up at 100 Mbps, full duplex, flow control both kernel: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready dhcdbd: message_handler: message handler not found under /com/redhat/dhcp/eth1 for sub-path eth1.dbus.get.host_name dhcdbd: message_handler: message handler not found under /com/redhat/dhcp/eth1 for sub-path eth1.dbus.get.domain_name dhcdbd: message_handler: message handler not found under /com/redhat/dhcp/eth1 for sub-path eth1.dbus.get.nis_domain dhcdbd: message_handler: message handler not found under /com/redhat/dhcp/eth1 for sub-path eth1.dbus.get.nis_servers gconfd (yamane-5230): iniciando (vers?o 2.16.1), pid 5230 usu?rio 'yamane' gconfd (yamane-5230): Address "xml:readonly:/etc/gconf/gconf.xml.mandatory" resolved from a config source with only read permissions in position 0 gconfd (yamane-5230): O endere?o "xml:readwrite:/home/yamane/.gconf" resolved from a config source with write permissions in positiono 1 gconfd (yamane-5230): Address "xml:readonly:/etc/gconf/gconf.xml.defaults" resolved from a config source with only read permissions in position 2 gconfd (yamane-5230): Address "xml:readonly:/var/lib/gconf/debian.defaults" resolved from a config source with only read permissions in position 3 gconfd (yamane-5230): Address "xml:readonly:/var/lib/gconf/defaults" resolved from a config source with only read permissions in position 4 - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/