Received-SPF: pass (google.com: domain of linux-kernel-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Martin Blumenstingl <martin.blumenstingl@googlemail.com>
To:     linux@roeck-us.net, linux-hwmon@vger.kernel.org
Cc:     jdelvare@suse.com, linux-kernel@vger.kernel.org,
        Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Subject: [RFC PATCH v2 3/4] hwmon: (jc42) Restore the min/max/critical temperatures on resume
Date:   Thu, 20 Oct 2022 23:03:19 +0200
Message-Id: <20221020210320.1624617-4-martin.blumenstingl@googlemail.com>
In-Reply-To: <20221020210320.1624617-1-martin.blumenstingl@googlemail.com>
References: <20221020210320.1624617-1-martin.blumenstingl@googlemail.com>
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit
Precedence: bulk

The JC42 compatible thermal sensor on Kingston KSM32ES8/16ME DIMMs
(using Micron E-Die) is an ST Microelectronics STTS2004 (manufacturer
0x104a, device 0x2201). It does not keep the previously programmed
minimum, maximum and critical temperatures after system suspend and
resume (which is a shutdown / startup cycle for the JC42 temperature
sensor). This results in an alarm on system resume because the hardware
default for these values is 0°C (so any environment temperature greater
than 0°C will trigger the alarm).

Example before system suspend:
  jc42-i2c-0-1a
  Adapter: SMBus PIIX4 adapter port 0 at 0b00
  temp1:        +34.8°C  (low  =  +0.0°C)
                         (high = +85.0°C, hyst = +85.0°C)
                         (crit = +95.0°C, hyst = +95.0°C)

Example after system resume (without this change):
  jc42-i2c-0-1a
  Adapter: SMBus PIIX4 adapter port 0 at 0b00
  temp1:        +34.8°C  (low  =  +0.0°C)             ALARM (HIGH, CRIT)
                         (high =  +0.0°C, hyst =  +0.0°C)
                         (crit =  +0.0°C, hyst =  +0.0°C)

Apply the cached values from the JC42_REG_TEMP_UPPER,
JC42_REG_TEMP_LOWER, JC42_REG_TEMP_CRITICAL and JC42_REG_SMBUS (where
the SMBUS register is not related to this issue but a side-effect of
using regcache_sync() during system resume with the previously
cached/programmed values. This fixes the alarm due to the hardware
defaults of 0°C because the previously applied limits (set by userspace)
are re-applied on system resume.

Fixes: 175c490c9e7f ("hwmon: (jc42) Add support for STTS2004 and AT30TSE004")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
---
 drivers/hwmon/jc42.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/hwmon/jc42.c b/drivers/hwmon/jc42.c
index 3f524ab5451c..61311483a5c6 100644
--- a/drivers/hwmon/jc42.c
+++ b/drivers/hwmon/jc42.c
@@ -582,6 +582,10 @@ static int jc42_suspend(struct device *dev)
 
 	data->config |= JC42_CFG_SHUTDOWN;
 	regmap_write(data->regmap, JC42_REG_CONFIG, data->config);
+
+	regcache_cache_only(data->regmap, true);
+	regcache_mark_dirty(data->regmap);
+
 	return 0;
 }
 
@@ -589,9 +593,13 @@ static int jc42_resume(struct device *dev)
 {
 	struct jc42_data *data = dev_get_drvdata(dev);
 
+	regcache_cache_only(data->regmap, false);
+
 	data->config &= ~JC42_CFG_SHUTDOWN;
 	regmap_write(data->regmap, JC42_REG_CONFIG, data->config);
-	return 0;
+
+	/* Restore cached register values to hardware */
+	return regcache_sync(data->regmap);
 }
 
 static const struct dev_pm_ops jc42_dev_pm_ops = {
-- 
2.38.1