Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
Received-SPF: Pass (protection.outlook.com: domain of xilinx.com designates
 149.199.62.198 as permitted sender) receiver=protection.outlook.com;
 client-ip=149.199.62.198; helo=xsj-pvapexch02.xlnx.xilinx.com; pr=C
Envelope-to: broonie@kernel.org,
 robh+dt@kernel.org,
 krzysztof.kozlowski+dt@linaro.org,
 akumarma@amd.com,
 git@amd.com,
 linux-spi@vger.kernel.org,
 linux-arm-kernel@lists.infradead.org,
 linux-kernel@vger.kernel.org,
 devicetree@vger.kernel.org,
 amit.kumar-mahapatra@amd.com
From:   Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
To:     <broonie@kernel.org>, <robh+dt@kernel.org>,
        <krzysztof.kozlowski+dt@linaro.org>
CC:     <akumarma@amd.com>, <git@amd.com>, <michal.simek@xilinx.com>,
        <linux-spi@vger.kernel.org>,
        <linux-arm-kernel@lists.infradead.org>,
        <linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
        <amit.kumar-mahapatra@amd.com>,
        Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Subject: [PATCH v3 2/7] spi: spi-zynqmp-gqspi: Set CPOL and CPHA during hardware init
Date:   Sun, 25 Sep 2022 23:37:34 +0530
Message-ID: <20220925180739.21612-3-amit.kumar-mahapatra@xilinx.com>
In-Reply-To: <20220925180739.21612-1-amit.kumar-mahapatra@xilinx.com>
References: <20220925180739.21612-1-amit.kumar-mahapatra@xilinx.com>
MIME-Version: 1.0
Content-Type: text/plain
X-MS-Exchange-CrossTenant-OriginalArrivalTime: 25 Sep 2022 18:08:13.7742
 (UTC)
X-MS-Exchange-CrossTenant-Network-Message-Id: e0a629be-bff3-4022-182f-08da9f20e9ec
X-MS-Exchange-CrossTenant-Id: 657af505-d5df-48d0-8300-c31994686c5c
X-MS-Exchange-CrossTenant-OriginalAttributedTenantConnectingIp: TenantId=657af505-d5df-48d0-8300-c31994686c5c;Ip=[149.199.62.198];Helo=[xsj-pvapexch02.xlnx.xilinx.com]
X-MS-Exchange-CrossTenant-AuthSource: SN1NAM02FT0014.eop-nam02.prod.protection.outlook.com
X-MS-Exchange-CrossTenant-AuthAs: Anonymous
X-MS-Exchange-CrossTenant-FromEntityHeader: HybridOnPrem
X-MS-Exchange-Transport-CrossTenantHeadersStamped: CO6PR02MB7697
X-Spam-Status: No, score=-1.9 required=5.0 tests=BAYES_00,DKIM_SIGNED,
        DKIM_VALID,RCVD_IN_DNSWL_NONE,RCVD_IN_MSPIKE_H2,SPF_HELO_PASS,SPF_PASS
        autolearn=ham autolearn_force=no version=3.4.6
X-Spam-Checker-Version: SpamAssassin 3.4.6 (2021-04-09) on
        lindbergh.monkeyblade.net
Precedence: bulk
List-ID: <linux-kernel.vger.kernel.org>
X-Mailing-List: linux-kernel@vger.kernel.org

During every transfer GQSPI driver writes the CPOL & CPHA values to the
configuration register. But the CPOL & CPHA values do not change in between
multiple transfers, so moved the CPOL & CPHA initialization to hardware
init so that the values are written only once.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
---
 drivers/spi/spi-zynqmp-gqspi.c | 32 +++++++++++++++++---------------
 1 file changed, 17 insertions(+), 15 deletions(-)

diff --git a/drivers/spi/spi-zynqmp-gqspi.c b/drivers/spi/spi-zynqmp-gqspi.c
index 973008a30a09..1b56dd29057f 100644
--- a/drivers/spi/spi-zynqmp-gqspi.c
+++ b/drivers/spi/spi-zynqmp-gqspi.c
@@ -266,7 +266,9 @@ static void zynqmp_gqspi_selectslave(struct zynqmp_qspi *instanceptr,
  *	- Enable manual slave select
  *	- Enable manual start
  *	- Deselect all the chip select lines
- *	- Set the little endian mode of TX FIFO and
+ *	- Set the little endian mode of TX FIFO
+ *	- Set clock phase
+ *	- Set clock polarity and
  *	- Enable the QSPI controller
  */
 static void zynqmp_qspi_init_hw(struct zynqmp_qspi *xqspi)
@@ -305,10 +307,17 @@ static void zynqmp_qspi_init_hw(struct zynqmp_qspi *xqspi)
 	config_reg |= GQSPI_CFG_WP_HOLD_MASK;
 	/* Clear pre-scalar by default */
 	config_reg &= ~GQSPI_CFG_BAUD_RATE_DIV_MASK;
-	/* CPHA 0 */
-	config_reg &= ~GQSPI_CFG_CLK_PHA_MASK;
-	/* CPOL 0 */
-	config_reg &= ~GQSPI_CFG_CLK_POL_MASK;
+	/* Set CPHA */
+	if (xqspi->ctlr->mode_bits & SPI_CPHA)
+		config_reg |= GQSPI_CFG_CLK_PHA_MASK;
+	else
+		config_reg &= ~GQSPI_CFG_CLK_PHA_MASK;
+	/* Set CPOL */
+	if (xqspi->ctlr->mode_bits & SPI_CPOL)
+		config_reg |= GQSPI_CFG_CLK_POL_MASK;
+	else
+		config_reg &= ~GQSPI_CFG_CLK_POL_MASK;
+
 	zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg);
 
 	/* Clear the TX and RX FIFO */
@@ -470,14 +479,6 @@ static int zynqmp_qspi_config_op(struct zynqmp_qspi *xqspi,
 
 	config_reg = zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST);
 
-	/* Set the QSPI clock phase and clock polarity */
-	config_reg &= (~GQSPI_CFG_CLK_PHA_MASK) & (~GQSPI_CFG_CLK_POL_MASK);
-
-	if (qspi->mode & SPI_CPHA)
-		config_reg |= GQSPI_CFG_CLK_PHA_MASK;
-	if (qspi->mode & SPI_CPOL)
-		config_reg |= GQSPI_CFG_CLK_POL_MASK;
-
 	config_reg &= ~GQSPI_CFG_BAUD_RATE_DIV_MASK;
 	config_reg |= (baud_rate_val << GQSPI_CFG_BAUD_RATE_DIV_SHIFT);
 	zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg);
@@ -1170,6 +1171,9 @@ static int zynqmp_qspi_probe(struct platform_device *pdev)
 		goto clk_dis_all;
 	}
 
+	ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD |
+		SPI_TX_DUAL | SPI_TX_QUAD;
+
 	/* QSPI controller initializations */
 	zynqmp_qspi_init_hw(xqspi);
 
@@ -1207,8 +1211,6 @@ static int zynqmp_qspi_probe(struct platform_device *pdev)
 	ctlr->setup = zynqmp_qspi_setup_op;
 	ctlr->max_speed_hz = clk_get_rate(xqspi->refclk) / 2;
 	ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
-	ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD |
-			    SPI_TX_DUAL | SPI_TX_QUAD;
 	ctlr->dev.of_node = np;
 	ctlr->auto_runtime_pm = true;
 
-- 
2.17.1