Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Fabrice Gasnier <fabrice.gasnier@foss.st.com>
To:     <alexandre.torgue@foss.st.com>, <robh+dt@kernel.org>,
        <krzysztof.kozlowski+dt@linaro.org>
CC:     <amelie.delaunay@foss.st.com>, <devicetree@vger.kernel.org>,
        <linux-arm-kernel@lists.infradead.org>,
        <linux-kernel@vger.kernel.org>,
        <linux-stm32@st-md-mailman.stormreply.com>,
        <fabrice.gasnier@foss.st.com>
Subject: [PATCH 09/10] ARM: dts: stm32: enable USB OTG in dual role mode on stm32mp135f-dk
Date:   Fri, 14 Oct 2022 11:26:50 +0200
Message-ID: <20221014092651.25202-10-fabrice.gasnier@foss.st.com>
In-Reply-To: <20221014092651.25202-1-fabrice.gasnier@foss.st.com>
References: <20221014092651.25202-1-fabrice.gasnier@foss.st.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Content-Type: text/plain
Precedence: bulk

The USB OTG controller provides the USB data available on stm32mp135f-dk,
on the Type-C connector. Data role is determined by "usb-role-switch".

A STM32G0 provides the USB Type-C and Power Delivery connectivity.
It controls dual role power and dual role data through UCSI protocol over
I2C. It's wired on I2C1, with an interrupt pin on PI2 GPIO.
Its firmware maybe updated over I2C, so use the optional firmware-name
to enable firmware update.

Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
---
 arch/arm/boot/dts/stm32mp135f-dk.dts | 34 ++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/arch/arm/boot/dts/stm32mp135f-dk.dts b/arch/arm/boot/dts/stm32mp135f-dk.dts
index 02ff2bc664da..1c92bf096397 100644
--- a/arch/arm/boot/dts/stm32mp135f-dk.dts
+++ b/arch/arm/boot/dts/stm32mp135f-dk.dts
@@ -95,6 +95,28 @@ &i2c1 {
 	/* spare dmas for other usage */
 	/delete-property/dmas;
 	/delete-property/dma-names;
+
+	stm32g0@53 {
+		compatible = "st,stm32g0-typec";
+		reg = <0x53>;
+		/* Alert pin on PI2 */
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpioi>;
+		/* Internal pull-up on PI2 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&stm32g0_intn_pins_a>;
+		firmware-name = "stm32g0-ucsi.mp135f-dk.fw";
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+
+			port {
+				con_usb_c_g0_ep: endpoint {
+					remote-endpoint = <&usbotg_hs_ep>;
+				};
+			};
+		};
+	};
 };
 
 &i2c5 {
@@ -158,6 +180,18 @@ hub@1 {
 	};
 };
 
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	usb-role-switch;
+	status = "okay";
+	port {
+		usbotg_hs_ep: endpoint {
+			remote-endpoint = <&con_usb_c_g0_ep>;
+		};
+	};
+};
+
 &usbphyc {
 	status = "okay";
 };
-- 
2.25.1